Search Documents

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By Stephen C. Tadolini, Thomas M. Barczak

Western mines have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the early 1990’s provided a very effective alternative and remains the dominant form of tailgate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled together, provides more capacity than an equivalent sized Can support and improves transport efficiency. However, the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but they have not been proven in high deformation environments. Alternative supports are also being used in longwall recovery operations. These include the Rocprop and Omni Prop, which are extendable support systems. They also provide active roof loading which can be beneficial in these applications. Specialty supports, such as the Sand Prop and Spider Prop, have also been introduced into western longwall operations. This paper compares the performance characteristics of these various support systems.

Jan 1, 2005

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By Barry A. Hillman

Respirable (PM-10) crystalline silica is regulated by the State of California as a carcinogen. The risk-management of this material by the State exemplifies the inherent problems in the development of regulations based on current risk-assessment practices. The influence of extremely conservative risk-assessment and risk-management can be expressed in economic impacts including the increased cost of production, reduced competition, increased prices, reduced employment and redistribution of income. This paper attempts to contrast theoretical risk- assessment and risk-management with current application using crystalline silica as an example. Based on health information pertaining to silica, the paper examines federal and State of California regulatory and public policy positions. Using current risk factors and empirical data for the Central Valley of California, the projected incidence of lung cancer in humans is examined. While such an analysis would project an extremely high incidence of lung cancer as well as silicosis, not a single case of either lung impairment has been recorded within the study area or throughout the world in the general population. This suggests that sound guidelines for the analysis of scientific information have given way to the assumption that virtually any information representing a substance as a carcinogen is to be considered valid with little or no qualification.

Jan 1, 1992

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1975

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By Gary Jackson

Preliminary engineering for the Waller Creek Tunnel was completed in 2001, but the project was held in abeyance until the summer of 2007. This paper describes several features of the revised design, which required significant changes from the original concept. Most notable is the expected replacement of a tunnel boring machine (TBM) by conventional tunneling. The considerable influence of geological conditions on the tunnel vertical alignment is discussed, in particular the impact of the zones of Eagle Ford Shale with swelling potential. Other features which are described include the wide span tunnels and large diameter shaft requirements.

By E. Simoncini, S. Ulgiati, M. Raugei

A thorough Life Cycle Assessment of ilmenite extraction and processing to yield synthetic rutile (ERMS/EARS process) was performed according to ISO norms 14040 and updates. The LCA includes the parallel application of selected environmental impact assessment methods (as illustrated in Ulgiati et al. [1]), the results of which are compared and discussed. A MI value of 16 kg of abiotic matter per kg of output rutile is calculated, which is largely determined by the amount of coal that is employed in the reduction and drying steps. The Gross Energy Requirement is 3.33 * 107 MJ/kg, a value which we found to be comparable with that previously calculated by us for alumina. Finally, the increase factor of the Emergy Intensity from the raw mineral to the marketed rutile is 3.19, which points to a comparatively medium-low requirement for indirect environmental support. GWP and AP were calculated to be respectively 1.89 kg(CO2eq)/kg and 12.7 g(SO2eq)/kg.

Jan 1, 2005

By Thomas P. Kwiatkowski, Len Cobb, Christopher D. Orlandi, Judith H. Jones

The Inland System supplies raw water to the industrial and domestic users in the City of Birmingham, Alabama. The Inland System, which is nearly 60 years old, consists of an approximately 57.9m (190 feet) high earthen dam across the Blackburn Fork of the Black Warrior River, a 39.6m (130 feet) high reinforced concrete intake structure, a 1524mm (60inch) diameter Dresser coupled steel transmission pipeline, and various distribution lines extending into Birmingham. The Inland System was owned, operated and maintained by the Industrial Water Board (IWB) of the City of Birmingham, an agency of the city government, from 1958 until 1994. In 1994, the City of Birmingham consolidated all water and distribution functions under the Birmingham Water Works Board (BWWB). In 1988, the IWB determined that the Inland System had reached a point where its reliability could not be assured without an in-depth evaluation and renovation. The IWB engaged Christy/Cobb, Inc. (CCI) of Birmingham as its consultant for the renovation work. CCI evaluated the Inland System and submitted a report to the IWB in April, 1992. The report contained several recommendations for capital improvements to the system including increasing the emergency spillway capacity, reconstructing the fuse plug, relocating public access to the lake away from the dam area, constructing a new intake structure, and constructing a tunnel through the dam abutment to deliver the water from the proposed intake structure to the existing 1524mm (60 inch) diameter supply line. The new intake structure and tunnel would provide for a future maximum demand flow rate as well as provide bypass and level control capabilities. CCI was authorized in 1992 to proceed with the engineering design for the renovation of the Inland System with emphasis on the spillway and intake structure. PROJECT DESCRIPTION The major component of the renovation of the Inland System was the new intake structure and tunnel through the dam abutment. CCI engaged Jenny Engineering Corporation (JEC) of Springfield, New Jersey as a consultant for the tunnel design. JEC was responsible for the design of the tunnel, the connecting shaft between the intake structure and tunnel, and the steel pipe final lining, while CCI was responsible for the intake structure and the connection to the existing supply pipeline as well as overall project management. CCI and JEC evaluated the project site in order to select the location for the new intake structure and set the alignment for the tunnel. A factor in the evaluation process was that the level of the lake could not be lowered to construct the new intake structure since the supply of water from the Inland System had to maintained. Therefore, a location was required which was

Jan 1, 1997

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By Stanley M. Miller

Analysis of discontinuous rock masses for engineering design purposes requires information about fracture characteristics. For such studies, fractures or other elements of the rock fabric (bedding, foliation, etc.) should be considered in a statistical manner because they generally have high frequencies of occurrence and are discontinuous over the design area. A practical design procedure includes defining structural domains as those areas which contain fractures with similar orientation patterns. Within a structural domain, the statistical distributions of fracture set characteristics (spacing, fracture density, dip, dip direction, etc.) may be computed from mapped data and then used to quantitatively describe the rock fabric. These distributions can then be randomly sampled (using Monte Carlo techniques) to simulate the rock fabric and to help define potential failure surfaces along fractures. 1 The prediction of failure geometries is an essential part of stability analyses used in designing rock slopes or underground openings. In current probabilistic design procedures, Monte Carlo techniques that rely upon the iterative generation and analysis of deterministic instability models do not incorporate spatial aspects of the random variation in fracture set characteristics, 1,2 but consider the characteristics to be spatially independent.

Jan 1, 1979

By R. J. Kline

Most accidents are the result of risk taking. They can happen anywhere. Our coal industry categorizes accidents by type, occupation, commodity, age, every way you can imagine. We now know, how many were injured and when, for all the different types of accidents. We have ask ourselves many times, why are we having accidents, how can we stop the accidents and fatals in our industry? Present numbers and projections do not show that this will happen. Serious accidents can result in fatalities. Fatal accident can be prevented, and the coal industry can achieve zero fatalities. How soon this happens, depends on a great number of factors. I will discuss accidents and reasons for us having accidents in an attempt to get to the root causes. The historical perspective will be touched on, and the risk and analysis of accidents will be probed.

Jan 1, 2000

By Bryan Ulrich

Rroundtable 2009, a Knight Piésold and Co.-hosted roundtable discussion on mine closure and cover design was held at the Red Lion Inn and Casino in Elko, NV on Feb. 12, 2009. Knight Piésold?s Bryan Ulrich and Steve Boyce, as well as Knight Piésold representatives Cynthia Parnow and Corey Conrad from Denver, CO, and Rick Frechette from the Tucson, AZ office were on hand to help facilitate the discussion. The meeting played host to approximately three-dozen attendees from four states. Attendees included personnel from seven mining properties and attendees from corporate offices. The majority of attendees were people directly involved with environmental work on a day-to-day basis. Other attendees were project managers whose jobs involve some level of environmental focus. The purpose of Roundtable 2009 was to exchange ideas and information pertaining to mine closure and cover design associated with almost any aspect of a mining operation. This type of forum provides a less inhibited format for discussion, when compared with traditional conferences and symposia. In the roundtable format, lively discussions are encouraged. This discussion was the fourth in the series of Elko Roundtable events. Previous roundtables pertained to heap leach pad design, construction and operation; design, construction and operation of tailings storage facilities and site-wide water considerations. The initial subtopics for Roundtable 2009 included:

Jan 1, 2009

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

Laboratory techniques have been developed at the Julius Kruttschnitt Mineral Research Centre which relate comminution energy to size reduction. These relationships have been applied in the mathematical modelling of autogenous and semi-autogenous mills. Since their development in 1987 these models have been successfully used in many wide ranging design and optimization studies. A description of the basic structure of the models is presented with particular reference to ore characterization. Two case studies are presented which illustrate their effectiveness in evaluating and predicting the effects of circuit changes.

Jan 1, 1992

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024

By G. Brooks, J. T. Ellington, M. Yensco, G. E. Mcquien, M. T. Ityokumbul

Coarse silica flotation from intermediate pebble (IP) product has been carried out a pilot plant Dual Extraction Column (DEC) at an operational phosphate mine in Central Florida. The solids feed rate ranged from 4.16 – 5.3 TPH while the amine dosages ranged from 0.32 – 0.93 lb/T. The optimum amine dosage when using recycled process water was deter-mined to be 0.6 lb/T. With a feed containing 40-45 BPL and 38-45% insol, the results show that the IP can be upgraded to 56-61 BPL and insol of 16-22% at 85-90% BPL recovery. The results show that the DEC is an effective device for flotation of coarse silica from the IP. The advantages of upgrading the IP prior blending with the pebble are presented and discussed.

Jan 1, 2004

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008