Search Documents

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By J. C. Yingling, G. T. Lineberry

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will he intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder through flow to avoid production bottlenecks. Simulation studies suggest that the control strategy would be very effective in reducing capacity requirements of gathering belts.

Jan 1, 1993

By G. Norman Owen, Roger E. Scholl, Tor L. Brekke

INTRODUCTION Underground structures are generally regarded to be safer than surface structures during strong seismic motion, except when crossing a causative fault. Recent studies of observed earthquake damage to tunnels generally support this view, although instances of severe damage and, occasionally, collapse are reported. For proposed underground construction of sensitive structures such as nuclear power plants, liquefied natural gas facilities, and nuclear waste repositories, a verification of the seismic response of underground structures will be required.. This paper discusses the stabilization recommendations used in a study of additional costs required to protect tunnels against ground motion caused by earthquakes and underground nuclear explosions (1). The study is a part of the site investigations for possible construction of a nuclear waste repository. The additional costs estimated in the study are not presented here; only the stabilization measures are presented in the present paper. The tunnels, which would constitute the underground facilities of a possible repository, are assumed to be 5.5 m (18 ft) in diameter and to be located at a depth of 600 m (2,000 ft). Three candidate geological materials are considered: argillite (shale), granite, and tuff. Several peak ground accelerations are used: 0.3g, 0.5g, and 0.7g for earthquakes, and 0.5g, 0.7g, and 1.0g for underground nuclear explosions. Potential damage due only to shaking is considered here. This paper does not discuss problems that result from creep or sudden rupture of intersected faults or from ground failures at portals.

Jan 1, 1979

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By S. -Y. Hwang

An ongoing problem for industry in Korea is effective removal of heavy metals from and safe disposal of spent power plant fly ash. This research endeavor attempts to develop selective separation of Ni from leach liquor using a selective chemical precipitation method. The research was conducted by changing two variables, the pH and the concentration of ions in solution. The effect of other ions present in the system on the separation efficiency of Ni species was also investigated by adjusting OH and NH3 concentrations. In the pH range of 7-9, the chemical precipitation method produced a high yield of Ni by precipitation from the fly ash leach liquor.

Jan 1, 2010

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil&apos;s primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri&apos;s production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri&apos;s research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By A. J. Surtees, M. P. Evans

This paper discusses the development and application of sophisticated monitoring equipment used to measure the operating parameters of conveyor systems. With the radical reduction in price of computer hard- ware and software during the last decade and an associated increase in memory capacity, the concept of continuous conveyor monitor is now a reality. With this tool, the various problems normally encountered in large conveyor installations can now be avoided at an early stage. • The four main areas of application are: • Design verification • Hand-over certification • Preventative maintenance and increase of system availability Failure analysis The paper introduces the techniques used and gives examples where the service has been used.

Jan 1, 1996

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilise crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realise reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By G. A. Perry

Cyprus Sierrita is a major producer of copper and molybdnum from its Sierrita and Twin Buttes open pit mines south of Tucson, Arizona. Both pits were started in the late 60&apos;s and are in excess of 1500 feet in depth. Sierrita has utilized a Cat 992C Remote Controlled Loader since January 1993. The loader was justified to increase SAFETY and PROFITS at Sierrita. It has exceeded all expectations. As of June 1993, it had produced additional profits totaling more than $1,500,000.

Jan 1, 1994

By A. Raviprasad, B. Das

Copper ore from the Rakha Copper Concentrator (India) was successfully floated using LIX-65 NS as the collector. The beneficial role of this reagent was clearly demonstrated in hatch-flotation tests. From a feed containing around 1% Cu, it was possible in a single-stage flotation to obtain a 23.7% Cu concentrate with a recovery of more than 90%. The plant now uses rougher, scavenger and a two-stage cleaning process. The tests demonstrated that LIX-65 NS is superior to conventional xanthate for the recovery of copper from the Rakha ore.

Jan 1, 1997

By John K. Kellis

With the cost competitive nature of material mining, the ability to actively monitor the condition of the conveyor belt systems without personnel dedicated to that task is very desirable. This paper discusses the development of a conveyor belt condition monitoring system, which actively monitors the conveyor belt, without the need to install special antennas. A belt width map can be generated, as well as detection of three types of physical damages: (a) failure of mechanical fasteners, (b) reduction in belting strength due to reductions in competent belt width, and (c) longitudinal belt rips.

Jan 1, 2000

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By Ahmed I. A. Salama

This paper describes the development of computer density control for heavy media cyclone circuit at the Coal Research Laboratories of CANMET. The control objective is to reach and maintain the medium density set point in minimum time. A description of the mechanical components and instrumentation are presented. The control strategy and computer software are discussed. Testing and evaluation of the installed system are presented.

Jan 1, 1989

By David R. Kalasky

One of the primary areas of computer application in mine ventilation has been the analysis of mine ventilation networks. A variety of network analyzers that are aimed toward the solution of flows in a given network has been developed. These programs typically use the Hardy Cross or other iterative algorithm for solution of any network, even those that are complex. The computer software has become more efficient and sophisticated over time and has thus been widely adopted for ventilation network analysis. One of the shortcomings of these programs is that they have been developed with the idea of analyzing the ventilation requirements at a single point in the lifetime of a mine. This provides the ventilation engineer with an important tool for analysis but falls somewhat short of providing a convenient means to economically com- pare alternative methods for ventilating a mine. The program described in this paper provides such a tool. The principal concepts that were necessary for the completion of a computer program that analyzes ventilation alternatives is the capability of efficiently determining the ventilation requirements at a variety of times during the lifetime of the ventilation system and some method of analyzing the costs of the alternatives on a realistic comparative basis. To accomplish this task, the authors began using Penn State&apos;s mine ventilation simulator designated as PSU/MVS, Didyk et al. (1977a, 1977b) and added the necessary additional software to accommodate the need for multi-period, time-dependent analysis of the net- work. The software was then tested on a coal mine ventilation problem with a 23-year life. The problem points out the value of such a program for ventilation analysis.

Jan 1, 1986

By Clement K. Chase

Although flotation is the generally accepted process employed to recover gold and silver as well as copper, lead, and zinc from primary sulfide ores, the metallurgical requirements for the treatment of massive sulfide ore deposits differ markedly in many respects from those employed for the more common disseminated porphyry deposits. In Arizona, some properties classified as other then massive sulfide deposits because of mining and geological characteristics have produced mill-feeds similar to those from massive deposits. Several such occurrences are noted. The process requirements for massive sulfide deposits and unique mill-design implications are discussed in the perspective of world-wide economic considerations and the individual regional metallurgical and economic constraints in the United States.

Jan 1, 1986

By Jamal Rostami, Alireza Salimi, Christian Moormann

"Rock mass classification systems are often applied in many empirical design practices in rock engineering, some contrasting with the original intent and applications of these classification systems, for example, estimation of TBM performance in various ground conditions. While accurate estimation of machine performance is significantly impacted by rock mass properties, parameters used in many of the existing classifications are more related to ground support design and not rock mass boreablity. The results of many investigations on this issue have shown a weak correlation between TBM rate of penetration and rock mass classification. This limitation can be overcome by fine tuning the rock mass classification input parameters to represent influence of rock mass properties on TBM performance as has been the objective of RME or QTBM. This paper will offer an overview of the impact of rock mass on TBM performance and introduces an empirical equation for predicting performance of rock TBMs based on rock mass classification. The results of the preliminary analysis of a new model has revealed that the use of the proposed system can offer a reasonable accuracy for estimation of TBM performance in various rock masses. 1. INTRODUCTION Hard rock tunnel boring has become more or less the standard method of tunneling for tunnels of various sizes with lengths over 1.5–2 km. Estimating the performance of TBM is a vital phase in tunnel design, and for the choice of the most appropriate excavation machine. During the past three decades, numerous TBM performance prediction models for evaluation of TBM rate of penetration and advance been proposed. In brief, all the TBM performance prediction models can be divided into two distinguished approaches, namely theoretical and empirical ones (Rostami et al., 1996). The most common and recent works on this topic are summarized in Table 1. Currently, two models including Colorado School of Mines or CSM (Rostami and Ozdemir, 1993; Rostami, 1997) and Norwegian University of Science and Technology or NTNU (Blindheim, 1979; Bruland, 1998) models are the most recognized TBM performance prediction and prognosis models in use around the world."

Jan 1, 2016