Search Documents

By Joseph K. Cavey

To accommodate the new Pier A expansion at BWI airport, a 1.8 m (6.0 ft)diameter stormwater pipe was constructed below active Runway 15R-33L. The jacked tunnel alignment runs east/west below the runway, and the depth the crown was 6.1 m(20 ft). Soil conditions consisted of very loose to medium sand and gravel, with some medium stiff clay and silt. Super Jet Grouting was selected as the ground treatment system, creating large diameter columns. All work was performed from the surface of the runway between the hours of 12 am and 6 am. Monitoring points along the tunnel in the grout zone indicated zero settlement during tunneling. Tunneling operations in front of and beyond the treatment zone experienced significant settlement. Super Jet Grouting in the treatment zone provided a low permeability continuous stable soilcrete that was readily mined while the runway remained in service.

Jan 1, 2003

By D. L. Petersen, C. R. Nelson, P. M. Bergson, B. K. Nelson

Membrane waterproofing systems in large tunnels cause the partial decoupling of the concrete liner from the rockbolted and shotcreted reinforced rockmass. This decoupling leads to a loose fit of the liner in the excavation when shrinkage from cooling and moisture loss occurs. This increases tensile stresses which require either the addition of reinforcing steel in excess of common European practice or the potential for liner cracking. Hot weather concrete placement and cold weather service conditions increase the magnitude of the problem, while creep of the rockmass reduces it. Contact grouting also reduces, but does not eliminate, the problem.

Jan 1, 1991

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

By J. M. Rotter, R. A. Lohnes, J. Y. Ooi

Reliable prediction of wall pressures in a coal silo demands careful characterization of the stress-strain properties of the coal. This paper describes the results of triaxial compression tests on a typical fine-ground coal used in power generation and describes the fitting of several different constitutive models to the data. The fitted parameters for the constitutive models are well suited to application infinite element analyses. The different models are used to give the reader flexibility in choosing a model and to show the shortcomings of some models. To explore the quality of the fitting process, the fitted results are compared with finite element predictions of the triaxial test itself.

Jan 1, 1998

By J. H. Ahn, J. E. Gebhardt, W. K. Tolley

Color measurements were made for pure minerals, mineral mixtures and flolation froths loaded with different minerals. The research objective eras to correlate color with the composition of mineral streams. An industrially available system consisting of a fiber-optic-based illuminator and detector was used to measure color. The color values of binary mineral mixtures varied according to the type and proportion of minerals in the mixture. The measured color values of mineralized froths in the laboratory and in a commercial flotation circuit were dependent on the amount and type of minerals present.

Jan 1, 1994

By C. L. Schneider, R. P. King

Size distributions and liberation spectra were measured in samples taken from 10 streams in a taconite milling circuit under normal operating conditions. The size distributions were deter- mined by sieving and the liberation spectra by image analysis using the linear-intercept method with proper stereological correction. The measured data were used to validate a simulation of the milling circuit using MODSIM which included the calculation of both size distributions and liberation spectra. Both the measured data and the simulator showed that liberated magnetite was returned to the mill in the cyclone underflow. The simulation will be used to improve the economic performance of the plant.

Jan 1, 1995

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By C. W. Nelson, A. G. Moody

This paper describes the design, equipment selection and onshore fabrication of the largest facilities module ever installed in a single lift in the Gulf of Mexico. Measuring 35.5 x 70.1 x 21.3 m (110 x 230 x 70 ft), the three operating level structure houses Frasch process sulfur mining equipment and weighed nearly 49 million N (5500 tons) during lift. An operating weight of over 74 million N (8300 st) combines with bridge reactions acting on the in-place module and results in a total operating vertical load on the supporting platform deck of about 107 million N (12,000 tons). A Vierendeel truss structural system was selected for framing the module to allow maximum equipment access and routing flexibility for complex, insulated large diameter process piping. Research and finite element analysis of crimp plate siding behavior in shear was carried out during selection of siding type for the module. An interactive design sequence was carried out that incorporated in-place operational criteria, onshore fabrication considerations, complex process equipment requirements, plus load-out, ocean transport and offshore lift analyses. Project schedule dictated that design, procurement and fabrication be fast-tracked with parallel activities accelerated to the maximum extent possible. Design and construction of this largest and most complex module was done concurrently with 52 other components of the project including jackets, decks, process and living quarters modules as well as two 122 x 22 m (400 x 72 ft) sulfur tankers. Total tonnage of steel structures for the project exceeded 90.7 kt (100,000 st). The 5 kt (5500 st) mining module proved the viability and costeffectiveness of larger modules than commonly used in Gulf of Mexico waters. This technical advance can be matched with economic opportunity for other large-scale offshore installations.

Jan 1, 1994

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By R. A. Metz, Ted H. Eyde, Dan T. Eyde

Industrial minerals deposits present sampling and grade control problems not normally encountered in metal mining operations. No longer are industrial minerals simply crude ground mineral products but are in fact high purity chemical raw materials. Operators of industrial minerals mines and processing plants now must meet increasingly stringent specifications established by the consumer of the final products. Meeting these stringent specifications requires not only sophisticated processing techniques but equally important careful sampling and grade or quality control at the mine. A well-trained geological staff can assure an adequate supply of uniformily high quality feed to the processing plant. In the final analysis this results in significantly higher operating profits.

Jan 1, 1992

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Joseph F. Peters

The paper will begin with the physical parameters of design in a wire saw. These will include such things as the type of wire used, abrasives, horsepower of operation, and drive components. It will then go into the many uses of wire sawing in the quarrying and finishing of granite. This will include a step by step program of the removal of a block unit of granite from the quarry site through the finished slabbing and jointing in the plant. After this, there will be a small insertion of possibilities of wire sawing techniques in underground excavation work. This would be speculative only. I will use the example of powerhouse type of excavation work given to me by Dr. John Reed, and try to explain how I would attack this type of work using wire saws. Several slides of both design criteria and actual installations were shown.

Jan 1, 1997

By P. G. Tzeferis

Factory beet molasses media were used as cheap sources of sucrose for microbial leaching of Greek nickeliferrous laterites using strains of Penicillium and Aspergillus sp. Nickel recoveries of up to 62% and cobalt recoveries of up to 50% were obtained by leaching in a two-phase system in which bioacids were produced by fungal metabolism in molasses ferrocyanide pretreated media. The addition of potassium ferrocyanide to the molasses substrates prior to leaching was found to have a beneficial effect by increasing the level of citric acid bioproduction, thus improving the leaching efficiency of the fermentation liquid. The metals known to interfere with citric acid production (i.e., Fe, Cu, Ca and Mn) were those most efficiently precipitated. Considering the much lower commercial price of molasses in the industrial market compared to sucrose and glucose carbohydrate media, molasses could prove to be a promising alternative, despite the cost of the required pretreatment.

Jan 1, 1995

By M. Liu

The use of surfactants shows great potential for the removal of hydrophobic organics from soils by in-situ washing techniques. Lab-scale soil washing experiments were performed using sodium dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that the solubility of anthracene increases linearly with an increase in SDS concentration above the critical micellar concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1993

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By F. L. Wilke

Truck haulage costs form a major part of the total mining costs in hard rock open pit, mining operations. In order to minimize these costs one has to - determine the optimal truck fleet (type, size and number of trucks), and. simultaneously - determine the optimal organization of running the haulage system, i.e. especially select the optimal dispatching strategy in order to ensure maximal utilization of the trucks, and simultaneously - establish a reliable maintenance and servicing system to guarantee maximal availability.

Jan 1, 1982

By K. J. Shoop, S. J. Ripke, T. C. Rao, T. C. Eisele

This study investigated the use of a 7.6-cm inside diameter, 344.2-cm-tall horizontally baffled column to reduce the ash content of a low-sulfur bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage and feed quality. The tests were also carried out to compare the columns performance to a conventional column installation in an operating plant. In this paper, the results of this investigation are reviewed and discussed.

Jan 1, 1999