Search Documents

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

INTRODUCTION Conventional roof support methods such as mechanical and resin bolting provide adequate support for a wide variety of coal mine roof conditions. However, roof falls remain the single largest cause of death and injury in underground mines and seriously hamper production in many operations, demonstrating that these methods of roof support are not universally effective. One of the most recent and successful advances in coal mine roof control has been the introduction of the roof truss. Although past work on roof trusses (Gambrel1 and Haynes, 1970; Sheory, et al, 1973) shows little quantification of this support technique, numerous field examples have been cited where the truss effectively supported roof which could not be controlled by either mechanical or resin bolts (Kegel, 1969). The truss combines the advantages of both inclined roof bolts and post-stressing the roof. However, the full benefits of roof trusses will only be realized when design criteria to optimize support capacity are determined. The number of trusses required for a given roof condition can then be minimized, reducing installation time and making them economically more feasible. The purpose of this research is to develop roof truss design criteria based initially on laboratory studies of gravity-loaded multi-layered photoelastic mine models. Laboratory test results will then be modified where necessary following future field testing. The ensuing relationships should provide the field engineer with a reliable means of calculating optimum truss configuration, capacity, and spacing for a set of known roof conditions.

Jan 1, 1977

By C. E. Jordan

The Bureau of Mines conducted research to determine the effect of fine bubbles on the flotation of fine-sized particles (minus 20-um size). Turbulent flow collision models for fine particles and fine bubbles were reviewed. Velocity distributions within the flotation cell along with measured bubble and particle size distributions were considered in the models to predict the flotation response. The models were corroborated with laboratory fine-bubble flotation tests to verify the expected increase in flotation efficiency.

Jan 1, 1988

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercaptosilanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1992

By S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000 cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By N. L. Dorset, K. L. Heasley

Unfortunately, mining and mining accidents have gone hand-in-hand since man first started to extract ore from the ground. In the first published treatise on mining, De Re Metallica, Georgius Agricola (1556) stated that cold, water, dust, stagnant and foul air, roof falls, falls from ladders and demons all caused injury and death in the mines of his day. Although demons are no longer considered a cause of accidents in modern mining, the other factors remain with us still. The United States government started keeping track of fatalities with the establishment of the federal Bureau of Mines in 1910. Successor agencies, such as the U.S. Mine Safety and Health Administration (MSHA) continue to track fatalities today. Looking at the records, it can be seen that coal mine fatalities dropped from 2821 in 1910 to only 27 in 2004. The reduction in fatalities and injuries didn’t “just happen.” It took concentrated effort from the entire mining industry: miners, supervisors, safety officials, mining inspectors and mining researchers. But first, specific hazards must be identified before they can be corrected. In past, coal mining accidents have been analyzed by: type (roof fall, electrical, etc), mine attribute (location, seam height, etc.), and aspects of the mineworker (work experience, job classification, etc). Much of this research helped to direct the industry’s attention to where additional vigilance and safety training was needed. No doubt this directed effort has led, at least in part, to the decrease in coal mining fatalities. This paper takes a novel look at coal mining fatalities: it examines the risk of fatalities based on how long the mine has been open.

Jan 1, 2006

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By Williams R. Reynolds

Studies of the northeastern Mississippi bauxites were initiated primarily for the purpose of ascertaining the quality and quantity of the ore. Subsequently, this ore was found to have a rather dubious economic value as was previously suspected but never established in earlier economic reports (1, 2, 3). However, the quality of ore was found to be higher than previously thought. Even though the ore bodies were determined during the early stages of this study to be too thin, small and widespread for commercial production a continuation of the study was not abandoned. On the contrary, the present investigation was intensified concentrating less on the economic application and more on stratigraphy and genesis. Considering the ever increasing demand for aluminum products the northeastern Mississippi bauxite district which includes portions of Tippah, Benton, Pontotoc, and Union Counties may soon become, in spite of inferior quantities of ore, an attractive area for bauxite production. Presently, however, the meager quantity of ore discourages exploitation. On the other hand, these northeastern district bauxites are facies of more extensive units of lignite bearing high aluminum clays, and considering the advances in aluminum extraction from clay these clays may in the future beckon mining interest. The bauxite of the northeastern Mississippi district, mapped as a part of the Betheden Formation (4). has an outcrop trend along the county lines of Tippah and Benton Counties and the extreme western portion of Union and Pontotoc Counties. Studies of exposures and cores stratigraphically positions the outcrop between the middle Midway Porters Creek Clay and the lower Eocene Wilcox sands and

Jan 1, 1977

By Thomas G. Goonan

Copper production through smelting generates large volumes of material flows. As copper contained in ore becomes copper contained in concentrate to be fed into the smelting process, it leaves behind an altered landscape, sometimes mine waste, and always mill tailings. Copper concentrate, fluxing materials, fuels, oxygen, recyclables, scrap and water are in-puts to the process. Dust (recycled),gases — containing carbon dioxide(CO2) (dissipated) and sulfur dioxide (SO2) (mostly collected, transformed and sold) and slag (discarded or sold) — are among the significant process outputs. This article reports estimates of the flows of these input/output materials for a particular set of smelters studied in some countries. They include Chile (Altonorte, Caletones, Chagres, Chuquicamata, LasVentanas and Potrerillos), Japan(Naoshima, Onahama, Saganoseki,Tamano and Toyo), the United States(Garfield — Fig. 1 — Miami and Hayden) and Europe (Glogow I, Glogow II, Huelva, Norddeutscheand Ronnskar).

Jan 1, 2005

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By J. C. Adams

Although explosives constitute only a small portion of a mine's total cost, the relative success of each blast has a tremendous effect on subsequent activities such as excavation, crushing, and equipment maintenance. Beginning in January of 1993, tests were carried out to determine whether productivity could be improved by replacing standard ammonium nitrate fuel oil mixtures (ANFO) with a high density, high performance blasting agent. The study was carried out at gold mines, coal mines, and cement quarries in Nevada, California, Colorado, and New Mexico. A wide variety of rock types and blasting conditions were encountered. Results showed that at most operations productivity was sufficiently improved to more than offset the increase in explosives cost. This resulted in a net reduction in mining cost. This paper presents a summary of these results.

Jan 1, 1996

By D. Spindler

Pursuant to the Federal Surface Mining Act of 1977 and the Illinois Surface Mining Act of 1980, Illinois has adopted revegetation success standard regulations that include the Agricultural Land Productivity Formula. The Formula establishes yield goals and standards to measure the success of meeting yield goals for reclaimed prime farmlands. The formula compares the quality of the pre-mining soils in the permit area and the county, to the crop production achieved on the reclaimed permit area and the county crop yield in a given crop year. The regulations also specify acceptable crops, erosion control requirements and time frames for demonstrating success.

Jan 1, 1986

By Myles G. Hyams

A mining project is proposed for the state of Pahang, Malaysia. The proposal involves the mining of a sulphidic ore body and initial processing to form a sulphide concentrate which will be transported to a roaster/acid plant for the production of sulphuric acid. An outline is presented on the potential environmental impacts of the project which have been assessed by superimposing project infrastructure and processes on to the physical, biological and social environment during the early design and planning stage of the project. The potential impacts eliminated by engineering design and the techniques employed are presented. However, there are a number of potential impacts that require careful consideration and planning for long term management. These include surface water drainage, waste rock leachate, tailings disposal and the social environment. Environmental management designed to minimise or alleviate these impacts as a result of project implementation concludes the paper.

Jan 1, 1991

By W. G. Willson

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture re-absorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid fuel.

Jan 1, 1997

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By Nikhil C. Trivedi, Robert W. Hagemeyer

Despite the apparently unflattering term filler, this group of industrial materials has become an essential component of many industrial products with varying degrees of sophistication. Mineral fillers are, by definition, inert materials included in a composition for some useful purpose. Included in this broad category are asbestos, barite, bentonite, natural calcium carbonates (limestone), clays, diatomite, feldspar, micas, silica, talc, and other industrial minerals. Also included in this category are synthetic mineral- derived materials such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. Mineral fillers are included in compounds to accomplish a variety of final results. Inclusion of fillers modifies physical characteristics such as hardness, brittleness, impact strength, compressive strength, surface texture, fire resistance, softening point, and electrical conductivity. Depending upon the performance characteristics of the particular filler used and the quantity of the usage (i.e., percentage added), these materials can enhance the physical and optical properties, price-performance, and appearance of the finished products. These enhancements in properties of the finished compounds are the result of properties of the fillers including chemical activity, purity, hardness, particle size, particle shape, particle size distribution, surface structure, color, density, and refractive index. This chapter will review the general usage of fillers, the rationale for their use, trends, and economic factors influencing those trends. Major using industries will be examined in detail with extensive discussion of major fillers used in those industries. The reader is referred to the appropriate commodity chapter for specific information on deposits and processing for industrial minerals. All of these same filler materials have additional significant uses based on their chemical composition or other characteristics. Cross-references for these will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 5th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and synthetic) and their more important end uses.

Jan 1, 1994

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975