Search Documents

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By L. A. Morley

Electricity is a major cause of lost-time accidents and fatalities in the mining industry. Major hazards and unsafe practices that contribute to electrical hazards are identified in this paper. Recommendations for reducing electrical accidents in surface mining are given and are directed toward the following three areas: preventing equipment contact with overhead lines, preventing maintenance related accidents, and defining system protection techniques.

Jan 1, 1986

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By Jacob Feld

Introduction The best way to eliminate the possibility of rapid excavation in tunnel work is to start an argument between Owner Engineer and Contractor. And arguments are readily started when work is progressed without a frank open agreement on the rules of the game. Fifty years ago a tunnel contractor took a job to excavate and line a tunnel, providing all labor and materials under the guidance and continuous instruction of the Engineer who provided all survey work, checked each new heading and set the lines for the next round of drill holes, usually designed and ordered protective measures, kept record of progress and controlled payment for the work. In my first job in a tunnel, muck cars were loaded by hand and hauled by donkeys. Progress was, at today's criteria, not rapid. The Contractor or in the case of a large concern, his executive field representative was always at the site, knew most of his men by name, and there was a mutual feeling of respect between him and the Engineer in charge of the work. Misunderstandings were cleared up when they came up, expeditiously and fairly, even though satisfaction was not always expressed. The Owner came for the ground breaking and usually for the holing through shot. The Owner had full reliance on the Engineer's ability and integrity. The Engineer recognized the Contractor's expertise in being able to man the job and produce results.

Jan 1, 1974

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Johann Knecht

Due to lower specific investment and operating costs the tendency towards large scale equipment will remain. For the design engineers not only the stresses in the mill structure and manufacturing are of importance but also transportation to and erection on site. A scale up of the design of smaller sized units on the pantograph principle may not always give the best approach to the job in this respect. This paper covers recent developments in the design of large size equipment where the huge dimensions call for designs being different to the well known ball and SAG mill concept with cast conical endwalls. The first part describes the features of the biggest ball mill in the world, whereas the second part provides some details of the largest shell supported SAG mills being currently in the manufacturing process.

Jan 1, 1993

By Rambabu Pothina, MELO EDUARDO PIMENTA DE, Rajive Ganguli

 The mining industry is home to a mass of sensor-generated data that are critical to real-time and long-term optimization. This heavy reliance on sensor data has resulted in an undesirable development. The industry is reluctant to verify the accuracy of sensors as it would mean shutting down important processes. Sensors are typically calibrated once a year, if at all. Errors in sensors go undetected until the next calibration or until errors are so gross as to be obvious

By Stanley M. Moos

In reviewing available vacuum filtration equipment in this paper, several types of filters have been included which are probably not familiar to operators in the mining industry. However, it was felt that these units might be of interest in the event that an application should arise for the filtration of a product in the future that does not exist today. In addition, exposure of our industry to equipment used in other industries might have a tendency to be thought provoking and perhaps lead to the development of equipment and/or applications in our industry which do not necessarily exist at this time. Most innovations in filtration equipment have been confined to the improvement or design change of components and accessories, particularly reflecting the availability of materials of construction that have been developed. Recent developments in the application of horizontal belt filters have been innovative. The application of this unit as a substitute for or an adjunct to thickeners in a CO circuit can certainly be innovative and perhaps provide a basis for reduction in capital and operating costs in this area. For example, mill tails are generally pumped at the highest possible density that will adequately flow. Tailings ponds and dams with their attendant design requirements are based upon this estimated water volume. Availability of a much dryer, non-flowing filter cake opens up several new options for disposal. Considerable cost savings could result in the design and planning of disposal areas for containing dryer material. . No attempt has been made in this paper to provide a manual for the operation of all of the many types of equipment that are available. Rather, the paper tries to present an overview.

Jan 1, 1978

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By Eileen Ashworth

Introduction A study was completed that investigated the enrollment in mining engineering programs in 24 universities and colleges. All programs considered in the study award four-year bachelor of science degrees in mining engineering. They also provide all the engineers for the mining industry and a large portion of the geotechnical engineers working on environmental problems, storage of hazardous waste, civic, and Federal government underground projects. The numbers used as the base for the study are those reported by each program to SME-AIME and published yearly (SME, 1986). Data for the study came from the period 1975-1985. Also, since some programs include students in related disciplines and special categories, such as cooperative students, a few inaccuracies were unavoidable. A 23-page document has been prepared that reports on the overall picture of current enrollment, the trends, and discusses the results, perceived effects, and what can, or should, be done. There has been an obvious, and dramatic decrease in total undergraduate enrollment since the late 1970s. In 1978, 3117 students were enrolled. In the 1985 fall semester, enrollment was 1022, less than one-third. There were 485 seniors, 265 juniors, 147 sophomores, and 125 freshmen. The downward trend in total enrollment is likely to continue for at least another two years. Class size The catastrophic drop in enrollment is shared by all programs across the country. It does not discriminate between types of programs, coal or hard rock mining, or location. In general, 1985's enrollment is about 30% of whatever the maximum enrollment was in any program, though this varies from the teens to 50%. The latter percentage occurs only for some programs with special circumstances, particularly new programs not well established in the late 1970s. The beginning of the decline in enrollment has occurred at slightly different times as affected by the demise of each program's local industry. The numbers in each class produced from a specific freshmen year (Fig. 1) are worthy of comment. The dramatic drop in enrollment for all classes after 1982 is clearly demonstrated. The timing coincides with the general downturn in the mining industry, when many employed engineers were laid off and new graduates could not find jobs. Also, significantly fewer students are being attracted to mining programs as freshmen. The number of seniors shown seems inappropriate. Where did so many seniors come from and why are so few graduates produced? There is an increasing trend for students to take four-and-a-half or five years to graduate. Therefore, they are counted twice, once when they are first classed as seniors and again the following year. Some students purposely delay graduation to obtain more summer work experience and take additional courses. They believe that this gives them a better

Jan 8, 1986

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

Atlas Copco Wagner launched its ST1010 Scooptram load haul dumper. The ST1010 replaces the company’s Wagner ST-1000 Scooptram. The improvements to the Wagner ST1010 include increased reliability, ease of maintenance and driver comfort or ergonomics. The ST1010 has been redesigned and has added several new features and options not offered in the earlier model. These include anew boom design with side stops. Heavy reinforcements to the bogie offer better protection against the harsh working conditions in underground mining and tunneling. An auto lube system has also been added as has paint-on grip tread to reduce slips and falls during maintenance checks or repair work. Other features include a heavy-duty, auxiliary-fan motor, an isolated transverter, remote diagnostic pressure taps, a bolt-on battery box, raised air-intake, improved fuel-filter access for easier maintenance, larger wear-bars around the engine tub, and smaller, higher output batteries

Jan 1, 2000