Search Documents

Maximizing margins in competitive markets demands superior productivity. Unfortunately, management systems developed early this century for other industries often drive counterproductive behaviors choking mining productivity. Many executives and managers waste valuable time and effort relying on simply training and communicating to improve managerial practices and attitudes. In covering practical human behaviour, the paper explains why this fails -and explains how to use systems to successfully drive improved managerial practices and attitudes. It highlights use of modern performance Measurement, Analysis and Reporting systems to drive behaviors and improve margins -without capital investment -and make executive and managerial work easier and more effective.

Jan 1, 1999

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.

By John H. Clark

This paper outlines new technological improvements in underground trackless equipment for the metal mining industry with emphasis on maintenance related developments for Load Haul Dump machines. Also new developments on other types of equipment are covered including drills, road headers and electric LHD's.

Jan 1, 1983

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By Miroslaw M. Hajdasinski

A project's rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By H. A. Zollinger

The Hallmark Distribution Center is one of the most sophisticated material handling and order filling facilities in the world. The 53 million cubic foot facility houses an ultra-modern, computer- monitored distribution complex that handles as many as 1/4 million orders per day. The Distribution Center replaces 16 leased buildings scattered through- out metropolitan Kansas City and, in addition, re-leased 4 floors in mid-town Kansas City needed for creative and administrative expansion. This new facility is the nerve center for distribution of Hallmark products in United States and Latin America. The size and gross numbers of all parts of the system is a significant accomplishment, but the purpose of this paper is to explain the technical advancements in the state-of-the-art of material handling and controls. The system iteself is made up of seven sub-systems including receiving, warehousing, picking rack stocking, towline, order filling, order sorting, and shipping. Significant techniques were used in each of these areas as well as technical advancements in the state-of-the- art. The most significant points are in 4 of the areas and are discussed in this paper.

Jan 1, 1973

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986