Search Documents

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By J. Edwards

A new, world class dump leach, solvent extraction, electrowinning plant for the recovery of copper comes on line in Chile. CODELCO-Div. Chuquicamata has added a new facility to their operations located in northern Chile. The plant demonstrates many unusual features including: underground collection of leachate, high copper tenors, extensive use of plastics and special corrosion resistant alloys.

Jan 1, 1989

By Dan Kump

This paper provides an overview of Barrick Gold's Bullfrog underground mine backfill program. The Bullfrog underground mine was a gold mine that primarily used the underhand cut-and-fill mining method. The first portal was established June 18, 1991, and mining continued until Dec. 29, 1998. This paper begins with a discussion of the events that took place to reach about 1.8 kt/d (2,000 stpd) of backfill. It ends with a commentary of what was learned. The Bullfrog experience suggests that there are two essential factors to a successful backfill program: a well-graded aggregate supply and proper placing procedures.

Jan 1, 2002

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By H. B. Comstock

This paper reviews the trends in supply and consumption of the principal magnesium compounds in the United States in relation to domestic requirements and world resources. The data are confined to these principal magnesium compounds: Magnesium chloride, magnesium hydroxide, precipitated magnesium carbonate, and magnesium oxide (commonly referred to as magnesia). The properties and uses of magnesium compounds are shown in various chapters of' the 2nd edition of Industrial Minerals end Rocks. 3/ The third edition of this reference is in preparation. A more recent description of properties, uses and sources of magnesium compounds appears in a Bureau of Mines publication.4/ The American Iron and Steel Institute and the Refractories Institute have published comprehensive data on the properties and uses of basic refractories. Many magnesium compounds are prepared by the producers to meet specifications set by individual consumers.

Jan 1, 1960

By J. A. Herbst

Successful transitions from micro- to macro-engineering are the keys to effective technology transfer between research and development organizations and industrial end users. At the same time, it has proven to be one of the most difficult tasks that the minerals industry has had to manage. Typically, developers of fundamental information concerning how mineral processing subsystems work have been academics and government scientists. These are the individuals giving the most important input to micro-engineering models that can benefit industrial operations. Publication is the usual route for "attempting" to transfer this technology to the end users. Unfortunately, with such publications, very little direct communication occurs concerning real industry needs or the future steps required to make the particular micro-engineering model useful. In the past, the industry has relied on in-house R&D groups and plant metallurgists to "translate" publications, to provide useful macro-engineering tools for plant applications. To some extent, engineering companies have also been asked to serve this function. However, these firms have been rather ineffective in this area since their conservative nature has caused them to look rather suspiciously at new technology. This approach to technology transfer has worked, albeit clumsily, for the last several decades. This communication system is now on the verge of total collapse due to conditions of the minerals industry. Mining companies can no longer afford the significant overhead expenses of specialized technical staffs. Universities are finding it extremely difficult to interest US students in mineral engineering programs, and funding for such programs is weak. Faculty members involved in micro-engineering research today tend to focus on pure (non-application-oriented) research.

Jan 1, 1992

By William C. Larson

The Bureau of Mines, as a result of its contract research program, is developing a retractable core bit for the wireline drilling system (Retractable Sit System, No, H0272004). The prime contractor, Longyear Company, Minneapolis, Minnesota, and the subcontractor, Doerfer Division, Cedar Falls, Iowa, have designed, fabricated, and are currently field testing the in-hole retractable bit system. he objective of the program is to develop a minerals exploration core drilling system that allows retraction of a worn out bit and insertion of a new core bit, without pulling the drill rods out of the hole. To date, the results of the project are encouraging, and the retractable bit contract is currently in the last phase of a four-phase program, which is on schedule and under budget.

Jan 1, 1980

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By J. R. Johanson

Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale because of larger so lids contact pressures, thermal shocks or unforeseen temperature excursions often cause full scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow property measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full scale design or existing plant modifications.

Jan 1, 1988

Effective tools are not only essential for the design of practical and efficient underground mine ventilation systems but must also play an integral part in the operation of the mine. One such tool is VUMA-coal ventilation simulation software. VUMA-coal is Windows-based and has been specially designed for the simulation of underground coal mines and includes user-friendly coal specific interfaces and three-dimensional graphics designed to facilitate in the construction and analysis of networks. VUMA-coal can be utilised during the design phase of new collieries, be used to conduct ?what-if? and optimisation studies, and be integrated into the ?day-to-day? ventilation related operations. In addition, VUMA-coal can be used to simulate dust and gas distribution in a ventilation network, as well as predict the impact of control measures. This paper describes the interactive VUMA-coal ventilation simulation software and its underlying design features and outlines a case study of how VUMA-coal has been integrated into Anglo Coal?s Ventilation and Occupational Hygiene Engineering [VOHE] department as part of the standard planning and evaluation process in their operational mines as well as long term planning and future mining operations.

Jan 1, 2009

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By Ken J. Richards

Industries dependent on pyrometallurgical processing generally find themselves facing a common set of problems, namely, serious environmental restrictions, heavy capital requirements for new facilities and for plant modernization, the certainty of rapidly escalating fuel costs, and the uncertainty of fuel availability. To remain competitive, it has become clear to industry that a new dimension of attention must be given to assuring the maximum performance from plant facilities already in place and from those that are built in the future. In the last decade or so, in response to these needs, there has been an acceleration in the development of new pyrometallurgical process concepts. Their application, though spotty, is increasing. A common factor in this developing base of technology is the need for effective process control. Digital control is an indispensable element of meeting the challenge. We cannot make the point, however, by looking to a general survey of instrumental control of pyrometallurgical processes. Computer control is in its awkward adolescence. Its application is so new that only isolated applications can highlight the trends. For this reason, the authors have chosen to focus on the nonferrous smelting industry to illustrate the status of pyrometallurgical processing and control. We believe this approach will best meet the interests of most readers of this edition and the background of the authors.

Jan 1, 1979

By Ronald S. Tanaka

In the planning stages for a dozen years, the 9.11 mile long Mount Macdonald Tunnel is the focal point of the $600 million dollar Rogers Pass Project. The paper will discuss the construction of the tunnel that is being carried out from both ends. The eastern portion contractor has used a tunnel boring machine to excavate the upper part of the tunnel and at the west end contractor selected the conventional drill and blast method. A ventilation shaft located near the mid point is the main part of a ventilation system unique in the Western Hemisphere.

Jan 1, 1987

By Edward S. Hsia

Pluor Utah has been closely associated with the engineering and construction of earth bottom thickeners for porphyry copper operations, for the counter-current decantation circuit of a gold cyanide plant and similar applications in mineral processing. During the past 13 years, some 18 of these thickeners have entered service and the bottoms have proved to be watertight structures with no particular problems encountered. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction. This paper describes the successful application of engineering and construction techniques for a number of these thickeners.

Jan 1, 1977

By D. McSwain-Santos

Soda ash is the trade name for sodium carbonate, a chemical refined from the mineral trona or naturally occurring sodium carbonate-bearing brines (both referred to as natural soda ash) or manufactured from one of several chemical processes (referred to as synthetic soda ash). It is an essential raw material in glass, chemicals, detergents and other important industrial products. Production U.S. soda ash production during 2004 increased to10.9 million Mt (12 million st). Five companies comprised the domestic soda ash industry. Four were in Wyoming operating five plants. One was in California with one plant.

Jan 1, 2005

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By C. Stacy

The mining industry is changing rapidly. Competition among OEM and aftermarket vendors increases dramatically each year as a result of mergers and acquisitions, and especially technology advancements in the mining industry. Adding value to mine operations by delivering technical value and differentiation is becoming more subtle and more difficult to accomplish. Because of this, identifying and protecting intellectual property has become more important to the product development, engineering and marketing/sales continuum than it had been in the past. How companies protect intellectual property and determine the value of those assets is critical to the sustainability and differentiation of technology providers in the mining industry.

Jan 1, 2012

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By D. K. Denton, M. J. Friedel, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep ( > 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Feb 24, 1997