Search Documents

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By John Wiebmer

Several industry trends are putting new demands on surface mining equipment. This is true both on the “hard” side of the equipment business - the research and product development programs, and on the “soft” side - the business processes, human resources and competitive strategies. This article describes seven key industry trends and the impact each is having on surface mining equipment suppliers. 1. Globalization Earth-spanning technologies are shrinking the world into an economic village, causing corporations to think and plan on a global scale. This “globalization” is one of the great buzzwords of the 1990s, meaning precisely whatever the user says it means. In this case, let us take it to mean that political boundaries arc less restrictive than in the past, permitting mining companies new freedom to roam the globe for ore bodies. Evolving out of this are global mining houses that have ownership and management interests in labyrinthian webs of mines spanning the world. There are several impacts on surface mining equipment suppliers.

Jan 1, 1994

By Siegmund Babendererde

1. Introduction In Sayreville, New Jersey, the Middlesex County Utilities Authority put the construction of a 1041 m long sewer outlet to tender in June 1989. It had an internal diameter of 3,36 m and was part of a sewage treatment works project for county Middlesex. The contract was awarded to the Lodigiani Company, USA, who employed Hochtief Incorporated as subcontractor to drive the sewer outfall. 2. Ground Conditions According to the preliminary geological site investigation, carried out by the consultants Metcalf & Eddy, the tunnel passed through marine deposits.

Jan 1, 1991

By Scott G. Britton

In the real world of coal mining, the bottom line for almost every support project decision is economic (i.e., what is it going to cost?). Up to this point, I have discussed the methods to improve the performance of typical support projects by better installation, materials, and techniques, thus lowering the impact of the bottom line cost. In this chapter, 1 shall explore what costs are relevant in mining construction, and how these costs are developed. The chapter centers around two major discussions: (I) developing cost accounting techniques, and (2) cost-estimating procedures for support construction. Each focuses on the fundamentals of practical cost considerations necessary for decisions on construction projects underground. Since cost accounting, economics, and investment planning are all subjects which warrant complete discussions on their own, this chapter will focus on distilling the important concepts required by a planning engineer into an easily understandable presentation.

Jan 1, 1983

By Schebek, J. Warsen

"Data and information from sustainable development (SD) reports can be seen as a promising and easily accessible source for an Life Cycle Assessment (LCA), i.e. for generic Life Cycle Inventory (LCI) data in particular. The reliability and comparability of LCA results crucially depends on the quality of LCI data, that is defined by specific normative requirements. In parallel the GRI (Global Reporting Initiative) provides a set of guidance documents for enhancing the quality, rigor, and utility of SD reporting with specific reporting principles that address similar issues on a company level comparable to LCI data quality requirements on the process level. In order to assess the general suitability of the fundamental reporting principles for LCI data quality purposes selected reports from mining and minerals (M&M) sector are assessed within a detailed analysis."

Jan 1, 2005

By Patricia O. Milley

Two years ago, AlliedSignal embarked on a journey to improve QUALITY. However, the focus of this endeavor was on the CUSTOMER and not the traditional product focus. It wasn't that a focus to improve product quality wasn't fruitful in the past. We've practiced it in the chemical industry for many years with significant results. But our industry today is in a survival mode and yesterday's way of doing business is simply not good enough. In the mining industry, we have to make lug strides in how we do business or face losing our customer base. As you are well aware, other parts of the world are importing our technology at a rapid rate. We must work smarter to stay ahead of our customers ever more demanding need for higher quality at lower prices. With this as a driver, throughout the Corporation we reviewed in depth how we support our customers to keep them competitive and sought to eliminate work which did not help them reach this goal. Our first year of emphasis was on tools: how to hold meetings, gather data, and how to make decisions. This sounds very basic, I know, but you can't begin to imagine how productive meetings can become when you start with an agenda and prework delivered days in advance, and agree at the start of the meeting what should get accomplished. In the second year, we applied these tools to our work processes. We mapped how we do our work, scrutinized each step for value to the customer, and then set to work on how we could do things better. The areas we concentrated on were customer linked commercialization of new products, manufacturing and materials management. Our discussion today will focus on the commercialization of new products.

Jan 1, 1994

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By L. W. Teal

The Paupers Dream Property is located in the northern Boulder Mountains, southwestern Montana, 30 km southwest of Helena. The property is situated in the central portion of the Butte-Helena gold belt, a NE trending lineament marking a zone of recurrent, late-Cretaceous to mid-Tertiary volcanic activity. Geology consists of a plutonic basement of late-Cretaceous quartz monzonite overlain by a pre-volcanic basal conglomerate and a complex sequence of Oligocene rhyolitic volcanics. Gold mineralization occurs in fracture-controlled quartz veins, silicified stockwork, and brecciated shear zones as auriferous pyrite, arsenopyrite, and disseminated free gold. An estimated 60,000 tonnes averaging 2.5 g/t was produced from the Porphyry Dike, Venus, and Paupers Dream Mines on the property. Current drill indicated reserves (May, 19861 are placed at 6,946,000 tonnes averaging 1.45 g/t gold.

Jan 1, 1987

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023