Search Documents

By R. Ramesh

Understanding the nature of coal surface heterogeneity is a prerequisite to accurate characterization and efficient control of coal surfaces. New techniques based on the centrifugal immersion of particles from the liquid/ vapor interface and film flotation have led to independent estimation of surface energy distributions in individual coal particles. Changes in the distribution of surface sites due to oxidation and polyacrylamide adsorption on coal are studied here using the above techniques. New information on -possible conformations of adsorbed polymers is also obtained.

Jan 1, 1989

By L. F. Delgado

Environmental and cost pressures sparked renewed interest in gravity separation. Industrial sands in Mexico are generally processed by screening, desliming, and flotation. Gravity separation with spirals was evaluated as an alternative to flotation in order to lower operating costs and decrease water pollution. Outstanding operating results are obtained in glass and foundry sand operations, plus a more competitive position for Mexican producers due to lower operating costs. Coal fines, generally recovered by flotation, have the same cost and environmental advantages when processed with spirals.

Jan 1, 1994

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By A. G. Kim

Increasing transportation costs, clean air regulations and the decreasing availability of landfill space are factors in the increased interest in the utilization of low cost disposal sites for coal combustion residues (CCR). Inactive surface and underground coal mines can satisfy the conditions for stable CCR disposal sites, and subsurface CCR injection can be beneficial in reducing the amount of acid mine drainage (AMD) often produced at such sites. The material is expected to add alkalinity to the subsurface environment and to decrease the permeability and porosity of the buried spoil. Both mechanisms can reduce the amount of acid normally generated at a mine site. The Bureau of Mines is cooperating with an independent coal company in a test of subsurface injection of a mixture of fly ash, from conventional power plants or from fluidized bed combustion (FBC) , with AMD sludge into a reclaimed surface mine. Changes in water quality parameters and the concentration of heavy metals in water samples from wells and seeps are being used to assess the effect of CCR injection. The preliminary results discussed here indicate that improvement in subsurface water quality was related to fly ash injection and that components of the fly ash were stable in the acid environment.

Jan 1, 1994

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By Stephen R. Hunt

This paper summarizes some preliminary results of the Illinois State Geological Surveys current investigation into surface subsidence resulting from coal mining in Illinois. The purpose of the study is to characterize-the vertical movements that may result from various types of underground coal mining. In general there is relatively little published information about subsidence from room-and-pillar mining as compared with longwall mining. The findings of this study, based on mining operations in a variety of geologic settings, delineate the magnitude, shape, and position of the subsidence profile. Comparisons of case histories of subsidence are based primarily on the extraction ratio and the general geometry of the mine (depth, panel width, and mining height).

Jan 1, 1979

By O. D. Christensen

The Carlin Trend is a 60 km (38 mi) long northwest alignment of epithermal, sediment-hosted, disseminated gold deposits. Collectively, these orebodies contained more than 620 t (20 million troy ounces) of gold. The Carlin deposit, located near the center of the Trend, has become the "type" deposit of this class. There are, however, significant differences between the individual deposits. Six subdistricts can be distinguished, based upon geographic, structural, lithologic, alteration, mineralization style, and geochemical characteristics. They are, from northwest to southeast, the Bootstrap, Bluestar-Goldstrike, Lynn, Maggie Creek, Rain and Bullion (Railroad) subdistricts. Regional Geologic Setting The Carlin District is located centrally within the Great Basin Geologic Province. Host rocks for the deposits include sedimentary units that range in age from Ordovician to Mississippian, as well as a Jurassic-Cretaceous granodiorite stock. During the Early Paleozoic, the area that is now Nevada lay along the western margin of the North American continent. A westward-thickening wedge of sedimentary units was deposited offshore in a eugeoclinal basin; these vary from continental shelf carbonates toward the east to fine-grained siliceous clastic and cherty units to the west. Tectonic activity associated with the Antler Orogeny in Late Devonian to Early Mississippian time resulted in the eugeoclinal Western Assemblage rocks being thrust as much as 140 km (90 mi) eastward over time-equivalent transitional to miogeoclinal Eastern Assemblage rocks along the Roberts Mountains Thrust fault system. The leading edge of the Roberts Mountains Thrust plate formed the emergent Antler highland from which siliceous clastic sediment, eroded from the overriding eugeoclinal rocks, was shed eastward into the adjacent foreland basin. Erosional products derived from the overthrust plate are termed the Overlap Assemblage.

Jan 1, 1987

By R. L. Nielsen

The thematic mapper (TM) aboard Landsat II records image data at seven wavelength intervals or bands. Three record the visible region; three record reflected IR energy. A false color image combining bands 7, 4 and 2 rendered as red, green and blue respectively provides maximum discrimination of rock types in arid regions. Structural analyses and interpretation defines regional structures, large volcano-tectonic features intrusive complexes, all which localize mineralization. Special digital processing using the ratio: Band 3 / Band 1 can identify limonites and other iron minerals. The ratio: Band 5/ Band 7 identifies clays and alunite. These ratio images show features and patterns of hydrothermal mineral systems: ?patterns of sulfide and alteration zoning in large porphyry systems, and zones of strong silica, quartz-alunite-illite, and pyrite-sericite in epithermal centers. Thus, digitally processed Landsat TM images are a cost effective and rapid means to recognize altered areas and define targets for large mineralized systems.

Jan 1, 1995

By Bill Reid

Coal companies mining the seams in the Appalachian region appear to be optimistic. Although some older mines are closing, newer mines are expanding. Money is being spent on new equipment and research to increase mining productivity, as well as improve safety. Coal has been produced from the rich Appalachian seams for about 200 years with no end in sight. Many equipment manufacturers have substantial backlogs of orders for new equipment. Some of the innovations being monitored by the Appalachian underground coal operators include au¬tomated longwall mining, continuous haulage systems and methane drainage. Appalachian coal was a major ingredient in the steel that culminated in the Golden Spike ceremony at Promontary Point, UT, where the final link in the transcontinental railroad was closed. This occurred on May 10, 1869, according to a history published by Union Pacific Coal Co. It stated that "rails and fastenings for track construction were purchased in Danville, Scranton, and Johnstown, PA and Troy, NY." Ever since, coal from the eight Appalachian states has contributed in no small measure to geographic expansion and economic growth of the United States.

Jan 1, 1995

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By John Wiebmer

Six industry trends will have significant effect on the way mining equipment is designed and supported in the years ahead: 1. MINING IS MIGRATING TO LESSER DEVELOPED PARTS OF THE WORLD The global recession of the early 1980's drove down commodity prices and intensified cost competition. This caused a fairly dramatic trend in mining away from higher cost operations in developed countries to richer, lower cost deposits in developing countries. Miners operating in lesser developed parts of the world will place higher value on rugged, durable designs that can live in more difficult and sometimes abusive conditions. They need engines and power train systems that are more tolerant of a wide variation in fuel quality and oil specifications. They'll require machines that are simpler to operate, simpler to maintain, simpler to troubleshoot and simpler to repair. And they'll require creative means of support in getting technical information, parts and components to remote operational sites. Mining equipment in the future will be more durable and simple than it is today, and product support will grow in importance as purchasing criterion. 2. THE MINING INDUSTRY IS CONSOLIDATING An intense amount of corporate acquisition and industry consolidation activity is occurring, to the point that today just 50 mining companies account for 55% of the western world non-fuel mineral production. Consolidation will continue, leading in the future to an industry structure weighted heavily toward a few key global mining houses.

Jan 1, 1993

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By R. C. Freas

Imported products and materials have been in the news over the last several years in a wide variety of industries. Certainly the mining and industrial minerals industry has not been exempt from this. Cement imports have received considerable attention in the press and a number of written articles. We are also seeing imported aggregates particularly along the gulf coast and east coast of the United states. We are now hearing increasing talk of bringing high brightness calcium carbonate from offshore sources into the U.s. domestic markets. This paper takes a look at the location of these sources, factors affecting their acceptance by U.S. industry and presents a general cost comparison of offshore and domestic calcium carbonate. In addition, the market response of U.S. suppliers and the impact of imports is also discussed.

Jan 1, 1989

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974