Search Documents

By W. Setzepfandt, J. Henneke

PREFACE Debris disposal can very often be a severe problem and major restriction on tunnel boring projects, especially for small diameter tunnels and in underground mines. Hydraulic transport could provide a suitable solution. Investigations have therefore been made in connection with a full-scale project of 4.8 km length and 2,3 m diameter, to obtain the required technical and economical data for planning an optimized transport system, e.g. for a tunnel boring drivage of 6 - 7 m diameter in underground coal mines. INTRODUCTION The Radau-Tunnel, chosen for the investigations, has been designed for transferring flood peaks between the rivers Radau and Grosse Romke in the Harz-Mountain of Lower Saxony. A DEMAG TVM 20/23 H tunnel boring machine was used to drive the tunnel on a rising gradient of 0,53 %. The rock consisted of shale and hornblende (55 %), granite (15 %), diabase (15 %), chert (8 %) and gabbro (7 %). The project has been sponsored by the Federal Ministry of Research and Technology.

Jan 1, 1981

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Gary J. Goldberg

Through the early 1980s, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation was made of total station systems and their ability to meet the surveying requirements of Bingham Canyon. This culminated in the purchase of a total station system as the mine reopened in 1986. The surveying department at Bingham Canyon during the early 1980s consisted of three, four-man crews using theodolites and self-leveling levels to perform the majority of the field work. Office work involved data reduction and hand plotting. Although hand-held programmable calculators were used, a great deal of time was spent manually transferring field notes to final calculations. After shutting down in early 1985, plans for start-up of mining operations in 1986 included a review of all aspects of the operation for cost and productivity improvement. Applying total station survey capabilities offered the potential to improve surveying accuracy and speed while reducing manpower needs.

Jan 1, 1990

By Jim Weeks

In July 1986, the United Mine Workers of America (UMWA) asked Secretary of Labor William Brock to form an advisory committee to advise the Mine Safety and Health Administration (MSHA) on rules and regulations concerning the use of diesel powered equipment in underground coal mines. The request was made under the Mine Health and Safety Acts of 1969 and 1977. The union's principal concern was with the chronic and acute health effects of breathing diesel exhaust. In July 1988, the advisory committee recommended that MSHA promulgate a variety of health and safety regulations. It also concluded that diesel particulate matter should be considered carcinogenic (MSHA, 1988). Now, seven years later, there are nearly twice as many pieces of diesel powered equipment in underground coal mines. MSHA, however, has not promulgated a single regulation to govern the use of this equipment. MSHA must fulfill its public responsibility to protect the health of miners. Regulations that take account of the considerable body of knowledge concerning these health effects must be a top priority of the incoming assistant secretary of labor for MSHA.

Jan 1, 1993

By K. G. Thomas

New developments in gold exploitation over the past few decades have been extensive and promise to be exciting for the foreseeable future. They cover all phases of gold mining from developments in mining, processing, computer and finance. This presentation will cover these different disciplines and show how Barrick Gold Corporation ("Barrick") has used these devel­opments to enhance shareholder wealth. The developments can be grouped into disciplines as shown in the following table.

Jan 1, 1996

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By K. N. (Mani) Subramanian

A 2.5 meter diameter column has been successfully used in a 100 tph flotation plant at the Harbour Lights Mine in Leonora, Western Australia, to produce a final gold bearing sulfide concentrate from the ore in a single stage. This pioneering application of column flotation cells to rougher stage was pilot tested using a 11 cm column, which demonstrated column's capability in rougher, scavenger and cleaner flotation stages. A hybrid circuit involving columns and mechanically agitated flotation cell s was adopted for the commercial installation. This paper describes pilot plant results, design of the plant flotation circuit, and early results of commercial operation.

Jan 1, 1988

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By Erland A. Tillman

The U.S. National Committee on Tunneling Technology under the aegis of the National Academy of Sciences has long recognized that productivity in major underground construction projects could be increased through better contracting practices and better management. Between 1974 and 1978, this Committee has prepared three reports on these subjects. This paper reviews these reports and their recommendations. It covers the extensive actions by the U.S. National Committee on Tunneling Technology to bring the recommendations to the attention of leaders in the underground construction industry and thus further their adoption and implementation. These activities are continuing. Visibility in this session will give these reports and recommendations increased exposure.

Jan 1, 1981

By J. H. Lammers, John Turney

The Eskay Creek Project was interesting in many respects, includ­ing extremely high grade of precious metals, refractory nature of the ore, carbonaceous content of ore resulting in preg robbing, and high content of many heavy metal sulfides in addition to the usual iron sulfides. Although the process plant was never constructed, extensive testwork was conducted and a flowsheet for the treat­ment of the effluent form pressure oxidation was developed as a basic engineering package. The flowsheet included removal of iron and gypsum by neutralization, selective recovery of copper by zinc precipitation, and recovery of zinc by solvent extraction and electrowinning. The zinc recovery produced a significant impact on the project economics. The waste water from the process met the environmental requirements for British Columbia.

Jan 1, 1996

By F. Forbes

For many years, the Machinery Division of Dravo Corporation has been designing and constructing bins and hunkers as part of overall plant facilities. We have designed bins to handle a variety of materials including coal, coke, iron ores and concentrates, sintered and pelletized ores, calcined and raw limestone, bentonite, alloys for BOF shops, and even cast iron chips from machining operations. We, along with everyone else in this business, have had our bin problems. The bins either plug, rathole, segregate, wear out, flood the discharge device, or overload it. Surprisingly, sometimes they have worked. As engineers, it has long concerned us that something as important as bin design should be so imprecise and that it has been so conspicuously avoided in research and in literature. In past years, rule-of-thumb design criteria had been to keep the sides of the bins as steep as possible and the outlets of the bin as large as possible. This criteria led to the design of bins with 600 to 700 side slopes and table feeders which were very large. Unfortunately, this meant trying to fit tall, skinny bins into a layout where minimum building height was required for obvious economic reasons. Like everyone else in the industry, we found that this design procedure was expensive and ineffective.

Jan 1, 1968

By Pat Gochnour, Jim V. Rouse

Advances in the design and construction of heap­leach pads and process plants have greatly reduced. the potential for accidental releases of process olut1on. While workers in the field, and regulatory agencies such as the EPA have long recognized that the potential effects of any spills would be short term in nature due to cyanide attenuation and degradation (Engineering-Science, September, 1986, Pyrih, 1990, Rouse and Pyrih, 198, Rouse and Pyrih, 1991 ), unfortunately the general pubhc has held a perception that such a spill would be an environmental catastrophe. Few factual data on actual accidental releases have been available to dispel such a concept. Such data now exist and shoul? be disseminated to show that prompt response, using a combination of chemical oxidation, natural attenuation, and enhanced biodegradation of cyanide, can limit the effects of such rare releases, in both time and space.

Jan 1, 1992

By Lennart Mukka

This paper describes the experiences from construction of a new ventilation system in LKABs Kiruna Mine in Sweden as well as the choice of the method for air flow regulation with concern of life cycle cost and the description of the foundation design. The evaluation of the performance test will be presented.

Jan 1, 1997

By Edward C. Spalding

The mineral estate of Arizona's State Trust lands, which are administered by the State Land Department for the benefit of the common schools and 14 other beneficiaries, totals more than 10.5 million acres, or almost 15 percent of the State's entire area. Trust lands exist in all 15 of the State's counties, with the most and least acreage found in Yavapai and Gila Counties, respectively. Revenues derived from the Trust mineral estate include royalties, rentals, and fees. In Fiscal Year 1983-84, these revenues amounted to $4.2 million, or 13.5 percent of all income received by the Trust during this period. Industrial minerals, led by sand and gravel, contributed $1.1 million from 82 active properties.

Jan 1, 1987

By J. Vaino Huhta

An exploration program which covered an area of about 17 000 km2(6564 sq miles), was carried out between 1966 and 1969 by the United Nations project named "Mineral Survey of the Azuero Area." The target became Cerro Petaquilla, Province of Colon, Panama. See Fig. 1. Regional exploration led to discoveries of many geochemical anomalies and minor mineralization, but it was only toward the end of the project that a promising target was indicated by a large zone of comer and molybdenum anomalies in stream sediments in a remote 1, area between the Cordillera and the Caribbean coast. Follow-up surveys established the presence of porphyry-type copper mineralization in the area now known as Cerro Petaquilla.

Jan 1, 1991

By A. C. Noble

Ore reserves are often less than 30% of the geologic resource estimates initially prepared by exploration geologists. Differences of this magnitude can lead to serious problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves but are later found to be misleading and gross overstatements of the actual ore tonnages. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery and economics early in the project and by using appropriate qualifiers in the resource statement. Examples using typical deposit characteristics are used to demonstrate how the cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1994

By D. D. Harbuck

Previous studies at the US Bureau of Mines (USBM) have shown that only 70% to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the USBM developed and researched the hypothesis that minor amounts of germanium and zinc silicate, present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of formed silica gel increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1994

By S. Chander

The fundamentals of flotation are reviewed with an objective to understand the limitations in predicting the performance of a sulfide mineral flotation system and in its scale-up from laboratory studies to plant practice. The difficulties can often be traced back to complex interactions between chemical and physical parameters and nonequilibrium effects. The physical and chemical changes that occur during the long sojourn of sulfide minerals that begins with mining, continues through crushing and grinding, and ends when they emerge from the flotation cell as a concentrate, are reviewed. The benefits of new techniques that have become available in recent years to identify and estimate the amount of surface species are discussed.

Jan 1, 1999

By Frederick W. DeVries

EPA announced, when they proposed to set a potable-water limit on cyanide, in August, 1990, that they had never encountered cyanide in a :sample of potable water, but they felt this was a sufficiently toxic and common material that it should be covered with a specification. The writer worked with both the American Mining Congress and the Aluminum Association in responding to their proposed spec. of 0.2 ppm max. of "cyanide" in· potable water. Although there are many subcategories of "cyanide", they failed to specify which type they meant.

Jan 1, 1993