Search Documents

By Christopher Haycocks

Self-supporting, open stoping underground mining methods are some of the earliest, starting with the prehistoric flint mines of Europe and the Egyptian gold mines of Nubia in the time of the pharaohs. When the early miner created an opening, it had to be inherently stable and self-supporting to enable him to continue. Therefore, as mining progressed beyond simple gophering, self-supported open stoping methods were devised to meet the needs of individual ore bodies. Timber for support appears in mines as early as 1000 BC, but this was for no more than local ground control. The ingenuity of mining engineers through history has so refined open stoping methods that today they produce more tonnage than any other mining system. Self-supported open stoping finds its application in moderate to strong rocks that exhibit little jointing or fiagmentation. Good back, hanging wall, and footwall conditions that require no more than incidental support are an essential part of these mining methods. Open stoping methods find applications in all inclinations of ore body from flat to vertical, and where ore movement may be either mechanical or under the influence of gravity. Table 18.0.1 demonstrates the range of ore bodies suitable for open stoping, with particular reference to their dip and the deposit thickness. Most of the flat-dipping applications use ore pillars for overall support and ground control that may be recovered under some conditions after completion of normal stoping practices. In steeper ore bodies, rib, crown, and sill pillars used to block out the ore may be recovered subsequent to the completion of stoping. Open stopes are frequently filled to facilitate pillar recovery. Two of the methods, vertical crater retreat (VCR) and shrinkage stoping, utilize fragmented ore for temporary support in the stopes. In these two cases, the stope is not strictly open until after drawdown.

Jan 1, 2008

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By Robert P. Bell, John T. Waggoner

The Metropolitan Water District of Southern California is designing new outlet facilities for Lake Mathews, including a junction shaft, connecting tunnels, and an ear-shore outlet tower. Since Lake Mathews must remain operational during construction, groundwater inflow potential is a concern. This paper describes the challenges and methods used to investigate rock mass and groundwater conditions at an operational reservoir, where offshore and onshore geotechnical exploration was performed. Several investigative and analytical methods were used to characterize rock mass and groundwater conditions, including rock coring, downhole geophysical and video surveys, hydraulic conductivity testing, automated groundwater level monitoring, and laboratory testing.

Jan 1, 1999

By E. D. Goddard, D. S. Murphy

Acid resistance, zeta potential and ESCA (electron spectroscopy. for chemical analysis) experiments were performed on emperador marble and four calcium carbonate samples (onyx calcite, travertine calcite, Iceland spar calcite and aragonite). Six fluorine-containing reagents were used to treat the surfaces of these materials: magnesium hexafluorosilicate, zinc hexafluorosilicate, sodium fluoride, zinc fluoride, strontium fluoride and stannous fluoride. The acid resistance of treated samples proved to be much higher than that of their untreated equivalents. The isoelectric point of treated samples approaches the isoelectric point of fluorite. Also, the fluorine content, as measured by ESCA, of a marble surface treated with magnesium hexafluorosilicate is much higher than that of an untreated sample. The binding energy off of fluorine and calcium the treated marble is consistent with the formation of calcium fluoride.

Jan 1, 1994

By Lynn I. Kelley

Industrial-mineral production contributes on the order of CDN$1.5 billion per year to the economy of Saskatchewan, Canada. Potash is the primary industrial mineral produced in the province, followed by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium-chloride brine, and "clinker." Potentially economic deposits of kaolin, diamond, and building stone are under evaluation. All of the major deposits of commodities discussed here are located south of lat 56°30'N. Most of the locations are presented on Figure 1 POTASH Saskatchewan supplies approximately 30% of the world's demand for potash. Eight conventional underground mines and two solution mines produced an all-time high of more than 13 million metric tonnes of potash (KC1) (8 million tonnes K2O equivalent) in 1997, valued at over CDN$1.4 billion. All of the mines exploit the middle Devonian Prairie Evaporite. The four potash-bearing members of the Prairie Evaporite underlie much of southern Saskatchewan and extend southward into North Dakota and Montana and east- ward into Manitoba (Fig. 2). Halite and anhydrite separate the potassic members. The evaporite beds locally are interrupted by solution structures (anomalous ground). Some of the structures may be related to deep-seated tectonic features.

Jan 1, 1999

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By Lindsey Schneider, Steve Kirk, Michael Miglioretti, Jeffrey P. Kolzow, Kyle White

The US17 Spring/Fishburne Drainage Improvements Project utilizes a stormwater conveyance tunnel system of approximately 8,250 LF. The tunnel system includes two intersecting tunnels of differing diameter at a 40-degree angle. The intersection was constructed in soft-ground conditions. This paper discusses the design, geotechnical concerns, initial ground support, and final lining construction. The tunnels utilized two soft-ground TBMs excavated at 15 ft and 11 ft with ribs & lagging initial support. The final lining consisted of unreinforced and reinforced cast-in-place concrete with polymer fibers. Concrete final lining was successfully completed in March 2020.

Jun 13, 2021

By Xinyang Yu

The flotation of diaspore, kaolinite, pyrophyllite, illite and the diaspore-kaolinite mixture were studied with a new cationic organosilicon quaternary ammonium collector entitled QAS222. The acting mechanism of the collector with the four minerals was analyzed by Zeta potential measurement and FT-IR spectrum analysis. The results indicate that the QAS222 was effective in the reverse flotation of the diaspore-bauxite mixture of different Al2O3 -to-SiO2 mass ratios (A/S ratio) at an optimum pulp pH of 11. The potentials of the four minerals increased when they were conditioned in the QAS222 solution; however, the potentials of the three aluminosilicate minerals increased faster than that of the diaspore, especially at pH>9. Furthermore, they were positive in a wide pH range, indicating that QAS222 has a strong adsorption on the surface of the aluminosilicate minerals and thus that these minerals can be floated. The FT-IR spectra analysis further indicates that, besides electrostatic adsorp-tions, formation of the hydrogen bond and ammonium absorptions, chemical adsorptions occur between QAS222 and the aluminosilicate minerals, which allow for the QAS222 to be strongly adsorbed on the aluminosilicate minerals. However, these reactions between QAS222 and diaspore at pulp pH=11 are weaker than those of the aluminosilicate minerals. Thus, surface adsorptions cannot be formed effectively, resulting in reduced floatability.

Jan 1, 2010

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By George C. Toland

Tailings disposal has been a problem for the mining engineer since the beginning of the metal milling process. Disposal systems in common use have evolved as the most economic method for the disposal of an unwanted waste material within the disposal restrictions in force at the time of construction. As restrictions are constantly being expanded, the design requirements for tailings disposal systems are also being enlarged. However, proper design will always be to provide the most economic disposal system that will meet current safety and pollution requirements. This paper presents a brief description of some of the design features of tailings disposal systems in common use and presents specific design features of the gypsum tailings disposal pond at Kimberley, British Columbia, owned and operated by Cominco Ltd.

Jan 1, 1971

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000