Search Documents

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

To reduce the environmental footprint of hydrometallurgical processing of black mass from spent lithium-ion batteries (LIBs), a green leaching system based on glycine and sodium metabisulfite (Gly-SMS) was proposed. The leaching study demonstrated that the highest cobalt and lithium recoveries of 100 percent and 99.8 percent were achieved under optimal conditions. The leaching mechanism revealed that the dissolution of LiCoO2 in the Gly-SMS solution followed the shrinking core model. The apparent activation energies for cobalt and lithium were determined as 48.05 and 41.51 kJ/mol, respectively, indicating a surface chemical reaction controlling mechanism. The leachate was then processed by an acidification- precipitation technique with oxalic acid as the precipitant to remove cobalt. Glycine complexes with metal ions by zwitterionic ligand and recycles in the leaching-precipitation circuit, reducing the reagent cost. Compared to other studies, this leaching system has near-neutral operating conditions and is cost-effective, making it an economically viable alternative for treating cathode materials from spent LIBs.

Dec 1, 2024

By William D. Leech, Peter S. Buskirk

Virginia Electric and Power Company commencing in early 1985 will begin operating the Bath County Pumped Storage hydroelectric facility, presently the largest capacity installation of its kind. Six concrete lined vertical shafts, 3 ea x 44.0 ft (13.4m) diam x 330 ft (100m) and 3 ea x 28.5 ft (8.7m) diam x 740 ft (226m), comprise a portion of the three underground power conduits. The project team decided to employ the slipform over the conventional jump form method. This selection was based on the engineer's hydraulic design and the contractor's performance requirements. This paper presents the key elements of the shafts' successful slipform operations. The contractor achieved slip rates as high as 60 ft (18m) per day; and the owner received competent permanent linings as specified by the engineer. The authors describe the team's effort to progressively improve both concrete quality and placement rate.

Jan 1, 1985

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By Roland B. Drugge

The adaptation of pelletizing processes involves the coordination of various factors such as temperatures, gas flows, productions, etc., in order to obtain optimum performance. The consequent problems are considerable due to the large number involved as well as the lack of knowledge of their correlation. It is therefore essential to establish a fundamental theory which takes into account the heat transfer phenomena and the secondary factors which are relevant to the properties of the product. Straight grate and grate kiln pelletizing processes involve heating of a stationary bed on a travelling grate. The heat transfer conditions are therefore of primary importance. This is why this article pays particular attention to conditions which obtain when a stationary bed is heated, in which certain special reactions occur. The conclusions drawn from this penetration of the heat transfer phenomena can be expressed in postulates acting as guide-lines for the establishment of proto-typal processes. Examples of elaborating such processes are also given in the article. Some operational experience at LKAB are also given.

Jan 1, 1975

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Hans von Michaelis

Very little has been published about Cia de Minas Buena­ventura. Don Alberto Benavides Quintana, now in his seventies, founded the company in 1953. This venerable gentleman is a Doyon of the Peruvian mining industry and more has been known about him than about his company. Buenaventura is a highly profitable gold producer with excellent potential to expand gold production in joint ventures with Newmont, Southern Peru Copper (ASARCO), and BRGM as well by developing their own new gold mines. On September 15, The Wall Street Journal published an article titled "Peru's Big Rebound Sets Off Foreign Investors' Enthusiasm."

Jan 1, 1995

By V. Avdiyskiy

The most pressing topic raised nowadays by the world community faces environment and social consequences of the business intensification process, primarily that of mining and mineral industry, which is through the number of its activities mostly associated with pernicious impacts. World top managers are confronted with the dilemma of reconciling traditional financial framework aiming at successful business development measured by revenues, shareholder value, profit margin and incorporating Sustainable Development (SD) at all levels of decision making process, avoiding depriving future generations of the means to meet their own needs. The rapid consolidation and globalization of the industry stipulates that companies are an integral part of the world economic environment. Therefore a company?s financial performance is under the pressure of operational and environmental performance. Among them special attention is paid to the social and economic background, the relationship with regulatory institutions, and the developments for environmental protection.

Jan 1, 2003

By François Martin, Roland Plassart, François Laigle

"MOTIVATION The storage of nuclear waste gives rise to a lot of innovative issues for underground space technologies. The nuclear activity of waste generates temperature effects on both the lining and the surrounding rock mass. In order to avoid these unfavorable effects, the number of waste containers is controlled in the gallery section. The galleries section has consequently ranged from a diameter of 4 to 6 meters. However, in the case of intermediate-level nuclear waste, due to the lower temperature, the number of containers in a cross section of a gallery is assumed to be safely increased. Despite technical difficulties, a large diameter gallery (typically 12m excavated) seems to be more cost effective. This paper demonstrate the feasibility of such a gallery in the specific context of CIGEO (French Geological Repository Project for nuclear waste), located in the Bure area in the north-eastern of France. The geology of Bure at the project’s depth (about 520 meters) consists in a quite homogeneous layer of Callovo-Oxfordian argillites (COx argillites). With such an overburden, this rock is known to have a high plastic behavior with significant time-dependent effects. These mechanical properties require complex behavior laws in computational modeling used for the design of underground facilities.EXPERIENCE OF LARGE DIAMETER GALLERIES In order to identify some specificities in the design of such openings, a research has been run on existing galleries of large diameter (more than 10 meters), like the tunnel of Chamoise, Lötschberg, Tartaiguille or Saint-Martin-La-Porte. Two of these representative examples are detailed hereafter. Tunnel of Chamoise (French Jura) In spite of a lighter overburden (400m versus 520m), an anisotropic initial stress state and a variable rate of carbonates, the highway tunnel of Chamoise is quite similar to the planned gallery for intermediate-level nuclear waste, with a geology very close to the CIGEO’s one in some sections. Because the northern tube encountered difficulties during the excavation a few years before (several over-excavations and spalling, especially in the bench), the excavation of the southern tube has been carried out in two steps, but with a high bench and a small curved invert (Figure 1). The design of the immediate support consists in long bolts and a shotcrete layer. The concrete lining is about 50cm thick."

Jan 1, 2016

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By D. Gove

Several coal mines in Southeastern United State face the problem of multiple, very thin coal seams or seams adhering to interburden, and because of the strip ratio economics, these seams must be recovered. Over the past few years several mines have discovered a common method to solving these problems...use of a Caterpillar RR-250 Road Reclaimer.

Jan 1, 1995

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974