Search Documents

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By W. E. Hale

The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Programme (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature: during approximately six weeks an orientation survey, involving, geology, geophysical surveying, and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Sto. Nino (Fig. 1). The Sto. Nino study demonstrated (Hale and Govett, 19677 Govett and Hale, 1967) the feasibility of geochemical prospecting relative to other exploration methods for the location and delineation of disseminated copper occurrences, the major source of metal in the expanding mineral industry of the Philippines. A vein occurrence at Suyoc (Fig. 1) was similarly subjected to

Jan 1, 1968

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

Those who have had an occasion to apply geostatistics to the estimation of ore reserves are familiar with the conventional approaches of estimating average grade of quality values for arrays of regular grid squares or blocks. Further, the technology to perform geostatistical analysis and prediction for irregular two-dimensional areas has been available in a practical, readily useable form for some time. However, the generalization of this technology into three dimensions has been hampered by lack of a suitable geometrical characterization for realistic, three dimensional shapes and volumes. The extension of these estimation techniques into three dimensions has now been made possible by a successful integration of the volume modelling capabilities of 3D Component Modelling with proven 3D Geostatistical Techniques. The result is a powerful new technique for mineral ore reserves estimation in a practical, useable form. The technique allows direct geostatistical estimation of grade and quality values for precisely defined, irregular, realistic, geological, and mining shapes or volumes. This paper describes the two technologies, their integration and their application in practice to the estimation of mineral ore reserves. The paper closes with a discussion of the benefits provided by the new approach, in terms of accuracy, efficiency and practicality.

Jan 1, 1991

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass-produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982

By L. Adler

In spite of distractions from glam-our areas (ground control, computers, etc.), excavating and bulk handling in mining remains paramount but is now undergoing dramatic advances. The massive intervention of mining and civil engineers as "engineer-users" into the tight, exclusive, and specialized bond between the equipment operator ("operator-users") and the manufacturer (mechanical engineers "and sales "reps") has now occurred. Three developments have accelerated this: 1) larger, more costly, complex, specialized, and innovative equipment; 2) a more profound understanding of the equipment, operations, and working conditions (encumbered space); and 3) a concurrent thrust into "high-tech," (automatic and remote controls, sensors, automation, artificial intelligence, and even robotics) and human factors (workload intensity, work-station design). This has produced a well-defined professional discipline, including construction and even military engineering. The mine plant, and to a lesser extent, the mine face, is now being monitored. Equipment conferences, journals, and centers at universities and agencies have multi-plied. The discipline's impact on future mining now becomes more apparent.

Jan 1, 1988

By R. N. Chakravorty, R. J. Kolada

Explosions of methane in coal silos and coal ships is an ever present hazard. Recent investigations have shown beyond question that considerable accumulations of methane do occur in coal storage silos and numerous recent explosions in coal transport shipping strongly indicates that the same conditions also exist in ship storage holds. Investigations have shown that the main concentrations of methane occur within the actual coal pile. Within this region normal silo and ship ventilation systems are ineffective. The main 1ine of defence is therefore to exclude potential sources of ignition or to place the coal in an inert atmosphere, or both. This paper presents the results of a methane survey of all operating silos in Western Canada. These results demonstrate that a serious and widespread hazard of explosion exists. This paper also discusses various methods by which this hazard may be reduced including methods of venti1ation, inertization, microbiological control and early warning systems.

Jan 1, 1987

By R. J. Heath

Potash, the general term for potassium salts used as fertilizers, is one of the essential growth nutrients (together with nitrogen and phosphates) required by all living things. Total world consumption of potash for fertilizer use - almost all of it in the form of potassium chloride - amounted to an estimated 47 million short tons in the 1979/80 fertilizer year*. While there is some limited demand for potash for a variety of industrial applications, this amounts to only 3 or 4 per cent of total world demand, and the potash business can be viewed as essentially a fertilizer business. Total available world potash production in the 1979/80 fertilizer year also amounted to approximately 47 million tons. There are two large potash producing countries - Canada and Russia - and a number of other countries where production is significant - East Germany, West Germany, the U.S.A., France, Israel and Spain. Production volumes are shown in Table 1.

Jan 1, 1980

By Wen H. Su

This paper examines the intrinsic mechanisms of cutter roof by combining field investigation, laboratory testings, underground instrumentations, and numerical modelling. Cutter roof developed during the development of a set of longwall panel entries in a West Virginia coal mine was presented as a case study. Mining alternatives applicable to the mine are recommended. Cutter roof occurred in two other West Virginia coal mines were also investigated Detailed comparisons were made among the three cases. As a result of the extensive investigation, intrinsic mechanisms of cutter roof failures under various conditions are presented from the practical and theoretical points of view.

Jan 1, 1985

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content, and material type. Permafrost slope fails due to solifluction, disturbance of ice-rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures, many steels lose most of their normal ductility and toughness (resistance to brittle fracture). This paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1988

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By E. K. Albert

Title IV of the 1977 Surface Mining Control and Reclamation Act (SMCRA) provides for an abandoned mine reclamation fund. This fund, taken from fees collected from operating coal mines, provides capital for the reclamation process. The Act directs the Office of Surface Mining (OSM) to collect the fees based on coal production. Monies from the abandoned mine lands (AML) fund are distributed through two programs. The first provides OSM with capital to use in emergency situations resulting from abandoned mine sites and reclaiming high priority sites in states without established AML programs. The second distributes the money through a state's AML program in the form of grants. To provide for a flexible and customized selection procedure for AML projects, a management information system (MIS) that combines scientific selection procedures is being developed. This system employs objective and subjective methods developed in systems research in recent years. The MIS component is an essential part of any selection process involving large numbers of potential projects. It must contain all the necessary project parameters that can be applied to the selection of projects whether or not they are to be used in the immediate selection criteria. In addition, variable selection criteria will allow ‘what if’ types of inquiries for comparison of differing selections and benefits.

Jan 1, 1990

By B. A. Hancock

It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rup- ture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differ- ences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding- classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective floccula- tion separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 1, 1987

By A. Lashagri

This paper presents research results on assessment of environmental impact of digging and loading equipment in surface coal mining. Environmental impact is accessed through the equipment exhaust and dust emissions, and sound level. Exhaust emission is related to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx), and volatile organic compounds (VOCs). Dust generation is expressed through the particulate matter PM10 and total suspended particulate matter (TSP), while sound is presented through the sound pressure level. Modeling of environmental impact of digging and loading equipment is conducted in Microsoft Visual Studio.NET software package. This research is a part of a boarder project on development of software system for the selection of productive, cost-efficient and eco-friendly mining systems, which is sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). The research work presented here may be used by mining professionals to aid in quantifying environmental impact of digging and loading equipment and determinate strategies for reducing its overall impact.

Feb 27, 2013

By S. Jennings

The Red Dog zinc-lead-silver deposit is located in the DeLong Mountains of the western Brooks Range in northwest Alaska. The region is located 145 km(90 miles) north of the village of Kotzebue (Fig. 1).Red Dog’s current resource base is 143 Mt (157 million st) averaging 16.1% zinc, 4.3% lead and 83g/t (2.4 oz/st) silver. It is contained in four structurally separate deposits— the Hilltop, Main Deposit, Aqqaluk and the newly discovered Paalaaq deposit. Recent exploration for the Aqqaluk and the Paalaaq deposits has contributed to Cominco American’s understanding of the detailed structural geology of the district and its role in the placement of individual ore bodies.

Jan 1, 1999

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By Jeff Fontana, Daniel Ebin, Eric Westergren, William Currier

The PMott MacDonaldlane Train Tunnel West Extension (PTTWE) Project at HartsfieldJackson Atlanta International Airport includes the extension of the existing automated people mover system and terminal renovations at the baggage claim station. To assist with design, pricing, and assessment of risk on this progressive design-build project, 3D design models were prepared to increase visibility into realities of construction. This paper will focus on the original intent of the models and explore the additional, unforeseen value they provided throughout the design and construction process.

Dec 1, 2022