Search Documents

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By Jeffrey J. Schwoebel, Jianliang Li, Daniel J. Brunner

A United Nations (UN) administered degasification technology transfer project, funded by the Global Environmental Fund (GEF) is underway at the Shihao Mine of the Songzao Coal Mining Ad- ministration in the province of Sichuan, Peoples Republic of China. This mine exploits multiple seams at depths ranging from 300 to 600 m below surface. In-seam boreholes and frequently spaced in-mine vertical boreholes, developed from underlying galleries constructed specifically for this purpose, currently degasify the seams in advance of mining at the Shihao Mine. Because of ventilation system constraints and the in-situ gas con- tent, longwall mining of the coals at this mine could not proceed without some form of pre-mining degasification. This paper presents a simulation based degasification plan of long, in-seam horizontal boreholes for the Shihao Mine. Simulations with a coalbed reservoir program assessed time dependent degasification characteristics of both vertical and in-seam horizontal boreholes. The simulations used input data from reservoir and desorption tests conducted at the mine site. The results produced system design nomograms to assist mine engineers in defining the appropriate borehole spacing necessary to degasify the seam in the time available for pre-mining drainage. The predicted effectiveness of the current vertical degasification scheme was compared with that for a horizontal borehole program and served as the basis for the recommended in-seam borehole configuration for the project at the Shihao Mine. The horizontal borehole degasification program requires substantially less gallery and borehole development than the present vertical degasification scheme.

Jan 1, 1997

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1987

By W. Hitchcock

To enable the analysis of stability for a mine feasibility study a variety of geotechnical engineering parameters need to be obtained. At the early stage of a project it is usual for those responsible for the study to require a wide spatial distribution of RC holes in order to define a resource at the lowest possible cost. By the time a geotechnical study has commenced drilling priorities have usually switched to improving the definition of a resource, by drilling with diamond coring methods in the central area of the main orebody. The usual timing for geotechnical data collection is therefore after a wide distribution of holes have been drilled but which contain little geotechnical information. Conventional methods employed usually involve estimation methods, including book values and examination of disturbed core, or expensive additional drilling. With downhole geophysical methods we can economically take advantage of existing holes to obtain continuous values for density, defect orientation and ranking, elastic modulus values, unconfined compressive strength estimates and fracture frequency. This paper presents the results of a geophysical study and discusses the advantages and potential pitfalls of the method as compared to conventional methods of data collection.

Jan 1, 1999

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

By H. T. Miller, L. M. Scott

Radiation exposures in Uranium operations may result from external beta-gamma radiation emitted by Uranium and its progeny, internal exposure to alpha and beta radiation due to the inhalation and ingestion of Uranium ores, Radon gas, and Radon progeny in mine, mill, and laboratory atmospheres and from the contamination of environmental working surfaces and clothing by Uranium-bearing compounds and ore. This paper summarizes occupational experience with reference to the exploration, surface mining, underground mining, milling and transport of Uranium by one company in the U.S. and Canada.

Jan 1, 1981

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By Armstrong

This is a world of change and has been from the beginning. There are constant efforts on the part of natural forces to wear down the high spots and fill in the low spots. Wind and water over eons of time tunnel through obstacles and build windways and waterways to make movement of air and water easier and more efficient. It is a natural, never ending, ever changing continuing effort. Man in his struggle to survive, and to progress, has had to adapt the terrain of the earth to fit his needs the best he could. First, he used natural caves to protect him from the elements; then he learned how to build earth and rock-moving tools from antlers, bone, rocks, and sticks and adapted his cave to increase his security and provide better protection from heat and cold and from his predatory enemies. As his numbers increased, so did the necessity of further adapting his environment to accommodate his needs. Water was usually not available when and where needed, especially in the desert areas where civilization developed, and long tunnels were drilled to intercept ground waters and lead them to underground caves carved out of soft limestone. Most of the tunnels of early man were to bring water from where it was to where man needed it. Then, as now, as man increased his chances for physical survival, he turned to the quality of life -- and this reflected in the concern for life after death. This lead to the elaborate shafts and tunnels for the protection and prservation of the more affluent noblemen and pharaohs of the early Egyptian civilization. Man used the underground for the stable temperature and for protection and safety.

Jan 1, 1974

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By W. G. Lacy

Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the and to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area prompted by foundation failures and breaking, of buried service lines serve to illustrate some of these relationships between the geological environment and history, and engineering problems.

Jan 1, 1963

By Kent G. Homewood

The well-being of any company is directly related to the well-being of its employees and to the effectiveness with which the personnel resource is managed. In an era when personnel management has steadily become more complex, there is an increased awareness of employee information systems at all levels of management due to: (1) regulations enacted by federal, state, and local government agencies; (2) technological advances within the mining industry which have resulted in the requirement for highly skilled personnel; (3) increasing concern for the confidentiality of employee information; and (4) management's need for information for planning purposes to control costs and for early recognition of trends and potential problems. In the past it was sufficient to maintain records manually. Today computers are necessary to provide information on short notice and effectively manipulate large volumes of' data. This discussion will describe the following aspects of employee information systems: (1) collection and maintenance of information, and (2) applications which include employee health, salary administration, management re- sources, and labor negotiations.

Jan 1, 1979

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

The algorithm presented in this study determines the combination of fans that provide all working districts of a mine with predefined airflows at the minimum operating cost. It is based on an existing ventilation simulator, VNETPC, and a set of linear equations associating fan pressures and the added resistance of regulators. Two assumptions are undertaken: (1) fan locations are predetermined and (2) the number of working districts is equal to or greater than the number of fans. By means of this algorithm, the optimal solution to an n fan ventilation system may be found after n + 1 simulation runs.

Jan 1, 1987

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984