Search Documents

By Lawrence M. Zanko

Eighteen coarse taconite tailings samples were collected in 2000-2001 from five western Mesabi Range taconite (iron ore) operations located in northern Minnesota, i.e., EVTAC, Hibbing Taconite (Hibtac), USX Minntac, Ispat Inland (Minorca), and National Steel Pellet Company (NSPC), to test their physical, geological, chemical, and mineralogical properties [Zanko, L.M., Niles, H.B., Oreskovich, J.A., 2003. Properties and aggregate potential of coarse taconite tailings from five Minnesota taconite operations, Minnesota Department of Transportation, Local Road Research Board, St. Paul, MN, Report No. 2004-06 (also as Natural Resources Research Institute technical report, NRRI/TR-2003/44)]. The goal was to assemble a body of technical data that could be used to better assess the potential of using a crushed taconite mining byproduct like coarse tailings for more widespread construction aggregate purposes, primarily in roads and high¬ways. An important part of the mineralogical assessment included X-ray diffraction (XRD) analyses and microscopic (polarized light microscopy, scanning electron microscopy, and transmission electron microscopy, i.e., PLM, SEM, and TEM, respectively) evaluation of the size and shape (morphological) characteristics of potentially respirable microscopic mineral particles and fragments. Quantitative mineralogy, based on XRD analyses, showed that the dominant mineral in all samples was quartz (55-60%), followed by much smaller amounts of iron oxides, carbonates, and silicates. Specialized microscopic analyses and testing performed by the RJ Lee Group, Monroeville, PA, on both pulverized (-200 mesh, or 0.075 mm) and as-is sample composites showed that no regulated asbestos minerals or amphibole minerals were detected in the western Mesabi Range samples. A small number (26) of non-asbestos and non¬amphibole mineral cleavage fragments/mineral fibers were detected by SEM out of 1000 fields analyzed, but most were identified as min¬nesotaite and talc, silicate minerals common to the Biwabik Iron Formation. Amphibole minerals, absent in coarse tailings samples from the five western Mesabi Range taconite operations, were present in a single eastern Biwabik Iron Formation sample collected in 2003 for Lake County from the Cliffs Northshore operation in Silver Bay, MN. Importantly, the Superfund Method for the Determination of Releasable Asbestos in Soils and Bulk Materials [United States Environ¬mental Protection Agency (USEPA), 1997. Superfund method for the determination of releasable asbestos in soils and bulk materials, EPA 540-R-97-028, U.S. Environmental Protection Agency, Washington], as modified by Berman and Kolk [Berman, D.W., Kolk, A.J., 2000. Modified elutriator method for the determination of asbestos in soils and bulk materials, Revision 1: Submitted to the U.S. Envi¬ronmental Protection Agency, Region 8, May 23, 2000] failed to generate any protocol fibers, i.e., fibers longer than 5 µm and thinner than 0.5 µm, from either the western coarse tailings samples or the single eastern Biwabik Iron Formation sample. The combined findings suggest coarse tailings and other taconite mining byproducts should be treated with the same common sense safety and industrial hygiene approach practiced for all mineral-based materials that have the potential to generate respirable dust. © 2007 Elsevier Inc. All rights reserved.

Jan 1, 2007

By John B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with alum. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1984

The most important event affecting the United States coal industry in 1993 was the strike by the United Mine Workers of America (UMWA). This was a series of selective strikes, beginning with a strike against four Peabody Holding affiliates on Feb. 2, following unsuccessful contract negotiations between the UMWA and the Bituminous Coal Operators' Association (BCOA). Although that strike ended on March 3, the failure to reach a new contract agreement led to walkouts at several Midwestern mines on May 10. During the summer, the strike expanded to include mines of 13 companies in seven states including Ohio, Pennsylvania, Illinois, Indiana, Kentucky, Virginia and West Virginia. About 17,000 miners were idled during the strike. As the prospects for a settlement diminished, the Secretary of Labor appointed a federal mediator. The mediation resulted in a five-year contract. In addition to increases in wages and pensions, it was agreed that 60% of new job openings would be filled by laid off and active UMWA miners. In return, companies won the right to establish more flexible work rules and scheduling of miners. While some health care benefits were expanded, the agreement established a new health care system that was designed to reduce costs. Preliminary Energy Information Administration (EIA) data indicate that US coal production fell by 5% in 1993, to 859 Mt (947 million st) (Table 1). The strike was one of the primary causes of the decline in production. Another significant cause was a 27% decline in coal exports. Also, a very small displacement of domestic coal production resulted from a rise in coal imports.

Jan 1, 1994

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By Robert B. Scott

The Dents Run Demonstration Project near Morgantown, West Virginia, was a cooperative venture involving the U.S. Environmental Protection Agency (EPA), the Water Resources Division (WRD)(1) of the West Virginia Department of Natural Resources (DNR), and the Christopher Division of the Consolidation Coal Company (CONSOL). The object of this project was to demonstrate pollution control methods and to clean up a 37.8 sq km (14.6 sq mi) watershed severely polluted by coal mine drainage. A study entitled, "Water Infiltration Control to Achieve Mine Water Pollution Control" (EPA-R-2-73-142),(2) was conducted by the Cyrus Wm. Rico Division of NUS Corporation for the grantee to determine the feasibility of utilizing remedial techniques to improve the Dents Run water¬shed. This study showed that the Dents Run watershed was discharging as much as 6,870 kg/day (15,100 lb/day) of acid; 1620 kg/day (3,560 lb/day) of iron 17,250 kg/day (38,000 lb/day) of sulfates; and 29,500 kg/day (64,900 lb/day) of total dissolved solids into the Monongahela River near Morgantown, West Virginia. This pollution was caused by the combination of borehole pump discharges from active underground mines, runoff from abandoned strip mines, and runoff from refuse dumps.

Jan 1, 1977

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By Peter Loehr

Full-face tunnelling machines were introduced into German coal mines 12 years ago. It was aimed to utilize these highly efficient systems to drive mine tunnels in rock so that the large demand for development work in some mines could be met. A characteristic feature of coal deposits in Germany - and particularly in the Ruhr Area - is a thick overburden strata. Access is therefore only possible through vertical shafts. A network of horizontal drivages leading from these shafts open the deposits between the different mine levels. The hardcoal-bearing formations are multi-folded and heavily tectonically stressed. Apart from a few extensive fault zones there are many single faults of different natures in the carboniferous strata. During the course of decades coal mining has penetrated to ever increasing depths. Nowadays coal is mined from depths of between 600 m and 1,200 m. The effects of ground pressure in connection with extremely varying rock strengths and high temperatures are particular difficulties which have to be overcome during drivage work. The first full-face tunnelling machines to be applied in the mines had originally bee deigned and developed for tunnelling projects. Not only the machines themselves, but also the back-up equipment had to be adapted to meet the special demands of German coal mines.

Jan 1, 1983

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

The advantages of quantitative environmental risk assessment techniques over the more commonly used qualitative approach is widely accepted. One important parameter related to the level of risk is the extent and geographic spread of pollutants. Geographic Information Systems (GIS) provide a powerful and highly flexible tool that increases the sophistication of the risk assessment methodology. Through spatial representation, the estimated risk becomes more comprehensive, thus facilitating the decision making process. In addition, valuable qualitative information can be incorporated into the risk assessment procedure with the help of GIS. This paper illustrates a methodology for quantifying risks posed to human health, by exposure to contaminated land, in a manner, which gives a measure of the uncertainty in the assessment and preserves the spatial distribution of the risks. The case study utilised to illustrate the methodology is a large industrial area around a number of decommissioned minerals production and processing sites with known high heavy metal loads at Lavrio, Greece. The spatial distribution of Pb concentration in soils was derived from 425 soil samples collected over a total area of 120 km2. Indicator kriging was used to quantify the spatial distribution of the risk and related uncertainty and the results displayed in map form using GIS.

Jan 1, 2003

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By C. A. Rowland

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The basic principles learned from wet grinding rod mills that were used in the application of dry grinding rod mills are 1. It is possible to extrapolate the performance of 5' and 6' diameter wet grinding rod mills into larger diameter rod mills with the larger mills performing as predicted. Wet grinding rod mills as large as 14' diameter (inside shell) by 20' long using 19.5' long rods are in use operating satisfactorily. 2. Wet grinding rod mills generally grind more efficiently when the fines are left in the mill feed than when the fines are removed from the feed. 3. Wet grinding rod mills produce little tramp oversize and generally can be operated in open circuit except when very close control on the top size in the product is required. When operated in closed circuit, the circulating load is normally less than 100%. 4. The power required for the desired grind can be accurately determined from the work indices obtained from rod mill grindability tests on the material to be ground. Where required it is necessary to, apply inefficiency factors for oversize feed and for larger or smaller than normal- ratios of reduction. Recent applications for rod mills have developed where it is required that dry grinding be used. These recent applications cover the grinding of 1. Lead sinter, lead slag and limestone. 2. Iron ore. 3. Silica for making glass sand. 4. Cement clinker. 5. Coke.

Jan 1, 1968

Many of the deeper ore reserves in current gold operations as well as new gold deposits consist of refractory ore types. As process development for these mineralizations remains time-consuming and costly, minimization of exploratory testwork and the early identification of feasible process routes is critical. Since most of the processing parameters are related to the mineralogy of the ore (Marsden & House, 1992), thorough mineralogical analyses during exploration and development phases have become a technical and economical requirement. The determination of mineralogy-related processing parameters and especially the gold mineralogy is even more important for these ore types because refractory gold ores consist of many transitions from partially leachable to totally refractory. In addition to sulfide and gangue encapsulation, various other refractory conditions may exist. Together with accessory mineralogical detriments (e.g., alteration/ slimes, reagent consumers, scale formation, mineral preg robbing) they may complicate process selection and hamper optimal plant operation.

Jan 1, 1993

By Z. Hyder

Simulation and modeling is powerful tool to analyze real time data and can be used to analyze different scenarios using appropriate software that may reduce need of infield data collection process and can predict reasonably accurate results. In this paper the real time data of a mine is used to simulate and model the stresses on the pillars and evaluate the pillar strength and safety factor. The material properties assigned to the model are obtained by testing the representative samples taken from the selected locations of the mine. The mine under investigation has 50 ft wide pillars and 50 ft wide rooms under an average overburden of 650 feet. The effect of reduced pillar dimensions and increased roof span on overall stability of mine and extraction ratio is analyzed using LaModel [1] software. The predicted results of the reducing pillar size are analyzed to compares the current mining practices with the optimized room and pillar size to get better extraction ratio without comprising the safety.

Jan 1, 2011

By M. Karmis

The Virginia Center for Coal and Energy Research is leading an interdisciplinary coalition to identify potential carbon sequestration sinks in unmineable coalseams as part of the U.S. Southeast Regional Carbon Sequestration Partnership. The Virginia Center for Coal and Energy Research and the Eastern Coal Council are leading education efforts for the project, as well as specific outreach efforts in Central Appalachia in order to develop a process for stakeholder education and engagement in sustainable energy.

Jan 1, 2007