Search Documents

By Victor J. Scaravilli, C. Richard Linamen

This paper presents a case history of Southwest Interceptor Contract No. 1, Cleveland, Ohio. It details some of the problems and solutions of handling and erecting precast concrete segments in a small bore soft ground tunnel. It also reviews how specific interpretations of contract requirements and contract administration effect production, performance and productivity.

Jan 1, 1987

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

By Bruce E. Holbein, Dennis K. Kidby, Ann L. Huber

World gold production figures and the processes used for gold production indicate a high dependence on both cyanide leaching and carbon adsorption metallurgies. Problems associated with the use of carbon in the treatment of refractory ores as well as economic and environmental considerations associated with the use of cyanide point to the advantages that can be realized through the use of more efficient gold adsorption media and with cyanide recovery. We have developed a process termed AurosaveTM-1 which provides a number of advantages through the use of a new synthetic robust gold adsorption medium, termed Vitrokele TM V-911. This process allows further recovery of gold from a variety of ores and allows for a simplified process for use not involving thermal regeneration or high pressure elution. We have also developed a cyanide recovery process termed Cyanosave ™ which uses Vitrokele TM V-911 and allows efficient recovery of cyanides from decants or tailings and re-use of recovered cyanide. This obviates the high chemical expenses for cyanide destruction where environmental issues require such water and tailings management.

Jan 1, 1998

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986

By J. Ainsworth, W. Trudel, L. Schutz, C. L. Bolin

Newmont mine geologists have added substantial economic value developing over 1,150 tonnes into quality surface and underground gold reserves since 1986. However, the recent 5-year gold price slump from $387 to $262 per ounce has shifted mine geologists focus to optimizing open pit profitability and developing high-grade, high cash flow and low capital development underground reserves. More than $65 million projected revenue has been added to the Gold Quarry south layback following multi-departmental model reconciliation investigations. Kriged mine polygon construction, controlled blast heave and high-quality geologic advice in selective mining will have multi-million dollar beneficial impacts.

Jan 1, 2002

By J. J. Moore, B. Mishra, D. L. Olson

The production of radioactive and reactive metals, such as plutonium, uses various pyrometallurgical techniques that generate significant quantities of waste salts contaminated with hazardous, reactive or radioactive materials. Health concerns, environmental regulations and economic considerations require proper mitigation processes to recover the valuable components and for recycling or unrestricted release of these salts. The Oxygen Sparging Process converts soluble metal halides, such as chromium-, plutonium-, cerium chlorides, into insoluble oxides and/or oxychlorides which can be consolidated and separated for long-term storage or further processing. The matrix salt phase, viz. calcium and/or alkali chlorides, are clean after oxygen sparging and fit for recycling. This method has been described and its optimized parameters discussed to show that RCRA regulated elements, such as, chromium, lead, cadmium, etc. report to the consolidated phase making the salt recyclable. Salt Scrub Reduction Process for the recovery of radioactive and RCRA metals from the waste salts has been developed. The process uses a Ca-Ga intermetallic alloy which recovers over 98 percent of the reactive metals. The matrix salt phase in this process, viz. calcium or alkali metal chlorides, are clean after salt scrub reduction.

Jan 1, 1995

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

The tungsten carbide insert bit has probably advanced blasthole drilling more than any other single improvement. Tungsten carbide inserts have longer life, maintain sharper edges, and penetrate faster than hardened steel edge bits. Before the tungsten carbide hit appeared, all-steel bits were used. Even with the new bits, blasthole drilling costs vary with the type of equipment used and its condition; the hole's length and diameter; the rock's texture, hardness, and nature; the operator efficiency. To help reduce drilling costs, the operator should be familiar with the use and care of drill bits. This article provides information about tungsten carbide rock bits used for percussion drilling. Consideration of tungsten carbide rock bits includes looking at bit materials [ ] as well as bit operation and maintenance. Two basic tungsten carbide rock hits are the button bit and the four-wing carbide insert bit. Three common hit-to-drill-steel connections are the bottom drive, tapered drive, and shoulder drive. Bottom drive bits arc typically used for singlepass or longhole drilling, with all percussion drills from handheld sinkers to heavy track drills. Tapered socket bits are available with shallow or deep carhide inserts, for the lowest cost depending on the rock type being drilled. Shoulder drive bits are available in all-steel or carbide insert design.

Jan 12, 1981

By Philippe Dumont

Presentation of the project Underground civil works to be performed They include two single track running tunnels and a service tunnel of a length of fifty kilometers . Many cross adits (180 adits) : to link the tunnels (53 cross passages), to relieve air super pressure from one tunnel to the other (87 piston ducts), to install technical adits (40 electrical rooms). Two cross-overs located at one third of the whole length, allow trains to shunt from one tunnel to the other so as to ensure one way traffic in case of emergency. Pumping stations allow water to be collected at the lowest point and pumped out. 1 Main features of the tunnels 1.1 The service tunnel This 4.8 m inner diameter gallery allows During civil works - front probing operations of the geological layers encountered (front and vertical probes). - lateral soil grouting that may be necessary to facilitate the boring of the two running tunnels . During operations - Maintenance and safety vehicles traffic - Fresh air supply to running tunnels - Fire protection and drainage system - Electricity supply and control and communication. The service tunnel has been bored with a 5.72 meter external diameter Robbins TBM for the undersea section, and a MITSUBISHI TBM for the land section.

Jan 1, 1991

By Priscilla P. Nelson, Steven D. Glaser, Thomas D. Rourke, O&apos

Construction records from six projects which employed full-face TBMs to drive 18 km of tunnel in sedimentary rock have been analyzed. More than twenty individual causes of delay could be identified. Delay causes are characterized on the basis of frequency and duration of incidents. Average utilization and downtime distributions are presented for each project, and frequency distributions of downtime per shift are discussed.

Jan 1, 1985

Mine managers need useful data to support production and maintenance decisions; for example, to evaluate the performance of replacement components. Today, managers rely solely on past experience, supervisors, opinions, and time studies. Our paper describes the concepts and algorithms we are developing for an automatic, intelligent decision support system (IDSS) that will aid managers by reducing and analyzing large amounts of, monitoring system sensor data and report only key production and maintenance information.. IDSS contains a pattern recognition, subsystem (IDSS/PRS) prototype to report graphical trends in traditional time study elements. We are designing. and prototyping a knowledge representation subsystem, using Knowledge Craft Tools, that will learn and adapt to the dynamic mine environment and reason about the recognized patterns using representations of manager's knowledge, equipment, capabilities, and mine layout and operating procedures. This subsystem will reduce, large quantities of time study type information to key issues that interest different managers.

Jan 1, 1989

By Burt Ensley, Viatcheslav Dushenkov, Ilya Raskin, David E. Salt

Roots of many hydroponically grown terrestrial plants, including sunflower (Helianthus annuus L.) effectively remove toxic metals such as Cu+2, Cd+2, Cr+6, Ni+2, Pb+2 and Zn+2 2 from aqueous solutions. It should be possible to scale up this process such that plant roots can be used to treat large volume aqueous waste streams. It can be extrapolated from laboratory results that to reduce the Cd concentration in a waste stream, from 1 ppm to below 4 ppb, with a flow rate of 4000 L/min, would require 3500 sq. m of plant roots with a density 5 kg fresh weight per sq. m. These results suggest that the roots of hydroponically grown terrestrial plants may provide an attractive alternative to the accepted water treatment technologies.

Jan 1, 1995

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993

By J. Muir

This report focuses on minimum ore block sizes that are economically feasible to mine with the vertical crater retreat (VCR) method. In 1985, Homestake Mining Co. began a program to bring several small block VCR stopes on line. This report examines these experimental stopes, including design parameters, ground control, drill patterns, secondary blasting, and mucking. Cost and scheduling comparisons are made with mechanized cut-and-fill and open cut- and-fill methods.

Jan 1, 1987

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991