Search Documents

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By W. A. Haley

Wheel loaders were first introduced shortly after World War II as small machines designed for handling loose materials in various industrial and processing applications. It was not until the early 1950?s, however, that machine size permitted widespread loading of loose or stockpiled material into on-highway type trucks. An ever increasing number of machines continue to be used for this purpose today. In fact, it is by far the major use for wheel loaders in mining and quarrying. Many of these loaders were working at mines or quarries handling in-process or finished material and some were doing shovel clean-up. It was quite natural then, when the primary pit loading shovel was down, to attempt to maintain some production by replacing it temporarily with the wheel loaders. Most of these attempts were not very successful, however, until the really large wheel loaders, 4- to 6-yd. size were introduced in the early 1960's. Since that time these machines have proven they can be productive and economical primary pit loading tools, a job that was once the exclusive domain of the power shovel. To be competitive with the shovel however, conditions must exist or be made to exist, that will be favorable for the wheel loader.

Jan 1, 1967

By Robert Stefanko

The most perplexing problem that has confronted mining engineers since the dawn of mining has been strata control. For the purposes of this paper, strata control will be defined as control of ground in the immediate area surrounding the, mine opening. To prevent movement of the surrounding strata into underground mine openings, miners have traditionally relied upon some type of artificial supports placed within the openings and located in a manner determined by trial and error from previous experience. Without the means to measure changes of stress in the supports and within the mine structure itself, an evaluation of the efficiency of the supports and mining system was impossible. Strata control thus remained an art with very little application of science. During recent years a revolution has occurred in mining. The modern mining engineer is contented no longer-with trial and error methods but is utilizing all the technological information at his command to obtain a solution to this age old problem. However, serious problems have arisen due to the lack of certain basic knowledge in three important areas: 1, The original stress distribution within the earth strata prior to mining. 2, Redistribution and concentration of the original stresses with mining activity. 3. The properties of rock that are significant in failure and its prevention.

Jan 1, 1960

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By Gale F. Hoffnagle

INTRODUCTION On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. These Amendments cover many aspects of air pollution control. The provisions which seek to control emissions of "air toxics" may, however, be the most far-reaching and will potentially have the greatest effect on American industry. The Administration has estimated that by the year 2005 industry will be spending $6.7 billion per year on air toxics control. Meanwhile, the Business Round Table has estimated that the price will be far higher, up to $62 billion per year, depending on how EPA and the States implement the program. BASIC REQUIREMENTS Any "major" source of emissions of 189 air toxics will be required to install "MACT." The translation of this statement requires some definitions: •MAJOR SOURCE - A facility (a contiguous property under single ownership and control) which has actual emissions of 10 tons or more per year of any single one of the air toxics or 25 tons per year of any combination of air toxics. •AIR TOXICS - Congress has provided a list of the 189 chemicals on this list. Those that may be important to the mining industry are shown on Table 1. This list can be changed by petition or by EPA. •MACT - Maximum Achievable Control Technology is to be defined by EPA for each industrial source category. EPA says there are about 400 categories. The Act defines MACT as: "the average emission limit achieved by the best performing 12% of the existing sources ... for categories with 30 sources or more" or, "the average emission limitation achieved by the best performing 5 sources in the category." TABLE 1 SELECTED AIR TOXICS FROM CLEAN AIR ACT LIST IMPORTANT TO MINING INDUSTRY Antimony Compounds Arsenic compounds (inorganic including arsenic)' Beryllium Compounds' Cadmium Compounds Chromium Compounds Colbalt Compounds Cyanide Compounds (dissociation compounds) Lead Compounds' Manganese Compounds Mercury Compounds' Fine Mineral Fibers Nickel Compounds Radionuclides (including radon)1 Selenium Compounds 1Previously listed under NESHAP 2The Administration may not list elemental lead as a hazardous air pollutant.

Jan 1, 1991

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By T. J. Jr. Corwin

This paper will cover the problems confronting an owner when planning and estimating the cost of a proposed tunnel. Three factors are known: the length, size and the time allocated for the completion of the work. In general the difficulties encountered when driving a tunnel in California are the greatest at the lower elevations and in the Coast Range and are minimal in the Sierra Nevada mountains particularly in granitic formation. The writer will discuss the experience gained from observing the driving of about 120 miles of tunnel in California as well as the repairs of some tunnels. SIZE OF TUNNELS It is known that a small tunnel may be more costly to drive than one of somewhat larger dimensions. This fact was found to be true when a tunnel about 4,000 feet long was constructed to eliminate 7 miles of canal. The formation was lava so it was anticipated the ground would be self supporting because of the small bore. Actually the tunnel required support for most of its length and working conditions were poor. It became apparent that a larger size could have been driven at no additional cost and probably in less time. On another unlined tunnel, to be driven in granitic formation, the contractor was given the option of using

Jan 1, 1974

By Kumara S. Rachamalla

Long-term stability, appropriate taxation and incentive policies are essential to attract and stimulate investment in the mineral sector. An outline of Ontario's $4.6 billion industry and associated tax incentives is presented. Producers are offered incentives under The Mining Tax Act, federal and provincial income tax acts for exploration and development by reducing Me after tax cost to 13-25¢ for each dollar spent. The Mining Tax Act provides generous processing incentives which have positive effects in enhancing investment and economic advantages of building processing facilities. Non-mining companies and entrepreneurial individuals can receive 25% of eligible exploration expenditures in grants/tax credits under the Ontario Mineral Exploration Program.

Jan 1, 1982

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By M. S. Bickers

Prior to 1970, the environmental liabilities associated with mine construction and management were few. Mostly, they were aimed at health and safety matters. At that time less than two dozen codes were incorporated into the engineering design and they were somewhat static and well known by the engineering designers and managers. These codes issued by governmental agencies and professional associations are listed in Table 1

Jan 1, 1988

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By J. S. Heath

Many disputes related to environmental issues in mining are resolved through often-antagonistic negotiations in a regulatory context or through litigation. These approaches are certainly the best choices for resolving certain disputes. However, just as no single remediation technology is the right fit for every site, so no single dispute resolution process is the best choice for every situation. This paper introduces a range of dispute resolution alternatives (from collaborative decision making through mediation, arbitration, and litigation). Especially when money is tightest, cost-effective dispute resolution(and the outcomes that can accompany it) can have an impact on the bottom line.

Jan 1, 2000

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By Rodrigo Jerez

This paper describes a Mixed Integer Linear Programming model that was developed for planning the coal operations at Mountain Coals, Inc., in Kentucky. The model incorporates the use of stockpiles as practiced and allows the operator to find the least cost combination of raw coal feeds, washing densities and blending to produce the different quality coals as required by the coal contracts.

Jan 1, 1984

By Jorgensen D. K.

The Bullfrog and Montgomery-Shoshone deposits, outside Beatty, Nevada, have a combined drill-indicated reserve of 17.4 M tons of ore with an average grade of 0.103 oz/t Au and 0.240 oz/t Ag. The deposits occur in Miocene volcanic rocks which underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff which experienced brittle deformation during plate movement. Open-space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micron-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults.

Jan 1, 1989

By W. D. Blackburn

If there is a single key to managing a mineral extraction company, it is the control of productivity. American labor costs, in general, tend to be in the range of 10%-15% of total costs. American coal mining labor costs, however, exhibit ranges of 30%-60% of total costs. Is it any wonder that the industry finds itself at a competitive disadvantage? When labor costs take as much as sixty cents of every dollar of revenue, there is little room for profitability. The American coal mining industry must set as a long range goal the reduction of labor costs to the 10%-15% range of total costs in order to be competitive.

Jan 1, 1986