Search Documents

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By P. van der Veen

There are two key reasons for this presentation: - Sustainability - Improving the economic, environmental and social impact of mining. As I will discuss in my presentation we see sustainability throughout the mine life cycle as critical for successful mine development - that is the mine makes a successful contribution to economic development and poverty alleviation for the host community and host country and at the same time the mine is a successful investment for the investor. - Knowledge Sharing ? The World Bank is not only a development bank, but also a ?knowledge bank?. One of our key functions is the dissemination of usable information and knowledge. We are here not only to share our experience but to learn from your experience as well ? two reasons that fit clearly with the mandate of the World Bank Group.

Jan 1, 2003

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By B. D. Shah, H. S. Soto

Lack of selectivity in mixed mineral flocculation can be attributed to one or more of the following factors: dissolved ion interference, hetero- coagulation, mechanical entrapment in flocs, and entrainment of fines between flocs. In a study of the apatite-dolomite system, it was determined that dissolved ions do not have a significant effect on selectivity. Heterocoagulation was minimized by choosing proper process conditions and addition of a dispersant. Mechanical entrapment was proved to be insignificant and efforts were made to reduce entrainment by choosing an appropriate method of separation of flocs from fines. A new factor termed "polymer induced entrapment," which occurs due to limited affinity of the polymer to the mineral that is not flocculated, is postulated to be the cause for the loss of selectivity.

Jan 1, 1988

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By J. T. Bartlett

Life-of-mine process simulation is an interdisciplinary effort and a useful means of thoroughly evaluating mining and minerals projects. Communication between geologists, mine planners, miners, metallurgists, and managers not only benefits each discipline but facilitates design of an efficient operation and allows for accurate forecasting of productions and cash flow. By focusing on the key areas: geology; mine design; waste dumps; stockpiles; metallurgy; weather data; tailings disposal; using contours, block models, mine plans, process flowsheets, design criteria, operating and control strategies, maintenance schedules, and operating costs to perform detailed daily simulation from start-up to shut-down; a comprehensive understanding for all disciplines is achieved. Construction of a METSIM model that includes all test work and project data from drill holes through net present value calculations brings the pieces together to achieve optimum process design, minimize operating problems and eliminate the term ?black box? from project meetings and discussions.

Feb 27, 2013

By Markus Thewes, Mario Galli

"INTRODUCTIONProject-related studies showed that lab tests are a helpful tool for the planning of EPB tunneling and soil conditioning in cohesionless soils. This type of ground commonly represents the extended application range for EPB shields, which demands for a treatment with additives. Considering soil conditioning with foam, so far, approaches exist for the investigation of the foam quality and of the conditioning behavior of soils (e.g. (EFNARC GUIDELINES 2001 2003)), but not any standards for testing procedures related to soil conditioning. State-of-the-art research on the topic is and was conducted for example in Bochum (Germany) cf. (Budach 2012; Maidl 1995), in Lyon (France) cf. (Quebaud et al. 1998), in Oxford and Cambridge (Great Britain) cf. (Borghi 2006; Peña Duarte 2007), in Delft (Netherlands) cf. (Bezuijen and Schaminée 2001), in Turin (Italy) cf. (Borio 2010; Peila et al. 2013; Vinai 2006), and in Aachen (Germany) cf. (Vennekötter 2012). Additionally, applied science is reported by the tunneling practice and suppliers of conditioning agents. Although the research focus in all these and further studies varied, similar test methods and test series were applied. A standardization of essential properties and testing methods (setup and procedures) however did not take place. The results from laboratory testing can only function as index values for practice because in the studies, production and application of the conditioning agents mainly takes place under atmospheric conditions. Nevertheless, the tests enable basic understanding of feasibility as well as processes and interactions going on during soil conditioning. For recommendations for standardized and reproducible testing see (Budach 2012; Budach and Thewes 2015).The most extensive investigations on the flow behavior of soil-foam mixtures have been performed by using the slump test from concrete engineering, cf. (DIN EN 12350-2 2009-08), which originally is applied on evaluating the workability of fresh concrete. Although this test does not describe the actual flow behavior, it rather represents an index on the workability, very much experience exists with this test method. Besides others, the workability – or flow behavior – of the EPB support medium certainly is a major factor of influence on the properties of the material in the excavation chamber and thus, for effective tunneling with EPB shields, cf. (Galli and Thewes 2014). For a summary of various investigations on the workability of conditioned soils using the slump test and resulting recommended slump ranges see (Budach 2012; Vinai 2006). Thereof, slumps between 10 and 20 cm have been reported as suitable workability for EPB applications. However, there is actually not much known about the real flow behavior of soil-foam mixtures related to rheological properties such as the viscosity (?) or potential yield stresses (t0). These physical values are necessary for a realistic determination of face pressure, for the design of required torques, and for an evaluation of the material flow at different locations in the excavation chamber, in the screw conveyor or on the conveyor belt. To generate a linear pressure distribution at the tunnel face, as it is assumed a priori, a low-viscosity fluid is favorable, whereas in the screw conveyor, a high-viscous fluid is needed for a controlled pressure decrease. On the conveyor belt, yield stress plays an important role preventing deliquescence and spilling from the belt. Attempts in characterizing the actual flowing of soil-foam mixtures have so far only been made by few researchers, the application of rheometry is rare."

Jan 1, 2016

By Howard G. Coopersmith

Kelsey Lake kimberlites are a cluster of eight diamondiferous pipes that occur in the northern State Line kimber lite district of the Colorado-Wyo¬ming diamond province (Coopersmith 1991, 1993) (Fig. 1). This is located at the southern margin of the Wyoming Archean province. Two relatively large pipes and a few smaller bodies define the cluster (Fig. 2). The Kelsey Lake kimberlite cluster has been developed as the first diamond mine in the United States. The cluster was discovered in 1987. Full-scale production began in the spring of 1996. Mining has produced gem-quality diamonds up to 28.3 carats in size. The 30 State Line kimberlites, intruded about 390 million years ago into Proterozoic crystalline rocks, were presumed to be underlain by Archean basement of the Wyoming Province. Nearly all the kimberlite pipes contain diamond but only the Kelsey Lake pipes are economic. The Kelsey Lake kimberlites contain predominately diatreme facies kimberlite, with minor hypabyssal and crater facies rocks locally occurring. Alteration and weathering of the kimberlites is extensive. Petrologic studies indicated an underlying lithosphere that has a largely Proterozoic signature and shows evidence of deep melt and metasomatic events. Current development has concentrated on the two largest pipes. These have been bulk-sampled after geological study (1987) identified the presence of small diamonds and mineral chemistry indicating favorable diamond conditions. A 10-t/hr (11-stph) rotary pan plant was established in 1992 to process thousands of tons of bulk-sample material. Grades and gem-quality diamonds to 14.2 carats in size were recovered. Early in 1995, it was decided to move from evaluation to commercial mining. Production began in early 1996. A 195-t/hr (215-stph) rotary pan plant was built. A water supply system and tailings disposal have also been incorporated. The project straddles the Colorado/Wyoming border. Existing mining permits were amended to incorporate the increased scale and new plant facility. The permits for this project included the following: Colorado mining permit, Wyoming dozing permit, Corps of Engineers Section 404, Colorado NPDES, Wyoming NPDES, Storm water Management Plan, Air Pollution Emission Notice, various Colorado and Wyoming State Engineer and well permits, Substitute Water Sup¬ply Plan, Larimer County Special Use Review, and US Forest Service road use permits. The temporary destruction of a wetlands area was a sensitive issue. It has been addressed through the Clean Water Act Section 404 permit administered by the US Corps of Engineers. This use will be mitigated by creating new, self-sustaining wetlands in the immediate drainage system. A comprehensive and bonded reclamation plan is incorporated in the permits. Diamond mining and ore processing is environmentally benign. No chemicals are used in processing the diamonds. The plant is a water wash facility. The kimberlite ore is inert, as is the granite wall rock. The exposure of the ore body and the subsequent ore processing and waste rock and tailings containments pose no threat of release, leaching or dispersion of any detrimental elements. There is no acid-forming waste. Even a prolonged acid rain environment will not produce a harmful leachate. Slimes containment and clarification ponds will prevent unacceptable levels of suspended solids in water discharge. The isolated, restricted access and nonvisible nature of the mine and processing has led to straightforward permitting. Geology The State Line district is located in the northern

Jan 1, 1997

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988

By F. -U. Schneider, F. Wellenkamp

Based on previous investigations of ultrafine comminution in planetary ball mills, a new centrifugal mill has been developed which permits similar high stress conditions. Because this new type of mill is equipped with an immobile chamber, devices for measuring energy, for cooling the milling vessel, as well as, in continuous operation, for material feed and discharge can be more easily attached than to planetary ball mills. Observations of particle behaviour have shown that, in the case of dry grinding, most of the material is found on the mill walls even after short grinding times. Due to the fact that energy dissipation takes place mainly in the zone near the wall, a grinding system which reduces the amount of ball filling required is at an advantage.

Jan 1, 1995

By Walter Steiner, Claus Becker

INTRODUCTION General Switzerland is a densely populated country in the heart of Europe. With its total surface of 41.300 km2 and a population of 6,8 million in 1986 the average population density is 163 capita / km2. The population density is lower than in Germany (245 capita/ km2) or the Netherlands (355 capita/km2). The USA have a population density of 26 capita/ km 2. However, sixty percent of the Swiss surface is covered by the Alps and another ten percent by the Jura mountains the remaining thirty percent of the surface is covered by the Swiss plateau where the majority of the population lives. The population in the inhabitated areas is thus substantially higher and may possibly reach those in major metropolitain areas. Due to the high population density in Europe in general and Switzerland in particular future traffic demands cannot be fulfilled sole by car or plane. Environmental and land-use constraints lead to the third option for growing transportation needs: High-speed rail (Bovy, 1990). Switzerland has developed its own approach to promote public transportation and in particular rail transportation: "Rail 2000" (Stalder, 1990). The system "Rail 2000" is based on a series of hubs distributed over Switzerland where easy connections can be made.

Jan 1, 1991