Search Documents

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By Frank W. Reinrniller

Mill ball charging systems have undergone little change during the past two decades. Most operations utilize a locomotive/ball car combination to load and haul charges from the ball storage bin to the mill charging boxes or, alternatively, transport charges to the charging boxes by means of a ball bucket handled by bridge crane. This paper describes a new concept in ball handling systems that is in operation at the Island Copper Concentrator of Utah Mines, Ltd. at Port Hardy, B.C. This system employs a narrow belt conveyor to convey a weighed charge to each of nine belt unloading stations at the mills. In operation, the system has proved to be practicable, trouble-free and economical of operating labor.

Jan 1, 1977

By R. L. Taylor, S. D. Abbott

"INTRODUCTION Mines are filled with a mixture of gases, some of which are toxic, flammable, explosive. Others can be early reporters of potential problems. It has previously been shown that analysis by gas chromatograph can the most accurate conventional analytical tool for common mine gas mixtures when used correctly. There are some other detection methods (e.g hand held sensors), but they do not detect many situations which are immediately dangerous to life or health (IDLH). Examples include explosive hydrogen mixtures, toxic carbon dioxide levels, and some explosive mixtures of methane with oxygen. (Reference our previous paper). There are several reasons for mines to consider onsite GC analysis. (1) Timeliness of results. Samples can be taken and analyzed immediately. Samples do not have to be shipped to a lab and wait for results. (2) Ability to run greater number of samples a lower for the same cost. This allows mine to increase the number of samples taken to be more informed about the gases/conditions of the mine without the worry of financial constraints. (3) Fewer sample media needed, and there is no wear and tear or cost from shipping them offsite. When samples are shipped offsite, those sample media cannot be used to take until the lab returns them when the analysis is done onsite, the sample media can be used again almost immediately. However there are several challenges associated with using GC to analyze mine gas samples onsite. To date there has been a clash of the requirements for a successful analysis, the capabilities of the technology, and the practicalities of implementation. The purpose of this paper is to discuss some of the difficulties in getting accurate reliable data and doing so in an economic way. This whole measurement activity is a cost center for a mine, so there are economic concerns for the mine to address. These concerns are mainly staffing costs, capital costs, maintenance, and consumables costs. A properly staffed and equipped analysis lab, including burdened overhead, costs about $500K per year. At a sampling rate of 10 per day, this is about $140 per measurement for a proper onsite lab."

Jan 1, 2016

By Jim Avraamides

Historically, much of Western Australia's gold production has come from the refractory sulphide-telluride ores located in Kalgoorlie's Golden Mile. Most of the recent gold boom has been associated with low grade, open pit free-milling oxide deposits. Primary sulphides are commonly encountered at depth and in many cases are highly refractory. Different approaches to the problem of recovering go1d from these ores have been adopted subject to local conditions both technical and environmental. The least preferred option is the preparation of a gold- rich flotation concentrate which is shipped to a smelter. Roasting of flotation concentrates can be practised in certain remote locations where sulphur emissions are tolerated. Fine grinding of flotation concentrates followed by direct cyanidation is another popular approach although this often leads to fouling of carbon by flotation reagents in the adsorption section and high soluble gold losses.

Jan 1, 1989

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By M. D. Chatham

Revolutionary electronic monitoring and control systems provide a gold mine of diagnostic and prognostic information. Lower cost per ton results from timely operator action, increased visibility of information to production and maintenance personnel, and better fleet management. When information is effectively integrated into fleet management systems lower costs result from higher availability, longer component life and reduced repair cost. This paper will present the objectives of the Caterpillar Vital Information Management System (VIMS) and provide actual examples of successful use.

Jan 1, 1995

By John C. Wangaard

A method of raising by use of a cage has been used with considerable success at the Cary Mine, Hurley, Wisconsin, on the Gogebic Range. The Cary Mine is owned by the Odanah Iron Company, Pickands, Mather and Company, Managers. This method is known to have been used previously at Tennessee Copper and probably in other districts. The Cary Mine was engaged in deepening the main shaft from the 34th to the 37th level. To accomplish this, and to facilitate development, a ventilation shaft 930 feet north of the main shaft was sunk from the 34th to the 37th level and crosscuts were driven on the 35th, 36th and 37th levels to the main shaft location, These levels are at 200 foot verticalintervals. All of this work was done in granite and the majority of the workings were not timbered. The next step was to get a raise through from the 37th to the 36th level, and from the 36th to the 35th level, which would later be stripped to full shaft size. Several methods of raising were considered including double-compartment cribbed and two single raises interconnected at regular intervals, but the cage method was chosen as it appeared to be a safe and efficient operation. The method in general consists in the use of a drill hole between levels through which to pass a hoisting rope to raise and lower a light cage.

Jan 1, 1958

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

A knowledge of airway friction factor (K-factor) is necessary to designing mine ventilation systems for least cost and optimum effectiveness. The friction factor used must be accurate and reliable to estimate correctly roadway resistances and pressure sources for required flows. Though the resistance to flow offered by mine airways has been an object of study over the last half century, no accurate relation has yet been established from which the prediction of the resistance of a projected airway can be made. In Kentucky, only limited and incomplete data on local K-factors are available. Therefore, there is a need for field investigations to determine these values in-situ for existing mining conditions. The author describes a study concerning K-factor that was carried out in ten coal mines, located in eastern and western Kentucky. The results of these investigations are presented in both tabular and graphical form.

Jan 1, 1991

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By Isobel Clark

Geostatistical methods of estimating ore reserves and other spatial phenomena are becoming increasingly wide spread in their use. Properly applied, Geostatistical estimation falls into two stages -- the "modelling" of the spatial variability within the study area; and the use of this spatial model to provide an appropriate estimation technique. The first stage usually consists of construction and interpretation of semi-variogram graphs, and the second is the development of the corresponding Kriging method. Because of the apparent subjectivity inherent to the first stage of a geostatistical analysis, attempts have been made to provide methods of "testing' whether a particular semi-variogram model (say) adequately represents the study area. Increasingly, the choice of model is being justified by a process known as "Cross Validation'. With this approach, the analyst uses a partial data set to estimate values at actual sampled positions. "Real" and "estimated" values are then compared in such a way that the model can be accepted or rejected. This paper discusses the process of cross validation in some detail, using case studies as examples. Some problems with the technique are illustrated and discussed.

Jan 1, 1986

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By Francois E. Heuze

Excavation of large rock caverns is a stepwise process. Whether one uses a heading and bench method or a multiple drift system, the use of excavation steps enables one to introduce the reinforcement, such as bolts or shotcrete, at the earliest possible stage. Knowing the spatial distribution and properties of rock materials and geological discontinuities, the cavern geometry and its reinforcement must be optimized. The finite element method of analysis is a powerful tool for such optimization. However, the models are only as good as their ability to account realistically for the physical attributes of the prototype and for the excavation sequence. They must include the following: - ability to model an incremental construction process. Thus requires the use of "Restart" procedures where displacements and stresses from a previous equilibrium are saved for the next step. - ability to model non-linear rock material behavior; in particular, the post-peak behavior of the rock which retains a residual strength when con-fined. The stability of many under-ground structures rests with the "broken" rock carrying significant loads. - ability to account for the non-linear behavior of geological discontinuities. These are two-fold. First, up to peak, non smooth rock joints will dilate. In a confined situation, dilation will increase joint strength by a consider-able amount (Obert, et al, Brady, 1971, Heuze,1978a), Then, beyond the peak, the joint also retains residual strength.

Jan 1, 1978

By J. T. Crawford

A comprehensive strategic planning model has been developed for the phosphate strip mining and chemical operations at White Springs, Florida. The computerized model covers ore body modeling, production simulation and financial analysis. Several innovative features in the model include using NPV techniques in ore body block economics, adapting the floating cone method to a floating template for generating dragline mining units automatically, using interactive graphics for designing mining units, and a dragline move economics algorithm for automatic scheduling of mining unit assignments and moves. Simulation of chemical plant production uses linear programming and concentrate inventory levels control mine operating schedules.

Jan 1, 1997

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009