Search Documents

By Dinah O. Shumway

California's annual production of >11 million tons of cement, at a value of over $640 million, comes from eight companies, which operate 11 plants. Cement is California's second most important mineral commodity, representing 25% of its total annual mineral production. Although most of the cement produced is consumed within the state, current export locales include the Pacific Northwest, Nevada, Arizona, Utah, and New Mexico. An enumeration of the components required to produce cement is deceptively simple: calcium oxide (65%), silica (20%), alumina (4-5%), iron (3-4%), and calcium sulfate (4%) as a retardant admixture. The last, and most expensive, ingredient in cement manufacture is energy. Detrimental materials in cement mixes include excess .magnesium, alkalis, heavy metals, sulfur, and other volatiles. Each of the 11 cement plants in California requires a unique chemical solution of combined raw materials to produce a uniform product: portland cement. The geologist proposing solutions for the additive raw materials in cement manufacture must have a thorough knowledge of a particular cement plant's needs. In the California cement market, keeping the costs of additive raw materials down is one way to also stay competitive, and using a combination of natural and waste materials as additive raw materials allows cement producers to stay competitive.

Jan 1, 1999

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By James M. Riddle

A discussion of frequently asked questions may help individuals trying to interpret subsidence regulations or prepare permit applications. The subsidence permitting process involves just one part of the mass of Surface Mining Control and Reclamation Act regulations. But of the 18 main SMCRA sections, subsidence is critical to the permitting process for coal operators. It's an area in which applicants have had problems interpreting regulations and preparing permit applications. Of 22 western states, only Wyoming, Montana, Colorado, and Utah heave thus far received approval for their mining and reclamation plans. The other states are now involved in the permit application process and will be dealing with SMCRA regulations for the next year or so. Some state programs, when approved, may differ substantially from the federal SMCRA program. But, to be approved, the state programs must be deemed equal to or more stringent than the federal regulations. SMCRA regulations apply to any coal operation "that exhibits surface effects." Thus they apply to surface strip mines as well as underground coal operations. The regulations do not apply to hardrock mining operations. Since August 3, 1977, the government, industry, and the public have wrestled with SMCRA. They have struggled through an initial program with the US Geological Survey; a new agency, the Office of Surface Mining Reclamation and Enforcement (OSM); an interim program; and a "final" permanent regulatory program. Even now, OSM is reluctant to publish formal program guidelines because: •The regulations are still in the process of judicial review. • Some approvable state programs will supersede the federal regula¬tions. • The flexible regulations are open to interpretation, which is desir¬able to maintain. •Guidelines could be misleading until regulations and interpretations are revised and finalized.

Jan 12, 1980

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company's Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979

By Tim O’Neil

Many mining companies try to fight their way up from small operator and exploration company to major producer. Not many companies make it. Cambior Inc., formed in 1986, is one company well on its way to making it as a major operating company. In 1993, Cambior surpassed 15.5 t (500,000 oz) of gold production and began operations at its world class Omai gold mine in Guyana. At the same time, the company has embarked on a program of geographic and minerals diversification. Cambior, a Canadian company, now has interests in eight mines, three development projects and more than 100 exploration properties in North and South America. The company’s goal is to derive 70% of its income from gold and 30% from base metals and other minerals. Cambior’s moderate diversification into base metals gives protection against negative gold price fluctuations. It also balances the typically short term gold mines and the longer term base metal mines.

Jan 1, 1994

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By M. V. Chari

A prime objective of physical coal cleaning is the separation of raw coal into a clean coal product with the required low ash and pyritic sulfur content and a high ash refuse. The refuse should also contain a minimum amount of combustible matter. In order to be effective, cleaning processes require that the mineral matter in the feed, including pyrite, be largely discrete and free particles, liberated so that the particles are not attached or embedded in coal. Liberation of mineral matter from coal, particularly pyrite, was investigated by Bechtel as part of two fine coal cleaning research programs sponsored by the Department Of Energy (DOE), Pittsburgh Energy Technology Center (PETC). Two proof-of-concept (POC) plants, each with a capacity of 900 kg per hour, were installed and tested to evaluate production of ultra-clean coal using microbubble flotation and spherical agglomeration technologies. The plants were designed to produce clean coal with 2 percent ash and pyrite content lower than that achievable by conventional methods. Also, the quality targets were to be attained at energy recoveries above 80 percent. Bench-scale flotation and agglomeration tests indicated that it would be practical to grind the 6 mm top size feed coal to a mean particle size (050) of 10 micrometers in the POC test plant. In this part of the paper, the steps taken in the grinding circuit to maximize liberation of mineral matter are described.

Jan 1, 1991

By R. E. Ray

Compared to conventional fully ducted axial and centrifugal fan systems, jet fans can offer a number of advantages for control of smoke during fire emergencies and dilution of diesel engine exhaust products in vehicular and rail tunnels. The success of jet fan applications is the result of a balance between the temperature de-rating of the fan, buoyancy forces and the installation momentum transfer efficiency. This paper provides a case study of a unique application of vertically-mounted jet fans in ventilation shafts used to provide both emergency ventilation and pollution control for an overbuild created by the construction of a series of commercial high-rise residential buildings over a portion of an existing passenger rail line. A detailed evaluation of a set of shafts for one building is presented, including a discussion of the calculation methods used to estimate the required jet fan capacity and the results of the subsequent numerical analysis using Computational Fluid Dynamics to simulate the performance of the jet fans during train car fire emergencies.

Jan 1, 2009

By G. Sanders

Discussion by G. Sanders The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominantlithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below. Missing the high-grade part of the ore body In your statistical analysis, you directly compare the reverse circulation assays to the diamond drill assays in Section 30. Two points argue against a direct comparison and suggest the differences are greater than the 3 % that you report. First, any core loss in a gold zone most likely means that the true gold values are greater. The drillers lost significant amounts of the clay-rich, Section-30 gold mineralization. Also, the initiated salt-mud system, an attempt to improve the core recovery, met with little success. Second, the practice of not sampling core geologically, but instead sampling on even 5-foot intervals, adds a deliberate dilution to the core assay values by including a portion of nonmineralized rock in the first and last samples of each high- grade intercept. The result is often a pair of low-grade assay values on either side of a high-grade gold zone. In reality, a high-grade gold zone has a very sharp assay wall that is often bounded by barren rock. This sampling method may make the diamond-drill core assays more like the reverse circulation values and may help explain the statistical similarities you found. However, it does not represent the true gold values in the high-grade parts of the deposit. You cannot deny that, by careful geological sampling of the drill core, higher and sharper assay values will be obtained. The low core recovery and the diamond-drill-core sampling method used act together to lower the diamond-core assay values. The 3% difference you found between the reverse-circulation and diamond-core assay values could be much larger when you consider what the true diamond-drill core values would be with optimum core recovery and a geologic sampling method for the core. Should statistics have been applied here? The statement "... that reverse circulation holes have overestimated the values of some ore zones and underestimated the values of others" (p. 345) is not correct. The subsampling confirmed what the cross sections hinted at in Section 30. Namely, beneath the high-grade zones, the reverse circulation holes created, by contamination, large intercepts of low-grade ore in regions of barren rock. Because the low-grade material was not there to begin with, this is not a process of overestimating low-grade mineralization. The next statement that "the average result is similar to that of the diamond drill holes" may apply to the data set numerically, but it is not true when viewed spatially on cross sections. Adjacent reverse circulation and diamond drill holes are almost impossible to correlate, high-grade zone values vary widely and many low-grade intercepts make no geologic sense. The subset sampling and cross sections presented in the first part of the paper show that the reverse circulation portion of the data set has some serious problems, as highlighted above, and should not have been dealt with statistically at all. Conclusion Each ore body is different, and each drilling method presents unique sampling problems. In this case, the diamond drill is the

Jan 1, 1994

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By P. Petropoulakis

Computer technology in the mining activities of our company has been applied in the last decade. In this presentation the experience gained by applying this computer technology in mining spescific applications are reported. Attention is given to the problems phased out and to the methodology used for software selection, centralized and decentralized development, data processing personnel and end users training and support. The paper concludes with a report of the first results obtained and a look at the future developments of the system.

Jan 1, 1989

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (K. McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project will be completed in early 1998.

Jan 1, 1998