Search Documents

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By S. S. Nadgauda, A. J. Hathaway

Typically, as long as the coal quality is within the specified range, electric utilities have used delivered cost of fuel per million Btu as the primary criteria for qualified coals when making coal-procurement decisions. Such an approach may not fully address the total cost of using different quality coals at a given plant. A practical and easy-to-build model is described for estimating plant-specific utilization costs for coals of different qualities. Examples are included to illustrate the modeling results for plants operated by two utilities. While the model has certain limitations, it does represent an improved method for evaluating coal bids, and, consequently, reducing generation costs.

Jan 1, 1990

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

By Hang Yang, Linneas W. Laage

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influence such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to the ventilation system. This paper describes recent USBM research to validate MFIRE's calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.

Jan 1, 1995

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

By J. G. Groppo

Hyperbaric filtration was evaluated at the laboratory scale for dewatering fine coal cleaned by froth flotation. A laboratory pressure filtration procedure is described to obtain uniform cake structure from dilute slurries containing a significant amount of coarse material. Baseline tests were conducted varying filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH to determine optimum operating conditions for eventual application on a continuous pilot scale hyperbaric filter.

Jan 1, 1994

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990

By John L. Habberstad, Robert R. Thompson, George B. Wallace, Robert C. Bates

INTRODUCTION Rock bolts are one of the most common mine support systems in use today with approximately 90 to 95 million used annually in the nation's coal, metal and non-metal mines. By far the largest majority of these are steel bolts with mechanical expansion shell anchors. Many theories have been advanced to explain the ground control achieved through the use of rock bolts. Most of the theories are applicable to a specific set of circumstances, geology, geometry, rock properties and in-situ stresses. Examples are those which relate the beam building or strata-hanging theories of ground support used in the rectangular openings of a coal mine(l). In tunneling and most metal mining, either circular or horseshoe shaped openings are normally used. Here, bolts may be used to develop a radial stress around the opening, which adds stability to that opening, or merely pin blocks of rock back into more stable ground so that they cannot slip. In most cases, the bolts are torqued to a specified value to seat the anchor and to achieve the pre-load or tension that is desired. To be effective, however, this tension cannot be lost through bolt slippage or creep frequently caused by blasting, moisture attack or raveling of the rock surrounding the drill hole, etc. Furthermore, in soft rock or in oversized holes, sufficient anchorage cannot be achieved with the mechanical anchor, and in very brittle rock the concentration of forces produced by the expanding anchor might cause a crack to propagate from one drill hole to the next. Mechanically anchored bolts are also short lived in mines or tunnels having a corrosive seepage. The steel in these installations can fail

Jan 1, 1974

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By J. J. Gusek

An 81 hectare (200 acre) tailings impoundment at a taconite operation in Wyoming that ceased operations in 1983 has been a source of blowing dust. The site qualified for reclamation under Wyoming's Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction included: incorporating commercially available organic amendments and fertilizers into a 300 mm (12 in) thick "cap" of a sterile clay loam cover material, lowering the water level in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin, constructing a wide tailings pond spillway that allows flood control while minimizing seasonal water level fluctuations in the pond, and building rock berms and rock snow fences for wind erosion control and soil moisture preservation. Tree planting in the protective wind/snow shadows of rock berms and rock snow fences, and the plugging of a decant pipe are planned for future work.

Jan 1, 1998

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

By Dirk van Zyl

Three conditions are required for a risk to be realized: (1) a source of risk (i.e., hazard) must exists (2) some process must take place which will lead to the exposure of people, animals, and/or the environment to the hazard: and (3) as a result of the expense, undesirable effects are produced on the people, animals, and/or the environment. A comprehensive risk assessment addresses all three of the conditions through the following four steps: (1) risk source (hazard) characterization, (2) exposure assessment, (3) dose-response assessment, and (4) risk estimation. Although the terminology may differ, the overall approach of financial, public health, and environmental risk assessments is the same (National Science Foundation, 1985).

Jan 1, 1988