Search Documents

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.' The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By Harry Parker

Resource and Reserve Audits Becoming Increasingly Common Types of Audits -Review of Methodology (‘Fatal Flaw’) -Due Diligence – (‘Sign Off’) -Endorsement – (‘QA-QC’) Suggested Standards in Red

Jan 1, 2003

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984

By Joseph Gildner, Donald J. Phelps, Jürgen Laubbichler, Christopher Tattersall, David McAllister

The Beacon Hill Station and Tunnels portion of the Sound Transit Central Link Project consists of one mile of twin rapid transit tunnels, an underground station, portals and ancillary works constructed in an urban environment. Presently under construction, the station will set a number of North American firsts including deepest soft ground excavation carried out using the Sequential Excavation Method (SEM).Located in highly variable glacial soil deposits ranging from soft, water bearing sands to stiff, slickensided clays, the station complex and running tunnels proved to be technically challenging during design. Meeting these challenges necessitated an extensive geotechnical investigation, a trial shaft, and state-of-the-art numerical analyses to develop ground conditioning, pre-support, excavation support and structural design. A comprehensive risk identification and mitigation program, and innovative procurement strategy were incorporated into the design and contract bid documents.

Jan 1, 2005

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By Andreas G. Mueller

Gold-silver and copper-gold deposits with high-temperature wallrock alteration of Ca-Mg-Fe-Al silicates occur in ca. 3.0 Ga old greenstone belts of the Yilgarn Block, Western Australia. The deposits are hosted by amphibolite-facies komatiites, basalts and BIF, controlled by ductile shear zones and located within the contact-metamorphic aureoles of composite granodiorite-granite batholiths. Disseminated sulfides and free gold form foliation-parallel ore zones in a gangue of anhydrous silicates (garnet, clinopyroxene, olivine), hydrous silicates (amphibole, biotite) and calcite. The deposits may be classified on the basis of their dominant economic metals as: 1(1) Gold skarns with substantial silver as by-product, represented by the Marvel Loch mine (production: 2,200,000 t at 3.5 g/t Au), and characterized by the mineral association pyrrhotite, loellingite, arsenopyrite, galena, gold and magnetite. (2) Gold skarns with low silver contents, represented by the Nevoria mine (production:1,850,000 t at 3.4 g/t Au), and characterized by the mineral association pyrrhotite, chalcopyrite, arsenopyrite, gold, Bi-tellurides and magnetite. (3) Copper-gold skarns, represented by the Elverdton mine (production: 850,000 t at .7 5 Cu, 0.81 g/t Au), and characterized by the mineral association magnetite, chalcopyrite, pyrrhotite, pyrite, gold and Ag-Bi tellurides.

Jan 1, 1990

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By D. G. Krige

Discussion by D.G. Krige I read the paper "The jackknife approach" with interest. There appears to be a widespread misunderstanding of the kriging variance as a measure of the error variance of the kriged grade estimate of an ore block. Virtually all mineral deposits display skew frequency distributions and are subject to the well-known proportional effect. Thus, it is usual to find in an ore body, when subdivided a really into subpopulations, that the variances of the grades (or the total sills of the variograms) for the subpopulations will be correlated with the corresponding mean grades (usually linearly with the squares of the mean grades). Thus, the variogram will be station. When this feature is evident, the relative variograms for the subpopulations (i.e., with variogram values divided by the relevant mean squared) will be similar, or they could even be accepted at an averaged model for the whole ore body with stationarity. Using this approach, the kriging variance will reflect the relative error variance that is to be multiplied by the kriged block grade estimate squared to yield the usual kriging variance for purposes of confidential limits. The objection that the kriging variance does not take into account the local grades used for a block valuation then falls away. In the example given by the authors, the global mean grade is not recorded. But the global variance, taken at the value of the total sill, is 0.005, whereas the variance of the 11 values used in the example is 0.000152. The two variances differ by a factor of nearly six. If the relative variogram approach is applicable in this case, the need for a jackknife technique will fall away. Also note that, for skew distributions, the confidence limits for ore-block estimates will be skew as well, and symmetrical normal limits will not apply. RepIy by G.S. Adisoma and M.G. Hester There are a few interesting ways to utilize the block-by-block kriging variance that the authors have encountered. One of them is to classify a particular block into a proven-probable reserve or a possible-resource category, using a somewhat subjectively determined kriging variance value. Here, the kriging variance still represents the drilling density, i.e., data configuration more than the data values. Professor Krige mentions another ingenious approach through the use of relative variograms. This will yield a block kriging variance that takes into account local (block) grade, as he correctly points out, for purposes of confidence limits. However, we are more interested in quantifying the uncertainties associated with grade estimation in a much larger scale than a block. e.g., for a mining phase or the minable reserve. The jackknife, through the block kriging shortcut, provides a simple solution to obtain a single estimation variance for a general shape. The authors' main reference discusses different ways to handle skewed distributions typical in mineral resource estimation, e.g., the weighted jackknife approach or data transformation. Also, as with any technique, we can always improve our estimate by subdividing into smaller populations that are geologically and statistically separate domains. As we have mentioned; the jackknife is but a tool in our collection of tools to solve estimation problems. The jackknife's appeals are its simplicity and versatility. It is handy when no other solution is available, or when the available solution is not practical. It is used with other methods, not to replace them altogether. ?

Jan 1, 1997

Liebherr Mining Equipment Co., of Newport News, VA and Baxter Springs, KS, introduced the T282, a new two-axle, diesel-electric, AC drive haul truck with a payload capacity of 327-t (360-st). The T282 was unveiled at a press briefing in October 1998 at the company's Baxter Springs research and development1 manufacturing facility. In addition to an increase in pay- load capacity, the truck's AC drive system has been de- signed to allow for easy configuration to a trolley-assist system with minimal additional equipment. The T282 provides fuel savings, reduced maintenance requirements, and reduced downtime and maintenance costs, providing the mine operator with increases in productivity. Basic dimensions and weight of the T282 are: ? Overall length, 14.5 m (47.5 ft). ? Overall width, 8.7 m (28.7 ft). ? Loading height, 6.5 m (21.2 ft). ? Height - body up, 13.9 m (45.9 ft). ? Empty vehicle weight, 201 t (221 st). ? Operating weight - loaded, 528.6 t (582.6 st). ?Engine, Detroit Diesel 16V4000 at 2 MW (2,750 hp). ?Electric drive system, Siemens/Liebherr.

Jan 1, 1999

By Downing Terry L.

Dry mineral beneficiation methods have been developed for separation of borate minerals from montmorillonite claystone gangue. The methods include the use of newly developed dry high intensity magnetic separators. The application of these methods has the potential for economic benefit at U.S. Borax Inc. in three areas: ? Processing surface impoundments (ponds) material. ? Pre concentrating ore to be fed to primary refinery. ? Concentrating borate minerals to produce potential products.

Jan 1, 1995

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27'6" diameter, 78'O" deep Brandywine Street - 30'6" diameter, 88.6' deep Ellicott Street - 33'0" diameter, 110'0" deep

Jan 1, 1985

By H. L. Hinds

Economic pressures to increase production to profitable levels reduced the Homestake's gravity recovery and overall recovery to un-acceptable levels. The operation of the Home-stake gravity gold circuit has increased gravity gold recovery to over 50%, improved overall recovery and increased mill availability for increased tonnage. The gravity circuit consists of three gravity gold recovery stages. The Circuit has four (4) duplex jigs, four (4) belt concentrating strakes and four (4) concentrating tables.

Jan 1, 1989

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022