Search Documents

By J. Scott McDougall, J. Herman P. Eng. Vanderlaag

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. The optimum warning alarm must be fast and able to reach all miners, regardless of their location or work activity. Current means of fire warning are varied, and include such methods as stench, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. A novel fire warning alarm which enables instantaneous warning of all underground personnel, the Canary Nine Messenger System, has been developed by VLF Magnetic Systems Inc. in conjunction with Noranda Technology Centre and the U.S. Department of the Interior - Bureau of Nines. The warning is sent by an electromagnetic signal which penetrates through mine rock to receivers housed in the battery packs which also power each miner's cap lamp. A loud buzzer in the integrated battery/receiver unit and the flashing of the cap lamp alerts miners to incoming messages. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This report describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, and the design of recently available transmitter and receivers.

Jan 1, 1995

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By F. Ferella

In this paper several leaching tests were per-formed to optimize the leaching section of a hydrometallurgical process for the recycling of alkaline and zinc-carbon batteries. Zinc and manganese oxides were dissolved by an acidic-reductive leaching using sulphuric acid and oxalic acid as reductant. Leaching tests were developed according to a full factorial design. The operational variables were pulp percentage, sulphuric acid concentration, temperature and oxalic acid concentration. Additional tests were performed to evaluate the precipitation rate of Mn and Zn oxalates. Finally a hydrometallurgical process were proposed for the recycling of alkaline and zinc-carbon batteries, in which Zn and MnO2 are recovered from purified solution by electrowinning: Zn is recovered as metallic compound, while Mn can be recovered as electrolytic manganese dioxide (EMD), but recovery of further manganese compounds is possible with simple process changes.

Jan 1, 2006

By John A. L. Campbell

Although there has been an increased interest in the electrokinetic properties of coal (1) research on the subject is still in an early stage of development (2,3,4,5,6,7) To the author's knowledge, no electrokinetic studies have been made on coal lithotypes - particularly anthracite lithotypes. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods, It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published (8). The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results, however, the results are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation.

Jan 1, 1969

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The effectiveness of the grouting of saturated, fractured rock in the vicinity of underground workings depends to a great extent on the correct interpretation of the specific hydrogeological conditions at the site. During the planning of grouting operations, calculations of the hydrogeologic co-efficients and of the parameters of the isolating grout curtain(s) and the procedures for forming the curtain(s) must be based on valid hydrogeologic characteristics of the fracture system of the rock within each hydrostratigraphic unit (Anon., 1976). This chapter presents a discussion of the background information that must be collected for these purposes. Details of testing are presented in Chapter 3. The general design of new or the reconstruction of existing underground workings requires a broadly based organization having the expertise to develop a grouting operations plan once it acquires the necessary information. The needed information includes: 1) general information about the hydrogeologic section, 2) the engineering design of the underground workings, 3) the geology of the region, 4) the hydrochemistry of the ground water, 5) the hydraulic properties of the rock, 6) the characterization of all gases present, and 7) characterization of the rock's physical-mechanical properties which is necessary to avoid or control hydrofracturing . The geological documentation portion of the hydrogeological investigation is prepared based on the results of geologic mapping, geophysical surveys and on geo-exploratory operations at a regional and local scale. Geological data from the excavation of other underground workings in adjacent areas of the region is also included. Finally the results of site specific investigations in boreholes constructed at the site of the proposed underground activity are incorporated. A section of the preliminary report entitled "General Information about the Project Site" patterned after the parent STG guidance document on this subject must be com- piled based on the contents of geological reports and on the general construction plan for a new project or the plan for reconstruction of an existing operation. This section of the preliminary report must contain concise information about the conditions under which the planned grouting operations are to be conducted. The information must cover the geo- graphic, administrative, and economic subject areas also. Information about sources of electrical power, heat and water supplies, the presence and characteristics of local construction materials suitable for making grout (particularly clay and cement for the clay-based grout), transportation, and the status of communication lines and other services must be included in this section. Map scales for this section should be on the order of 1:25,000. The technical characterization of planned underground workings is presented in a project report chapter called "General Construction Plan for a New or the Restoration of an Old Operation. " The characterization comprises concise information about the purpose of the workings, the planned depths (for shafts) and the length (for horizontal and inclined workings), the inside and excavated diameters (for shafts), the cross-sectional area (for inclined and horizontal workings), and the face and mouth markers. If excavated underground workings exist in the region, then a concise description of them must be provided. The characterization of all excavations and all operational conditions must be specified. The location within the general structure of the proposed operation is specified. Flow charts must be included in this section that show: 1) the plan for opening the deposit, 2) the plans of the mining operations, and 3) the planned geological sections as they relate to the main workings. These graphical flow charts and appendices are drawn in scales of 1:2000 or 1:5000. 2.1 GEOLOGICAL CHARACTERIZATION The geological characterization of a site of proposed underground workings includes the following principal subject areas: stratigraphy, lithology, structural geology and a characterization of the status of fracturing. 2.1.1 STRATIGRAPHY AND LITHOLOGY A description of the geological section of the rocks to be intersected by the planned underground workings is complied on the basis of: 1) research data derived from core extracted from exploratory boreholes and monitoring boreholes, 2) the documentation and mapping of all natural out- crops in the region, 3) the data from all existing under-ground workings in the regions where operations are being canied out already, along with data from adjacent regions, 4) the data from surface and borehole geophysical investigations (standard and specially developed logging methods, and 5) regional stratigraphy. The geological description of the rock must express the maximum detail possible. The description provides the name of the rock, the granulometric composition (for fragmented rock), the composition and type of stratification, the drilling characteristics of the rock, a visual estimate of porosity and density for each stratum identified, the karstic

Jan 1, 1993

By W. A. Cincilla, S. C. Tadolini

INTRODUCTION Resin bolting systems continue to gain popularity in underground coal mines in the United States, and their general success under a wide range of geological and operational conditions is well documented. In 1984, 36% of all bolts used were resin-grouted systems. However, many questions dealing with basic support mechanisms and the influence of various factors on bolt effectiveness in situ remain only partially answered. The Bureau of Mines' Denver Research Center conducted a major research project to investigate the influence of installation procedures on the effectiveness of resin-grouted roof bolts. The project consisted of two main studies: the first dealing with the contribution of bearing plates to the load-carrying capability of the bolt; the second examining the relationship between installed grout column and the anchorage capacity as measured by the standard pull-out test. Additionally, a finite-element computer model and other analytical and empirical techniques were applied to aid in the basic understanding of the test procedures and to examine the load transfer mechanism in resin-grouted bolts, which to date has not been comprehensively assessed. The plate study includes field test results from two mines (Fig. 1). At these test sites two behavioral parameters were measured: the actual loads that bearing plates were subjected to when installed in conjunction with full-column resin grouted bolts, and the roof movements generated by the applied loads. Results indicate that bearing plates are subjected to varying degrees of loading, which range from conventional installation pressures of 2.2 kN (500 lb), up to a measured load of 142.4 kN (32,000 lb) when the immediate roof is shifting and deforming. These measured loads indicate that the bearing plate is an integral part of the support system. Differential sag stations, installed to monitor roof displacements in the test sites, show the highest degrees of loading occur in conjunction with the largest amounts of movement. The column-length study addresses possible reductions in anchorage capacity of "full column" bolts. These reductions could result from such factors as the loss of grout to surrounding strata, or improper mixing of catalyst and resin. Field test sites were established at eleven mines located in major coal mining districts throughout the United States (Fig. 1). Four major roof-rock types were represented in the study: shale,

Jan 1, 1986

By Mike D. Adams

Testwork was conducted on loaded carbon samples from a small gold mine in South Africa. It was shown that a 75% saving in reagent consumption in the Zadra elution circuit could be achieved by adopting a cyanide-free elution approach, i.e. by cutting back the NaCN level from 1 % to nil, and the NaOH level from 3% to 1 %. This process change was also shown to result in a 20% improvement in the elution kinetics. Furthermore, it was also shown that a 50% enhancement in elution rate over the current situation could be achieved by use of an eluant containing 0.5% NaOH and 0.15% NaCN, corresponding to an 84% saving in reagent consumption. A further improvement in elution kinetics was found to occur by increasing the NaCN level to 3%, but this would lead to a concomitant increase in reagent consumption, due to the decomposition of cyanide at high temperatures. The presence of base metals loaded onto the carbon was also found to have a significant effect on the elution. Copper tends to adsorb as Cu(CN)2- during the adsorption stage, and acid washing converts this species to CuCN. Copper in this form is not eluted during cyanide-free elution, whereas it is eluted during a conventional cyanide elution, consuming the initial cyanide in the process. The elution data was analysed and the fit to a simple model was verified.

Jan 1, 1995

By Owen E. Owens

INTRODUCTION This paper deals with the main components in exploring for and developing a gold ore deposit. It addresses geology, exploration drilling, ore reserves, and evaluation criteria in an integrated manner to present an overall picture. Gold forms such a small component of a gold ore body, that particular care should be taken in dealing with the data from a developing deposit. The paper lists the main gold ore deposit types and their character. Their differences, as well as differences to other types of ore deposits, are important to understanding exploration approaches, and problems of ore reserve definition. Gold exploration has enjoyed a great boom in recent years. Many new ore deposits have been developed but experience shows that definition of gold is not a simple straight forward process and this outline attempts to point out some of the important aspects of ore reserve definition including some pitfalls. GOLD DEPOSIT TYPES The Witwatersrand deposits in South Africa produce about 50% of the world's gold. The gold occurs as fine grains in thin beds within gently dipping quartz pebble fan conglomerates usually with associated pyrite grains. It is characterized by rather uniform distribution of gold along thin layers within the conglomerate.

Jan 1, 1988

By J. A. Meech, C. A. Harris

Expert Systems are being used in the Mineral Industry with ever­increasing frequency. A major advantage of these systems over conventional computer programs is that the knowledge and intelligence of human experts can be captured directly onto a computer for transfer to novices or other lesser experts. These programs allow rapid construction of process models that are not well-understood in fundamental terms, but for which good operational reasoning exists. In addition, user-friendly access to "high-tech" knowledge can be provided to unsophisticated personnel who otherwise might be turned off by unintelligible jargon. As such, these systems can be important training tools for new operators. This paper describes the features of Expert Systems that relate to gold processing plants. Applications include grinding circuit control, supervisory control of reagent addition and pulp density, monitoring and control of CIP/CIL carbon inventories and the operation of carbon stripping and regeneration facilities. A consultative Expert System is described that provides advice on laboratory cyanidation testwork

Jan 1, 1992

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By Jorgen Elbrond

The calculation of open pit operations' capacities has been the subject of many studies using computer simulations. The common problems of simulation are that if one desires a realistic picture of an operation the programming work becomes long and expensive and that the program requires a large computer and long time to run. The method presented in this paper overcomes these problems by using a straightforward calculation procedure. It is based on the queuing theory's simple formula for waiting time in a closed circuit and uses a system of correction factors, which reflect the loading, travel, and dumping times' relative variabilities and which have been found by 1) mathematical analysis and 2) simulations of basic circuits. The method includes the main parameters of the operation: numbers, sizes and operational availabilities of trucks, shovels and dumping point, distribution of the production over shovels, trucks' loading, travel (loaded and empty) and dumping times as well as their variabilities, shift's composition. The procedure models: the average duration of a complete truck cycle during stationary and non-stationary periods during the shift as a function of the number of trucks in the circuit, the composition of the average 100% operated shift, the simultaneous probabilities of operationally available shovels and trucks and the distribution of shovels and trucks according to production and cycle times. The procedure can be programmed for a small computer and requires only short computing time, which makes extensive studies of various parameter combinations practical to carry out. The development of the method is an extension of previous work by Morgan and Peterson {1}, who by simulation established the relation between the match factor (which is the ratio between the sum of one loading time pr truck in the circuit and the complete net cycle time) and the shovel's efficiency, and by Hayes, Splaine and Whitaker {2}, who established this relation from a large number of observations in the Nchanga pit in Zambia. The present method establishes this relation by a straightforward calculation procedure. Theoretical solutions to some situations are found in the litterature on the queuing theory. The papers {3},{4} and {5} give solutions to situations, which fall outside those encountered in the shovel-trucks circuit. These solutions together with simulations of in-termediary situations have been used to establish an interpolation procedure for the correction factors to be applied to the waiting time formula in order to cover the situations encountered in practice.

Jan 1, 1977

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993