Search Documents

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

Operation of a pilot-scale Floatex density separator was studied using a pyrite concentrate slurry feed. Experimental measurements were further utilized in parameterization of a hindered settling simulation model. The model incorporates particle slip velocity calculation and also a separation efficiency function, adjusted to describe the feed material characteristics. The model was used to compute the overflow and underflow compositions when both fluidization bed pressure and teeter water flow rates were varied. In addition, prediction accuracy and the model validity were evaluated. The simulations gave good results when the teeter interstitial velocities were moderate enough to avoid excessive turbulence in the fluidization. Prediction of the cumulative overflow and underflow size distributions in most experiments yielded essentially less than 10% relative error between the sample data and the estimated value of the 50% passing sizes.

Jan 1, 2011

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles) northeast of Winnemucca, Nevada. The deposit is owned by First Miss Gold Inc. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 m (1 400 ft.) to 671 m (2 200 ft.), along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate within the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By D. S. Bloswick

An investigation an4 analysis of slip/fall accidents specifically pertaining to underground coal mines was conducted. From a population of 751 accident reports, three major sources of injury which account for over 80% of the incidents have been identified. The specifics of this study are presented in this paper. Based on the results, several recommendations are made to reduce such accidents in underground mines. In addition, a brief discussion of the slip-hazard analysis laboratory at the University of Utah, which will be useful in future analyses of these accidents is presented. Work in this facility includes the simulation of certain mining activities in a controlled setting. Foot forces are measured and work methods subsequently developed to minimize the slip potential of these activities.

Jan 1, 1988

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By G. Baldermann, Hüttenrauch

Occupational health and safety are an important tool to increase a company’s economic efficiency. The integration of safety-related tasks into the overall structure of entrepreneurial tasks is an inalienable requirement for the sustainable achievement of positive effects. Investments into technical and personnel occupational safety that are tied in a streamlined organizational structure guarantee the improvement of defined indicators. The labor force is of central importance. Its added value ought to be ensured. It is necessary to move away from the employees‘ hazard awareness towards a safety awareness including many other aspects in order to save costs in the long run.

Jan 1, 2005

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By A. S. Kastrinos

There are many concepts of preventative maintenance. The basic objective of all maintenance organization, however, is the efficient (accomplishment and control of all) inspection, repair, overhaul, material and preventative maintenance functions necessary to maintain facilities and equipment in a condition that will meet operating requirements at a level consistent with low costs and high availability. To formulate a preventative maintenance program requires sound judgment and the ability to apply in a practical manner a system that meets Plant operation requirements, based upon organization, experience, conditions, design and historical data. A maintenance program must be divided into to categories consisting of: 1. Scheduled tasks to be accomplished at planned intervals. The objective of these tasks is to maintain reliability and prevent as much as possible abnormal failures. 2. Non-scheduled tasks that result from periodic reports and which can be scheduled to fit in conveniently with other routine work. The non-scheduled work items may include long-range preparation for lenghty shutdowns requiring Engineering and Shop services.

Jan 1, 1975

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992