Search Documents

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By Hans von Michaelis

The revolution in development of new technology and practices in the gold mining and metallurgy industry continues unabated despite the ups and downs in the gold price. Some of the new cutting edge technologies are listed in Table 1 overleaf. There is room to discuss just a few of these here, but many more are identified and described in RANDOL (1992). Cutting edge advancements in gold recuperation, can be sorted into three categories. The first category includes fundamental advances that offer major improvement with significant economic benefits. Second would include evolutionary developments that offer smaller, but nonetheless commercially valuable improvements. Finally there are those "advances" that are interesting but of trivial or question­able economic benefit to industry. It is essential to adopt a "systems approach" philosophy towards developing and applying new technology. Practical innovation often comes about as a result of having to solve a problem. Innovation for innovation sake is an ego trip. Environmental management has become an important part of the system and the environmental implications of new processes and practices in the mine and mill have to be carefully considered for potential benefits and/or liabilities.

Jan 1, 1993

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By Preusse. Axel

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By M. F. Bradley, G. M. Schoen

The Magmont Mine, a 50/50 venture between Cominco American Incorporated (the Operator) and Dresser Industries, Inc., (Halliburton), is a metallic mining and milling facility in the new lead belt of Missouri. The mine is located approximately 100 miles southwest of St. Louis. Legislation passed in 1992 by the Missouri legislature requires all metallic mining and processing facilities to apply for a Metallic Minerals Waste Management permit (MMWM) for their waste facilities. Regulations were subsequently promulgated by the Missouri Department of Natural Resources (DNR). Cominco obtained a MMWM permit (MM-006) from the Missouri DNR in 1992.

Jan 1, 2001

By William C. Larson

The number of uranium in situ leach operations has increased significantly since 1975. As of May, 1980, there were a total of 27 active projects, including 16 commercial scale operations (or under construction) and 11 pilot scale operations. The south Texas uranium district and Wyoming have been the most prominent areas in early field experiments as well as in commercial application of this new recovery technique, although in situ leach tests are now being conducted in Colorado and New Mexico. The growing number of commercial-scale operations is accepted as prima facie evidence that in situ mining now offers a third option along with open pit and underground mining for winning uranium from sandstone host rocks. It is estimated that in 1979 about 9 percent of the nation's total uranium production was from in situ mining. However in situ mining of uranium is not without its environmental controls. The primary emphasis of environmental controls falls into two catagories; namely, control of the leach solutions during mining and demonstration of ground water restoration. Finally this paper briefly reviews the Bureau of Mines research program in uranium in situ mining.

Jan 1, 1980

By J. K. Phiri

Copper mining is the main activity in Zambia and is confined to the large scale operations, mainly on the Copperbelt. The Copperbelt covers an area of size l00km by 50 km with a total of 10 underground and 5 open-pit mines operated by Zambia Consolidated Copper Mines (ZCCM) Limited. Most of the operations in these mines involves drilling and blasting. The loading of broken materials is by both manual and mechanical operations. Among the many risk factors associated with mining on the Copperbelt, is the occurrence of Pneumoconiosis which in the recent past has become quite prevalent and thus an important occupational health hazard for the industry. This study was carried out with the aim of establishing trends of pneumoconiosis incidence through the annual data collected by Pneumoconiosis Medical and Research Bureau of the Ministry of Health in Zambia, so that a basis could be formed for future research work. The study covers over 1,000 certified cases of Pneumoconiosis between 1960 and 1990

Jan 1, 1993

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic application, perlite properties of low density and fine particle size are desirable, while loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including particle size, density, and surface treatment are discussed in relation to the various insulation applications. Also, typical mineral processing and manufacturing techniques are reviewed.

Jan 1, 1987

By S. P. Banerjee

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1987

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By W. Petruk

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections in order to characterize a mill product and to determine the apparent mineral liberation. It was found that a representive polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly individual screened' fractions are not representative of the sample because minerals are partitioned during screening. Consequently the quantities of soft brittle minerals are increased in fine grained fractions and quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (1 Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analysing each fraction and combining the data. Somewhat less accurate data would be obtained by analysing a series of screened, fractions that have a wider size range of particles (5 Tyler size ranges). Mineral liberation analyses show that the most reliable apparent mineral liberation in each screened fraction is a value taken from a smooth curve drawn through the lowest points on a graph of % free vs size. A correlation between the apparent mineral liberation in screened fractions and calculated mineral liberations using Kings liberation model is good for sphalerite but not for chalcopyrite and galena.

Jan 1, 1985

By John Mitchell, Mark K. Jorgensen

Newmont Mining’s Ahafo Mine is located in Ghana approximately 300 km (190 miles) northwest of the capital city of Accra in the Brong-Ahafo region. The nearest city is Sunyani, located 45 km (28 miles) to the north. The Ahafo Mine will process ore from seven major pits that extend along a 40-km (25-mile) strike. Four pits are in the south and three pits are in the north. The resource is currently stated at 373 t (12 million oz). But it still has the potential for growth both from new discoveries and the development of underground operations.

Jan 1, 2007

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By J. Garretson

When mining accidents occur, workers often become trapped and/or incapacitated. Current rescue operations can be dangerous and too slow to produce favorable outcomes. Currently, no method exists for rescue crews to scout ahead at critical times to assess the situation. Sandia National Laboratories (SNL), through a National Institute for Occupational Safety and Health (NIOSH) sponsored program has developed the Gemini-Scout mine rescue platform. The Gemini-Scout was created to assist in underground mine rescue missions. It has been designed to go into potentially hazardous environments to assess the conditions (structural, air quality, temperature). In addition, it will enable two-way communications with potential survivors prior to human rescue teams being able to enter the area. The Gemini platform is a dual tracked-chassis design, which gives the robot excellent mobility in unstructured environments. The design includes a passive 2-degree of freedom joint between two identical bodies allowing for ±30deg of pitch and roll. In addition to the base mobility platform, the Gemini-Scout incorporates many other features to help it succeed in its underground mission. The electronics are mounted in explosion proof housings to ensure safe operations in hazardous gas environments. The platform is also able to operate in up to 18in of standing water with its elevated pan/tilt cameras for navigation. A four-channel video link and Two-way audio on the vehicle help to ensure located survivors can communicate with the robot operators. The platform also incorporates a Mine Safety and Health Administration (MSHA) approved multi-gas sensor to monitor air quality. SNL believes that this technology is broad enough to be appealing to other first responders, such as police, firefighters and medical personnel. Gemini could easily be fitted to handle earthquake and fire scenarios, and it could provide relief in currently inaccessible situations.

Jan 1, 2012

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining in usage in the mining industry. A variety of machines are now being used, including tunnel boring machines, roadheaders, continuous miners, surface miners and augers. These machines have advantages compared to drill-and-blast mining methods, including increased safety, lower cost, uniform muck size and accurately sized openings. A century of experience with mechanical methods has paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hard-rock mechanical mining machines. When several significant challenges have been met, mechanical miners will become integrated mining systems and will determine the design of mines.

Jan 1, 2002

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) multiple seam interaction between web and barrier pillars in superjacent mines, ii) subsidence and caving propagating to overlying seams and mines, iii) pooled water and the potential for inundation resulting from a breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, iv) the presence of overlying or underlying mine workings where pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist.

Jan 1, 2009