Search Documents

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By Q. X. Yun

This paper presents a new approach to optimize the transportation system in open-pit mines. The new approach employs artificial intelligence, fuzzy sets, dynamic programming and CAD technique to determine the transportation system. The determination consists of 4 phases: initial selection, road alignment, final decision .and open-pit drawing.

Jan 1, 1992

By N-h. Mao

We applied kriging (geostatistics) to interpret the structure of basement rock in Yucca Flat, NTS from borehole data. The estimation error for 118 data is 81 m comparable with those based on both gravity and borehole data. Using digitized topographic data, we tested the kriging results and found that the model validation process (Thomas option) on data gave a fair representation of the overall uncertainty of the kriged values.

Jan 1, 1985

16.1.1-VENTILATION'S ROLE Importance of Ventilation and Environmental Control-Mine ventilation is necessary for the preservation of human life and for the conduct of operations involved in the underground extraction of minerals. It clearly is the most essential of the functions attendant to mining, yet it is auxiliary to the primary objective in mineral extraction. Ventilation in mining thus poses a paradox: ideally, it should be carried out with minimum interference with and cost to production operations, yet it is absolutely vital in providing adequate environmental con¬ditions to support mining. Deterioration of the atmosphere, along with rising ground pressure, imposes the ultimate constraint with depth in underground mining. Ventilation requirements and costs rise rapidly with depth. To preserve atmospheric quality under intense heat conditions, ventilation at great depths must be supplemented by air condition¬ing. Likewise, when mining at any depth under severe or excessive conditions of gas, dust or humidity, supplementary control measures must be employed. In recent years, environmental standards in mines have been raised substantially. While limits are based on human tolerance, increasing concern is being expressed for standards of human comfort. The reasons are economic, as well as humanitarian. Worker performance and longevity correlates closely with environmental quality. Further, adverse accident and insurance compensation rates are a consequence of unsatisfactory environmental conditions. No mining company can afford to be lax in its environmental and ventilation practices. Functions and Processes-Ventilation is the control of air movement, its amount and its direction. As a means of quantity control, it is one of the constituent processes of total air conditioning, the simultaneous control within prescribed limits of the quality, quantity and temperature-humidity of the air. Ventilation is the most common and most. important conditioning process employed in mines for air environmental control. In mine ventilation, air is coursed through the mine workings and openings themselves and, for auxiliary purposes, through vent tubing and ducts. Thus, many interdependencies exist between the mining system and ventilation method. In fact, the two often have evolved ,jointly, as in room-and-pillar extraction of bedded or tabular mineral deposits, such as coal. Ventilation in mines today is provided almost exclusively by large fans, although air flow may result due to natural (thermodynamic) conditions. As mines increase in depth, size and complexity, demands on the ventilation system to maintain more stringent standards of environmental quality likewise rise. On the other hand, never have the technology and resources of the mining industry to cope with environmental problems been so well developed as they are today. In spite of rising costs, it is unlikely that further progress in mine ventila¬tion and air conditioning must await technological breakthroughs. 16.1.2-NATURE OF THE MINE ATMOSPHERE Air Mixtures-Air is a gaseous mixture comprising the natural atmosphere at the surface of the earth. Thermodynamically, it may be thought of as a mech-

Jan 1, 1973

By John B. Comer

Compelling evidence indicates that at least the plateau bauxite of northern and central Jamaica formed from volcanic ash. The predominance in plateau bauxite of zircon grains younger than the host limestones and the relative abundance of zircon grains having idiomorphic form support a direct ash-fall origin for much of the bauxite parent material. Based on revised mass balance calculations, not enough of the middle Eocene to lower Miocene host limestones have been dissolved to make an important contribution to bauxite. Likewise, the pre-middle Eocene rocks of Jamaica have made only a very small contribution to plateau bauxite; they may have made a more significant contribution to the graben bauxite of southern Jamaica.

Jan 1, 1984

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By B. Salopek, D. Rajkovic, D. Rumenjak

Among other types of sustainability indicators, linguistic variables have been proposed. During the past few years considerable effort for using the fuzzy logic and linguistic variables (LVs) in environmental decision-making for the mineral industry has been made. The linguistic variables defined could, among others properties, describe the property of acceptability for environment for various environmental indicators. Some proposals for construction of such variables are based on administrative decisions from environmental impact assessment procedures for mining, which provide information for acceptability of quality kind for environment (e.g. obtained from public participation, experts, environmental administration). The measures of evidence for construction have to be based on sets (not only on the members of sets). The administrative decisions with their statements and explanations could be considered as such sets. The measures of evidence appropriate are plausibility and belief measures. Using the more elaborated methods from the theory of evidence, the better estimation of those measures could be achieved. The methods of constructing the linguistic variables, previously suggested and based on obtained measures, are also discussed.

Jan 1, 2011

By W. Robert Power

Stone is considered by many to be the premium material for beauty and durability in all kinds of construction. Its use dates to the dawn of civilization and only buildings made of stone have survived from ancient times. The use of stone relative to other materials declined from the beginning of the present century reaching a low point in the third quarter, but there has been a resurgence in the use of stone in construction during the past decade, due probably, to new techniques for producing stone, a greater recognition of its beauty and durability, and greater affluence among consumers. The aesthetic appeal of stone is attested to by the many attempts to simulate it in synthetic materials. Today, natural stone is considered by many to be the ultimate in aesthetic appeal, durability, and ease of maintenance. Consumption of dimension stone has increased dramatically during the past decade. The US Bureau of Mines reported that the total value of US consumption in 1978 was $1 13 million and that total imports were valued at $65 million in 1979 (Anon., 1980). In 1989 consumption of domestic dimension stone was valued at $208.3 million and imports at $525 million. This dramatic increase occurred after demand had decreased at an average rate of 2.5% in the two decades prior to 1978 (Anon., 1980). More than half of the imports come from Italy, but production of dimension stone has increased worldwide spectacularly. Meaningful statistics on dimension stone are hard to acquire. The finished piece of stone is a highly value-added product, but stone may be sold as rough blocks, sawed slabs, or finished product. The same piece of stone may therefore be sold and reported three or more times. Furthermore, although the quantity of stone is most commonly reported in tons, stone cladding is more often sold by the surface area and at the same price for different thicknesses. By any measure, however, the production and consumption of dimension stone has increased dramatically during the past decade. A significant indication of the resurgence of stone was the introduction of two new trade publications during the 1980s. Stone World (Tradelink Publishing Co., Inc., Oradell, NJ), introduced in 1984 is published monthly and Dimensional Stone (Dimensional Stone Institute, Inc., Woodland Hills, CA), introduced in 1985 is published monthly. Both magazines provide useful information on new technology, market trends, producing areas and companies, and other information not previously available.

Jan 1, 1994

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By Athorn Mary-Lee, Randall A. Snowdon

During the development of the Selby Coalfield, UK, a Robbins full-face tunnel boring machine (TBM) and a Thyssen Titan roadheader were used to drive a pair of parallel spine roadways. This paper presents a summary of the comparative operational and cutting performance of both the Titan road- header and the Robbins TBM. Statistical techniques were employed to identify relations between machine performance and geotechnical parameters.

Jan 1, 1986

By Gu Guohua, Hu Yuehua, Zhang Qin

The flotation behavior of pyrrhotite was investigated by using ethyl xanthate as a collector. Results showed that pyrrhotite had good floatability from pH 2 to pH 11, and poor floatability when pH was >12. The flotation of pyrrhotite was dependent on pulp potential on various pH values. The potential-pH range for pyrrhotite flotation was established. Cyclic voltammeny and FTIR spectroscopic analysis showed that the major adsorption product of ethyl xanthate on pyrrhotite was dixanthogen. The intensity of FTIR signals of dixanthogen adsorption on pyrrhotite and the anode current of a pyrrhotite electrode and flotation response of pyrrhotite are correlated with pulp potentials.

Jan 1, 2005

By M. J. Meulendyke, J. D. Purdue

Within the mineral processing industry, a range of grinding conditions exists which include semiautogenous grinding (SAG),rod milling, and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1990

By J. M. Baker

It seems appropriate here to open with a quotation from the great pre-Confucian philosopher Lao-tze: "The softest thing in the world dashes against and overcomes the hardest. There is nothing in the world softer or weaker than water, and yet for attacking things that are firm and strong there is nothing that can take precedence of it." I am happy to report that our system of mining has worked out, with minor modifications, as well or better than was predicted. This, in a period of rising labor and material costs, has been most gratifying. Gilsonite is a solid hydrocarbon which occurs in vertical fissures cutting the sandstone and shale beds of the Uintah formation in south¬eastern Utah. It is found in other parts of the world under similar occurrence but nowhere else is it now being mined commercially. The Gilsonite veins on entering the shale members of the Green¬river formation break into small veinlets separated by shale, These veinlets are not now economical to mine.

Jan 1, 1959

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979

By P. Bester, G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26million tons of ore of which 16 million is mined and milled onsite. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centred around the Pyroxenite ore. This will lead to substantial increases inproduction costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By K. Wangerud, B. S. Caruso

A water balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site, South Dakota, to evaluate risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for analysis of precipitation based on historic records, and for probabilistic estimation of annual and monthly runoff from primary disturbed/mining activity areas that currently requires, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/Excel add-in “@Risk” was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation, and groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2002

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers' catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997