Search Documents

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By T. V. Subrahmanyam

Unlike coarse particles (40-50 µm), the fines (<10 µm) have low collision efficiencies with gas bubbles in flotation process. Among the alternative methods for recovering the fines are their aggregation with coarse particles (carrier flotation) and flocculation of the fines alone (shear-flocculation), prior to flotation. In any case, hydrophobic aggregation is the mechanism involved though the technique is known by different names in literature. This paper deals with theory and state-of-the-art of particle aggregation. To illustrate the dependence of aggregation on particle hydrophobicity, charge and, in turn, the sheer force, the results of quartz-DDACI and galena-xanthate systems are considered. In the flotation of complex ores selectivity is achieved by chemical control and aggregation of particles of the same species is analogous to that; however, more work is necessary on ores for a better understanding of the pulp chemical aspects from the view point of selectivity in aggregation. For a few ores, the results of earlier workers confirm improved recoveries of fines by aggregation prior to flotation.

Jan 1, 1997

By Keith Whiting

The Little Boulder Creek molybdenum deposit is in central Idaho, in the White Cloud Range about 3.2 km (2 miles) northeast of Castle Peak, the highest peak in the range. The elevation of the deposit is about 2591 m (8500 ft). The deposit is accessible only by helicopter or by a 12.9-km (8-mile) trail from the county road along the East Fork of the Salmon River. The nearest towns are Clayton [25.7 km (16 miles) northeast], Stanley [33.8 km (21 miles) northwest], and Ketchum [45 km (28 miles) south-southeast]. The principal known deposit at Little Boulder Creek is called the "North Zone." In this zone, the molybdenite occurs both in stock- work veinlets and disseminated through metamorphosed quartzite of Pennsylvanian age. Pyrite is ubiquitous, averaging perhaps 0.05%. Scheelite and/or powellite are present in trace amounts. An intrusive quartz monzonite stock, probably of Cretaceous age, bounds the deposit on the west. A steep fault which drops Tertiary age Challis volcanics into contact with the mineralization limits the deposit on the east.

Jan 1, 1991

By E. Spyridonos

Sustainable development in the mineral industry requires a paradigm shift from purely economic to multi-objective decision-making, considering economic, social, environmental and governance criteria. The commonly accepted aim is responsible stewardship of non-renewable resources. State-of-the-art 3D geological and mine modeling software technology can contribute to meet this objective as reliable and accurate geological models form the basis for an optimum management. The benefits obtained by the application of computerized modeling are illustrated at hand of three studies. The examples cover global and local producers of industrial minerals in fully developed as well as development countries. They refer to different levels of planning, from initial resource assessment over long-term planning to the generation of rolling forecast for operative planning in a running mine.

Jan 1, 2003

By John E. Butler

Due to the present economic climate, particularly the depressed copper market, conventional mining, milling and flotation operations have been suspended. However, due to the apparent amenability of the ore to &apos;natural&apos; leaching, investigations have been initiated into establishing an in-situ leaching operation as a preferred alternative to conventional operations. Cement copper production has been developed in parallel with the leaching trials and is presently at the rate of approximately 3,000 tonnes of contained copper per annum. Testwork includes controlled leaching of ore both in the laboratory and in-situ following blasting.

Jan 1, 1981

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By Max John

INTRODUCTION One of the main advantages of the New Austrian Tunneling Method (NATM) is its adaptability to varying rock conditions. This method is therefore successfully applied when complex geologic features are expected which cause uncertainties in the prognosis of the rock mass behaviour, as was the care at the Arlberg Expressway Tunnel. Furthermore, by employing the NATM problems are avoided when encountering varying geologic conditions or even extension fault zones along the tunnel, as was the case at the Dalaaser Tunnel and Perjen Tunnel. The NATM can also be used for rock and soil. The following examples will show how various rock conditions can be mastered. In accordance with the NATM all tunnels which will be discussed are road tunnels having a cross section area between 70 and 100 m2. The construction consists of a primary support, which ensures stress redistribution during excavation (Figure 1). The primary support is reinforced shotcrete strengthened by steel arches, when necessary, and rock bolts. When encountering rock pressure, swelling rock or soil, the primary support is suplemented by an invert arch. The purpose of the secondary lining is to increase the safety of the tunnel with regard to long-term stress redistribution processes or changes in rock mass properties as well as to protect the insulation. The secondary lining consists of cast concrete without reinforcement and is generally 0.25 or 0.30 m thick.

Jan 1, 1981

By Bernard L. Cohen

I.INTRODUCTION The B E I R-III Report (NAS-1980) introduces large increases in the estimated health effects of radon as compared with previous work (NAS-1972). It is the purpose of this paper to point out some important failures of these new BEIR-III estimates, to offer a general critique of the procedures used in obtaining them, and to offer more rational estimates. In Sec. II we use the BEIR-III model to calculate the risk to non-smokers from environmental radon, and show that it predicts more than twice the total lung cancer rate actually experienced by nonsmokers. In Sec. III we review the histological evidence which shows that no more than about 10% of the lung cancers among non-smokers can be due to radiation. In Sec. IV, we discuss alternative causes of lung cancer, which further reduces the fraction that can be caused by radiation, and in Sec. V we summarize and conclude that the BEIR-III model over-estimates the lung cancer rate in nonsmokers due to environmental radon by at least a factor of 40. In Sec. VT we review the evidence on risk of radon exposure to smokers, and conclude that it is probably not more than four times the risk to non-smokers; this means that the BEIR-III model over-estimates the risk of low level radon exposure to smokers by at least a factor of 10. In Sec. VII, we consider the reasons for the large over-estimates in the BEIR-III. Report. II. BEIR-III LUNG CANCER RATES DUE TO ENVIRONMENTAL RADON AND COMPARISON WITH TOTAL LUNG CANCER RATES AMONG NON-SMOKERS The BEIR-III Report gives the following estimates of the lung cancer risk from low-level radon exposure in terms of working-level-months (WLM): age 35-49, risk = 10 x 10-6 /yr-WLM 50-64, 20 >65, 50 where ages refer to age at death. For latent periods between exposure and onset of these risks it gives age 0-14, latent period = 25 years 15-34, 15-20 years (we use 17 yr) >35, 10 years where ages refer to age at exposure. This is a clear and unambiguous model which is readily usable for deriving numerical estimates. We begin by using it to calculate lung cancer rates due to environmental radon. *This is an abridged version of a paper scheduled to appear shortly in Health Physics. The first step in this process is to estimate the environmental exposures; this was done in a recent paper (Cohen-1981) which concluded that these are about 0.22 WLM/year. In Table 1, this is used to calculate the BEIR-111 predictions for radoninduced lung cancer rates in the U.S. (Col. (5)), and by combining these with population statistics, it is shown (Col.(7)), that it predicts about 24,500 fatalities per year, almost one-third of all U.S. lung cancers. The comparison between the age-specific expected rates from Col. (5) of Table 1 and observed rates among non-smokers is shown in Table 2. The recent paper by Garfinkel (1980) presents the results of a 12 year follow-up on one million Americans in a study by the American Cancer Society. The paper by Hammond (1966) gave the results of the first four years of that study. The paper by Kahn (1966) is based on the so-called "Dorn Study" of 293,000 U.S. veterans of World War II who carry government health insurance. It represents 8 and 1/2 years of follow-up. A recent update on that study (Rogot-1980) does not give absolute lung cancer rates, but the age-standardized ratio between smokers and non-smokers has remained the same which indicates that there has probably not been an important change in the rates for either. The paper by Hammond and Horn (Ha-1958) was an early study by American Cancer Society. It is immediately evident from Table 2 that the BEIR-III estimates for lung cancer induced by environmental radon exceed the [total] lung cancer rates due to [all] causes among non-smokers by about a factor of two at every age. It is only fair to point out that this does not represent a direct discrepancy with the BEIR-III Report since the latter states that its estimates for non-smokers may be too high by a factor ranging from 1 to 6, favoring a factor intermediate between these. Comparisons can also be made with total lung cancer incidence for all ages. A paper by Hammond and Seidman (Hammond-1980) gives the rate for ages above 40 to be 177 x 10-6/year for men and 124 x 10-6/year for women, whereas the rate calculated in Table 1 from BEIR-III for ages above 40 is 309 x 10-6, a factor of two higher. For all ages, the rate among women was reported as 36 x 10-6/year (Hammond 1958) as compared with 114 x 10-6/year calculated from BEIR-III in Table 1, a discrepancy of well over a factor of two. All of the data we have presented are basically from three study groups, but in all three cases the BEIR-III estimates for lung cancer induced [by environmental radon alone] are a factor of two higher than actual [tota] lung cancer rates among non-smokers. Another approach to comparing the BEIR-III pre-

Jan 1, 1981

By AKIHIRO YOSHIMURA, HIDEKAZU KATO, KOTA TAKATORI, YASUNARI MATSUNO

Chalcopyrite (CuFeS2) is the most refractory copper mineral when treated in conventional sulfate media leaching systems. This study is the first to examine the use of a dimethyl sulfoxide (CH3SOCH3), or DMSO, solution containing copper chloride (CuCl2) in the leaching of chalcopyrite. The DMSO solution containing CuCl2 could selectively dissolve the valuable metals of copper (Cu) and gold (Au) from chalcopyrite while leaving minerals with little economic value, such as pyrite (FeS2), and the penalty element arsenic (As) in the residues. Leaching chalcopyrite using a DMSO solution that contains CuCl2 offers a number of advantages, including eco-friendliness and easy operation.

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By Jianguo Hao, Qingbiao Zhao, Bingnan Hu, Shimin Fan

The paper makes a systematic analysis of interaction between backfill and pillar in coal mining. It compares the difference of pillar strength with backfill and without backfill. It is proved that there are the obvious improvements in pillar strength and the decrease in subsidence. It discusses the subsidence effects of different extraction ratio, different backfill ratio, and different elastic modulus ratio in details. The paper analyses the sensitivity by orthogonal test method. At last, author proposes some suggestion to increase pillar strength, to reduce subsidence, and to guide engineering practices.

Jan 1, 2001

By G. Hwang, S. Park, H. Kim, J. Choi, P. Seo

"In the mineral processing, clay minerals have negative effects on the flotation of valuable minerals. In this study, we investigated how the floatability of malachite (CuCO3·Cu(OH)2) is affected by presence of the clay minerals in the fundamental aspects. Flotation experiments were conducted by using Na2S and PAX (potassium amyl xanthate), and the floatability of malachite was compared between the cases in the presence and absence of clay minerals. The results showed that floatability was greater in the absence of clay minerals than in the presence of clay minerals and decreased with increasing weight percent of kaolinite under same conditions applied. In addition to examine how clay minerals affect malachite floatability, we conducted flotation experiment with changing clay adding order. The results indeed showed that malachite floatability was affected by clay adding sequence. INTRODUCTION The demand of copper is growing as industrial development increases, but mineral resources are limited. Therefore, studies for Cu oxide flotation are being conducted to improve their recovery(1-3). However the mining industry is well aware of the difficulty in treating copper ores in the presence of clay minerals(4). Clay minerals have unique properties and these properties may affect flotation. In the previous studies, the effect of slime coating of clay minerals on flotation was investigated(4-6). For example, Zhao and Peng (2014), Peng and Zhao (2015), and Arnold and Aplan (1986) found that clay slime coating on chalcopyrite, chalcocite and coal surfaces through the electrostatic attraction reduced surface hydrophobicity and then depressed the flotation. Other researchers have also reported clay minerals have impact on pulp rheology. Especially in the case of bentonite, pulp viscosity increased with increasing amount of bentonite and the higher pulp viscosity have deleterious effect on copper recovery(7, 8). However, these studies only focus on slime coatings and pulp rheological behavior. Forbes et al. attempted to decoupling rheology and slime coatings effect on flotation but this study has limitation that individual role of two clay species either attached to mineral or suspended in bulk solution was excluded(9). Hence, in this study, we aimed to investigating the effects of individual clay (suspended and attached) on malachite flotation."

Jan 1, 2016

By Thomas H. Holley

This presentation will describe the underground excavation at the Bad Creek Pump Storage project. It consists of approximately 3,650 m of various size tunnels ranging from 4.2 m to 9.0 m finished diameter, a powerhouse cavern 45 m high by 135 m long by 22.5 m wide, and 422 m of 9 m diameter shaft. A total of 350,000 m of rock will be excavated, hauled, and placed in a submerged wier. Temporary rock support consisting of shotcrete and/or rockbolts is installed as required.

Jan 1, 1987

It is widely accepted that particles stabilize flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Furthermore, there is currently no technique that allows the prediction of the effect of different flotation reagents on froth stability, without carrying out froth stability experiments.

By Wayde Esplin

At the Barrick Goldstrike processing facilities in northeastern Nevada, sulfide ore is pressure-oxidized at a temperature of 440° F and 420 p.s.i. in six autoclave circuits. The low pH, high temperature, and abrasive characteristics of the oxidized slurry present many new and unique maintenance challenges. To meet these challenges, the Barrick Goldstrike autoclave department formed a reliability group in August 1998. One of this group's critical missions is to reduce both maintenance costs and unscheduled downtime through the application of predictive maintenance technologies and Reliability Centered Maintenance Analysis. This paper discusses some of the successes of the reliability program at the Barrick Goldstrike autoclave.

Jan 1, 2000

By Lane White

In conjunction with its 1993 Annual Meeting, held Feb. 15-18 in Reno, NV, SME sponsored a symposium, "Conveyor Belt Engineering for the Coal and Mineral Mining Industries." Eighteen papers were presented, grouped into four sessions: Low Tension Drives, High Tension Drives. Novel Techniques and Specifications. Three of the papers have been republished in this issue of MINING ENGINEERING. Brief summaries of the other 15 papers are presented here. (The 193-page symposium Proceedings, edited by Mike Evans of Consol, includes all of these 18 papers and is available from SME. For the convience of interested readers, an order form is included at the end of this Proceedings summary.)

Jan 1, 1993

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

By J. F. Archibald

It is often alleged by mine ventilation engineers that no reliable method exists to forecast the levels of radiation to be encountered in future uranium mines. It results that the design of uranium mine ventilation systems is based on factors other than radiological hazards, such as radon and radon daughter concentrations, for which permissible limits are set. Ventilation has been used to date as the main control mechanism for radon and radon daughters. Although it has become increasingly difficult to provide enough ventilating air to reduce the radon gas and its daughter products to safe levels in some mining arrangements, it is not the object of this paper to discuss alternatives to ventilation. This paper will describe a methodology followed by the authors over the years to estimate the levels of radiation to be encountered in underground and open pit uranium mines. Ventilating air is used to maintain working level concentrations within safe limits. The sources of radon and radon daughters and the quantities of each which will be produced, will be of great value in planning and designing a ventilation system to control them. This information can afterwards be integrated into the overall mine design. The methodology to be outlined can also be used to estimate, given a mine design format, the radiation levels to be encountered. If levels are not acceptable, modifications in the mine design can be made at an early stage. The emphasis is placed on an integrated effort where the ventilation engineers and the mine design engineers work in close collaboration from the very start of the mining project. Estimation of radon and radon daughter levels can be initiated as soon as core samples are obtained from the exploration programmes.

Jan 1, 1980

By D. R. Baughman

Copper oxide deposits that may be considered for in situ leaching exist in unique geologic settings, different from uranium deposits. A large number of interrelated factors must be considered in wellfield design. Many of these factors are hard to quantify and are directly related to geologic features of the orebody. This paper discusses some of the important factors in wellfield design and suggests an outline for a design procedure.

Jan 1, 1988