Search Documents

By Yehia El-Ibiary, M. P. Evans

One way of increasing conveyor systems productivity is by monitoring the key parameters in the systems. In this paper, a new line of smart bearings will be presented and discussed. The new bearings are capable of monitoring temperature, vibrations, and belt speed for early detection of potentially serious problems. The new smart bearings have built in sensors that are carefully integrated and protected for long life service. These bearings are going to be the key to increasing the up time of belt conveyors in the future.

Jan 1, 1996

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By Hyung-woo Kim, Sup Hong, Sung-Soo Kim, Chang-Ho Lee

A deep-seabed integrated mining system, which consists of four subsystems such as riser pipe, buffer, flexible riser, and tracked vehicles, is presented in Figure 1. In order to collect more manganese nodules, multiple tracked vehicle systems should be used in a deep-seabed integrated mining system.

Sep 1, 2014

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By Helen Leung, Colin R. Phillips

The performance of personal alpha dosimeters in mixed radon daughter and thoron daughter atmospheres in Ontario uranium mines is described together with monitoring developments which enable the radon daughter working level to be determined separately. The theoretical bases for continuous and integrated working level measurements based on individual and gross counts are presented in terms of the weighting factor for combining the thoron daughter working level with the radon daughter working level, and in terms of the in-growth time of the air. Implications for the determination of working level in the presence of thoron daughters are discussed.

Jan 1, 1981

By N. Dahotre, C. Blue, C. Zhao, B. Parekh, D. Tao, G. Engleman, R. Honaker

Equipment wear is one of the major concerns in screening of coal and minerals. Not only does it decrease the screen service life, it also results in inconsistent aperture sizes and deteriorates the efficiencies of downstream operations. In this research, a coating technique based on laser surface engineering (LSE) was successfully developed to increase the life span of raw coal screens. The microstructure and wear properties of the coating were investigated in this study. Enhanced wear resistance performance (up to 11-fold increase) of coated screens has been achieved in laboratory wear tests.

Jan 1, 2006

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

By Ted Budd, Vladimir Goubanov

The East Central Interceptor Sewer, commonly known as the ECIS Project, is the largest public works construction project awarded by the City of Los Angeles. The complexity of this $240 million project, together with the challenge created by the mandated 1,000 calendar days for construction completion, make this project a major interest for the tunneling industry. This paper will describe the ECIS tunnel project, currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor / Frontier-Kemper. Mining of the18.5 km (about 11 miles) long and 4.7 m (15ft-4in) diameter tunnel is underway with four Tunnel Boring Machines mining at the same time. Details on the mining machines, muck handling systems, innovative construction sequence, together with mining progress will be given.

Jan 1, 2003

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By A. Steinmüller

Introduction In the design and operation of gravity concentration circuits, the application of process models for spiral concentrators offers significant benefits. A substantial amount of work has been produced over the last 30 years in the field of modeling the metallurgical performance of spiral concentrators. It is not the aim of this contribution to add to the refinement of modeling technique but to share some of the experiences and potential improvements which can be achieved in a relatively simple way. The design of spiral circuits usually requires extensive testing. This is often conducted in batch operation only, either due to lack of suitable continuous testing facilities, the unavailability of sufficient quantities of sample, or other constraints. Typical problems arising during circuit development from batch testwork are the extrapolation of results to different feed conditions, and resolving of internal recycles. Model selection and development The classic approaches in spiral modeling technique range from fundamental fluid dynamics, based on the Navier-Stokes equations in combination with expressions for local slurry properties, to fully empirical and statistical models. With the initial objective of developing an in-house tool for gravity circuit optimization and development, mathematical model types from each category, available either commercially or in the published literature, were evaluated. Model selection For the desired purpose, an approach proposed by Holland-Batt (1990) was found suitable, which was adopted and modified. Holland-Batt reported that the shape of release curves in spiral applications could be described by a combination of a linear function in the initial recovery zone, and a power law function outside this zone. The proposed recovery function was formulated as

Jan 1, 2005

By D. G. Feuerbacher

Maximizing production of oil from sandstone petroleum reservoirs is aided by use of non-damaging drilling and workover/completion fluids. Various tests, such as X-ray diffraction, scanning electron microsccpy, petrographic microscopy, porosity and permeability are conducted on core samples. Several fluids are selected, on the basis of these results, for return permeability tests. A report is then written giving the results of all tests, potential reservoir problems, and recommended practices for exploiting the reservoir.

Jan 1, 1983

By Paul Higley

Specialty Devices, Inc. and the CMRET/NIUST, University of Mississippi, have collaborated in the design and development of a new class of Robotic Underwater Vehicle (ROV) focusing on efficient, low cost, deepwater operations. The need for such a vehicle was driven by special requirements encountered in the establishment of the Gulf of Mexico Gas Hydrates Research Observatory at a depth of 850m in Mississippi Canyon Block 118 on a restricted budget. Requirements included deployment and recovery of tools and sensors and the connection of underwater-mateable electric and fiber optic connectors at depth. The standard complement of equipment required included; high-resolution video with lighting, scanning sonar, robotic arm, precision positionin and thrusters for limited transit and maneuvering. Conventional deep water ROVs are lowered in a large cage with a buoyant tether between the cage and the ROV. The tether is wound on a winch in the cage deployed as the ROV swims out from the cage. This cage is lowered on a large diameter umbilical cable with strength elements and communications elements and conductors for electric power. With increasing water depth the umbilical cable must become ever larger to accommodate increased power transmission loads and strength demands, with corresponding increase in deck handling equipment size and in turn, vessel size and overall cost. The surface ship must include a dynamic positioning (DP) system to control ship propulsion to maintain the position of the ROV cage at a position relative to the sea floor. DP ships with this capability and the ability to carry the large umbilical cable and winch are expensive.

Jan 1, 2008

By Willaim A. Berg

Vegetative stabilization can help meet the esthetic objections and pollution problems posed by mine wastes. However, mine wastes are often unfavorable growth media and special treatments and techniques are needed for plant establishment and continued growth. The establishment of vegetation on mine wastes was the subject of many papers presented at the International Symposium on Ecology and Revegetation of Drastically Disturbed Areas held at Pennsylvania State University on August 3-16, 1969. This paper is a summary of those papers presented at the symposium that dealt with the nutritional and physical aspects of plant establishment on a variety of mine wastes. The synopsis presented is a combination of excerpts from the abstracts, notes on the oral presentations, and rough drafts of some of the papers. The papers will eventually be published in the symposium proceedings.

Jan 1, 1970

By H. W. Hitzrot

Introduction Mechanical classifiers consist of a settling tank with parallel sides and a sloping bottom equipped with a mechanism which continuously agitates the pulp and removes the settled solids. The functions served by mechanical classifiers include the following: (1) allow the particles larger than the desired size to settle in the tank and provide an overflow product with a minimum of oversize particles, (2) produce an overflow product of sufficiently high solids content to meet the requirements of the subsequent processing steps, (3) agitate the pulp and permit separation of the entrapped undersize particles so they can report in the overflow product, and (4) drain and remove the underflow solids from the settling pool. Various types of mechanisms have been used to agitate the pulp and remove the settled solids, which include: (I) endless belt and chain drags, (2) reciprocating rakes, (3) helical flights mounted on a rotating shaft which extends through the settling pool, (4) helical flights inside of a rotating drum which contains the classifier pool, (5) troughed conveyor belts forming the settling pool in the concave curve of the belt closely following the tail pulley, and (6) low-speed impellers agitating the underflow settled in the apex of cone-type mechanical classifiers.23 The principal use of mechanical classifiers has been in closed¬-circuit wet grinding; however, this application has been widely displaced over the past few decades by the hydrocyclone. The hydrocyclone installation, including its feed pump, offers lower capital costs and requires less floor space. Nominally it produces an overflow prod¬uct of higher solids content, compared with a mechanical classifier, for comparable classification size up to 400µm (35 mesh). However, these advantages of the hydrocyclone are being gained at the sacrifice of some of the advantages of the mechanical classifier. The mechanical classifier requires less power and has lower maintenance costs than the hydrocyclone and its feed pump. The underflow product from the mechanical classifier can have a higher solids content and contain less entrapped undersize particles than the comparable product from the hydrocyclone. Consequently, it is capable of operating at a higher classification efficiency. A reduced circulating load24, 25 results under these conditions in a closed-circuit grinding application. Other applications for mechanical classifiers include desliming, dewatering, and washing operations. Sand-slime separation may be achieved using one or more stages of mechanical classifiers. Typical applications would include washing and deslimining of concrete aggre¬gate or sand; glass sand; abrasives; oyster shells; phosphate rock; iron, nickel, and chromium ores; alumina; zeolites; solar salt; and precipitates from chemical processing. As an example for the latter, Bitzer26 recommended the use of mechanical classifiers for countercur¬rent cementation-in-pulp of copper from the leach liquor. Similarly, mechanical classifiers are used in uranium processing27 for separation of the barren sands from the pregnant leach solution. Depending on the particle size and the effectiveness of the sand¬slime separation, the sand product from mechanical classifiers may be drained to solids content approaching 84%. Thus, mechanical classifiers are frequently used as dewatering equipment for various applications, such as: 1) Make a product having suitable solids content for subsequent transport by belt conveyor. 2) Provide a drained product to reduce cost of drying. 3) Provide a drained, washed, heavy sand product for return to the circuit. 4) Recover fine values from dilute plant effluents from coal, sand, phosphate-rock, and iron-ore washing plants and from steel-mill flue¬dust scrubbers. 5) Drain residual reagents of a preceding process stage prior to conditioning with reagents of different characteristics, e.g., cationic¬anionic flotation of phosphate rock, iron ore, etc. Design and Operating Features The proper selection of mechanical classification equipment re¬quires that the properties of the solids and liquid are adequately de¬fined. The following descriptive information regarding the solids is desired: feed rate, chemical and physical composition, density, tem¬perature, size analysis, and desired separation size. For the liquid used, the following data would be needed: feed rate, density, viscosity, pH, and temperature. Settling Area. The pool area required to permit a particle larger than the separation size to settle depends on the density and shape of the particle and on the density and viscosity of the pulp within the classifier pool. These criteria of the solids and pulp determine the settling rate which, in turn, determines the settling area required. Determination of the settling rate by long-tube batch tests can be used to calculate the settling area. A theoretical approach for estimat¬ing the settling area requirements is discussed in Chapter 1, Classifica¬tion Theory. This procedure can be used when neither test data nor empirical data from similar operations are available. Data on settling-area requirements and settling rates have been compiled by the manufacturers of mechanical classifiers. The approxi¬mate settling area required for a particular separation size can be estimated by using the curve shown in Fig. 65. This curve applies for closed-circuit grinding applications. For dilute velocity classification in open circuit, desliming, the length of the overflow weir, W, multiplied by the weir&apos;s mean distance from the feed opening, E, is used as the design criterion, instead of the settling area, in sizing the classifier. The area requirements, W X E, for dilute velocity classification can be expressed in terms of volumetric flow, Q, and settling rate, Rs, as follows: W x E = Q/(18.06 Rs) where W and E are feet, Q is gallons per minute, and Rs is inches per second. Overflow Weir. The hydraulic head, and thus the velocity at which the overflow crests the overflow weir, is one of the factors controlling the particle size of classification. Consequently, the length of the overflow weir must be designed to provide the overflow velocity which allows the particles larger than the desired size of classification to settle in the working area of the pool. Obtaining the necessary

Jan 1, 1985

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999