Search Documents

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By H. Suharyono

A laboratory investigation of flocculation following polymer addition during slurry flow through pipes and in-line (static) mixers is described. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points on flocculation performance as measured by settling rate and supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests, both batch and continuous, conducted in stirred tanks.

Jan 1, 1995

By Ken Goering

"Bridgestone Americas opened the company’s first U.S.-based giant off-road radial (ORR) tire plant in November. The 139,000-m2 (1.5 -million-sq ft) plant, located on a 222-ha (550- acre) site in Aiken County, SC, will produce radial tire products, including 157-cm (63-in.) tires, used on mining and aggregate haul trucks.The plant, announced in 2011 as a $970-million investment, represents the largest investment that Bridgestone has made in the United States, and is also the single largest investment ever made in South Carolina. Although it had already been producing tires for a few months, the plant officially opened with a ceremony in November 2014, attended by South Carolina federal, state and local elected officials, as well as Bridgestone personnel from the United States and Japan. Prior to the Aiken County plant’s construction, all of Bridgestone’s giant ORR tires were manufactured at its Shimonoseki and Kitakyushu facilities in Japan.Kurt Danielson, president of Bridgestone’s U.S. & Canada Commercial Group, said the facility was built to primarily serve the North American mining and aggregate industries in a more efficient manner. "It’s a real change for us," he said of the U.S.-based plant at its opening ceremony. "This allows us to have a true global presence."The Aiken County plant is intended to allow Bridgestone to meet customer demand for ORR tires, Danielson said. "It really frees up our other plants in Japan to service the rest of the world, allowing us to serve our customers faster," Danielson said. "As soon as we build (a tire), we can have it to our customers."Tires manufactured at Bridgestone’s Japanese plants could spend up to a month in transit to the American continents; from initial mixing of the rubber and other compounds to being warehoused, tires manufactured at the Aiken County plant can be ready to ship in four to five days.Danielson said most of the tires built in Aiken County will be used by customers on the American continents. "We will export," he said, "but our desire is to use as much capacity as we can for the Americas."Ground was broken for the facility inSeptember 2011, when commodity prices were much different than today and global demand for tires had skyrocketed."

Jan 1, 2014

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By T. D. Kaufmann

When Dr. David Gully solicited this paper last spring a few questions basic to commodity trade between the U.S. and world markets appeared perplexing. Why, for example, when the demand for aluminum was at a peak and when little expansion of capacity had taken place, was the dollar price half of what it had been at the previous peak? Or, why in 1984 when imports surged by 50% as the U.S. economy pulled out of its recession did the dollar not fall, but rather rose by 35%? And, why when the experts all seemed to agree that the dollar was grossly overvalued did the price of gold continue to decline? Surely these were extraordinary times for the mineral economist. When this paper was written in late July, 1985 the answers seemed clearer. The prices of many commodities were not low - the dollar in which they were denominated was too high. In other currencies many commodity prices were indeed high. The dollar was overvalued in trade terms by some 40% caused by an influx of short term coupon investments made by foreign money managers to take advantage of the higher short term interest rates in the U.S. relative to other international banking centers. With a decline in the relative difference in interest rates, an unhealthy buildup of foreign bank accounts and a perception that the dollar would fall, the dollar did start to decline rapidly.

Jan 1, 1985

By G. C. Knutsen

The Post deposit is located in Eureka County, Nevada, about 37 km (23 miles) northwest of the town of Carlin. Post occurs on the Carlin Trend, a northwest alignment of 14 major gold deposits, each containing more than three tonnes (t) (100 000 ounces) of gold. Deposits of the Carlin Trend are epithermal, sediment-hosted, disseminated gold occurrences, collectively containing more than 622 t (20 million ounces) of gold. Three major gold producers active on the Carlin Trend are Newmont Gold Company (NGC) (12.4 t/400 000 ounces of gold per year), Western States Minerals Corporation (WSMC) and Pancana Minerals joint venture (1.56 t/50 000 ounces of gold per year), and Dee Gold Mining Company (1.4 t/45 000 ounces of gold per year). The Carlin Trend has also been referred to as the Lynn-Railroad Mineral Belt. This district is characterized by open-pit mineable, micron-sized gold, hosted in Paleozoic sedimentary rocks. Six geological subdistricts comprise the Carlin Trend, each characterized by differences in host lithology, structural controls, alteration assemblage, or style of mineralization. The six geologic subdistricts include, from south to north, Bullion (Railroad), Rain, Maggie Creek, Lynn, Bluestar-Goldstrike, and Bootstrap. With the exception of the Bullion subdistrict, which was primarily a producer of base metals, each sub-district contained mineable reserves in excess of 31 t (one million ounces) of gold.

Jan 1, 1987

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have ben made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modelling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developped, which can be calibrated far ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables to predict the complete composite particle distribution, and is thus valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1985

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By D. D. Carda, S. Dunn, W. E. Dunn, T. Storbeck

Gold chlorination which will be presented in this paper is limited entirely to the use of gaseous chlorine in a fluidized bed reactor at elevated temperatures in the absence of aqueous water. The only water used in this process is that which is used in scrubbing the effluents. Low temperatures are defined as those below 500°C. All experimentation for this paper was carried out on a laboratory scale, with all calculations extrapolated frpm this. Some of the data is drawn from work with other projects which have been operated at pilot and larger scale.

Jan 1, 1998

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By J. Libaude

The Changement mine in French Guyana has, since 1983, processed gold ore by classical gravity methods. A large part of the gold is in the form of very small, free or enclosed grains. Recovery by gravity methods is thus limited (25-30%) and the present plant produces about 40,000 t annually of auriferous waste assaying about 6 git. The company therefore decided to retreat the waste by heap cyanidation. After laboratory tests which showed the feasibility of the method, a pilot test was set up on site. An experimental 3000 t heap, composed of waste of 0-8 mm grain size, was laid out by bucket loader on an impermeable pad covered by PVC and geotextile cloth. The upper layer of the heap was reworked by mechanical shovel to break up the area that had been compacted by the passage of the loader so as to restore adequate permeability.

Jan 1, 1998

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By T. W. Mattioli

Restrictions on fugitive emissions and crushing operations continue to get tighter. Although fugitive dust control in the gold mining industry has historically been difficult, there are now several options that can make dust control both effective and efficient. Using new technology, mine operators can now design and maintain a dust control program that can reduce product losses, decrease equipment failure, cut cleaning costs, and meet air quality compliance standards as well as provide a better working environment. This paper discusses the sources of fugitive emissions related to the gold mining and crushing operations and describes effective new control methods.

Jan 1, 1998

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By O. A. Lima

Effective solids suspension is a necessary precondition for particle collection, and solids suspension is largely dependent on the hydrodynamics of the flotation cell. This study attempted to correlate the status of the suspension of apatite particles of different sizes in a Denver laboratory flotation cell versus the impeller rotational speed (N) adopted to operate the machine. The latter variable (N) influences the impeller capacity to lift the particles from the bottom of the tank and also to disperse them throughout the volume of the vessel. Such an impeller capacity can be characterized by the critical impeller speed for the accomplishment of solids off-bottom suspension (Nz) and also by the velocity of the radial water flow discharged by the impeller (U) divided by the particle terminal settling velocity (Us). This way, the status of the suspension of apatite particles inside the flotation cell can be characterized by one of three categories: ?segregation? (N/N2 < 0.60 and Us/U > 0.08); ?suspension? (0.60 = N/N2 < 1 and 0.06 < Us/U < 0.10); and ?dragging? (N/N2 = 1 and Us/U = 0.03). The range of impeller rotational speed (N), which was able to suspend the finest particles (Dp = 90 µm), was unable to suspend the coarsest particles (Dp = 254 µm). Conversely, the high value of N (N > 1,300 rpm), which is adequate to suspend the coarsest particles, may promote the entrainment of the finest particles to the froth layer.

Jan 1, 2009

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025