Search Documents

By J. J. McDougall

The Windy Craggy copper-cobalt-bearing massive sulfide lies in the Tatshenshini map area of northwestern British Columbia, where British Columbia joins Alaska and the Yukon. The area is covered with numerous glaciers and ice fields that mask geologic detail and hamper ground access. In 1957, Ventures Ltd., the predecessor of Falconbridge Ltd., undertook a reconnaissance of the area using a float-equipped Supercub. At that time, large lakes and glaciers were unnamed and little was known of the geology. The prospecting team was led by J.J. McDougall with Stan Bridcut as pilot-prospector. Prospecting was directed at the St. Elias Mountains between the rich Kennecott copper deposits to the northwest and the Maid of Erin silver-copper mine on the Haines Road, BC. Reconnaissance flying in 1957 and early 1958 eliminated vast segments of the Kennecott-Haines Road terrain as being too inaccessible for mining. In 1958, the Supercub landed at an unnamed lake and the terminal moraine of an unnamed 12.9-km (8-mile) long glacier was prospected. The lake was called Tats Lake and the glacier named Tats glacier (short for Tatshenshini). Float of sulfide was found in the moraine. Follow-up investigation along Tats glacier led to the discovery of several small sulfide deposits and these were staked. Prospecting active glaciers in this area can be complicated because of drainage capture by eroding valley glaciers. Glacier capture resulted in the float from one mineralized area being deposited at different times in three widely separated moraines. Float of the Windy Craggy deposit, therefore, occurs along the course of older glaciers and at the base of the currently active ones. The problem of sourcing caused much additional Supercub reconnaissance. It is interesting to note that about 40 geographic names were given various features in this unmapped portion of the St. Elias Range, and these names were ultimately officially adopted.

Jan 1, 1991

By Corale L. Brierley

The effect of hydrogen peroxide (H2O2) on growth and respiration of Thiobacillus, thiooxidans, and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uranium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were inhibited after contact with 0.82 mM H2O2. Inhibition of oxygen uptake by T. ferrooxidans occurred at 8.24 mM H2O2, and growth was inhibited after 6 hours exposure to 2.06 mM H2O2. Higher concentrations of H2O2 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface. INTRODUCTION In recent years, hydrometallurgical processes for recovery of metal values from low-grade ore minerals have played an increasingly important role. Dump leaching of low-grade copper waste materials in the western United States now yields 11.5% of the total U. S. copper production. Although scavenger operations in uranium leaching have been successful, the state-of-the-art of in-situ

Jan 1, 1977

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

Jan 1, 2003

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By John L. Watson, Suren Mishra

Many of the wastes produced by modern steel plants are pulps or sludges containing significant concentrations of iron and displaying some ferromagnetic characteristics. These waste materials are often suited to treatment by magnetic cycloning to produce a high solids content underflow and a clean water overflow. Alternatively in the classification mode, the magnetic cyclone can produce a high iron underflow product for recycling by discarding fine non-magnetic material to the overflow. Results for the treatment of a variety of steel plant wastes in 5.0cm, 2.5cm and 1.25cm diameter cyclones, operating with and without an applied magnetic field, are presented. It is demonstrated that the magnetic cyclone increases solids recovery to the underflow product, especially at finer particle sizes and for higher solids content feed pulps.

Jan 1, 1992

By T. W. H. Parker, S. B. Sadleir

ABSTRACT A comprehensive program of air flush core and reverse circulation drilling, trial mining and beneficiation test work was carried out in 1980-1982 to re-assess the potential of the Mitchell Plateau bauxite deposit. The results generally confirm previous work by Amax Corporation. The bauxite is a medium available alumina and reactive silica deposit which responds well to wet screen beneficiation. High grade pockets have developed locally, with the potential for refractory grade extraction. A major feasibility study of the Mitchell Plateau bauxite deposit was completed in 1983. Due to the unexpected severity of the downturn in the alumina market, development of the project has been deferred.

Jan 1, 1984

By Erie F. Wolstenholme

The purpose of this paper is to describe work undertaken, within the System Dynamics Research Group at Bradford Management Centre, into the development and application of a System Dynamics model of an international mineral industry; aimed at providing a basis for analysis of the interrelationship of supply, consumption and price over time, under different production and stocking policies. A review is presented of some of the major characteristics and problems associated with such industries. This is followed by an outline description of the model and the way it has been applied to examine various supply responses, in the light of changing consumption patterns. Demonstration results deal with model validation and with analysis of international buffer stocks and conflicting supply policies on the historic situation in the copper industry.

Jan 1, 1979

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By Robert Rennie, Taylor Davies, Ahsanul Rafi

Electric locomotives powered by extensive electrical cabling systems were prevalent in the mining industry in the early days of the 20th Century [1]. Since the movement of tethered electrical mining locomotives was limited, the advent of diesel-powered mobile mining equipment provided more flexibility. This led the mining industry to be dominated by diesel-powered locomotives for most of the 20th Century and the entire 21st Century, to date. However, diesel power has certain drawbacks. Diesel-powered vehicles produce tailpipe emissions such as diesel particulate matter, carbon dioxide, sulfur dioxide, and nitrogen oxide. Mine workers exposed to these emissions were, and continue to be, subject to health issues such as respiratory problems, increased risk of lung cancer, and cardiovascular disease. [2][3]. Extensive ventilation systems are required to dilute the diesel exhaust and dissipate the heat generated by these vehicles. Moreover, as mines are getting deeper due to depleting resources, ventilation costs in diesel-powered mines are becoming increasingly high. These factors, coupled with the trend towards greenhouse gas (GHG) reduction in mine operations, has allowed zero-emission electric locomotive systems to gain traction. As lithium-ion battery technology is becoming more advanced, battery-powered electric vehicles can now perform duty cycles comparable to those of diesel-powered vehicles. Although battery-electric vehicles (BEVs) are comparable to diesel-powered vehicles in terms of mobility, they have certain limitations. For instance, the amount of onboard energy is limited by the battery energy density and specific energy. The MT42 diesel haul truck from Epiroc, for example, has a fuel tank capacity of 580L, which is equivalent to around 1450 kWh of net electrical energy [4]. The electrified version of the MT42, on the other hand, has an onboard battery with 375 kWh of usable energy weighing around 4.9 metric tonnes [5]. Moreover, storing and refueling of diesel-powered vehicles is simple and quick, whereas battery energy storage and charging systems require extensive infrastructure development. Charging time is mostly limited by battery chemistry and design. Due to these limitations, the benefits of battery-powered mining vehicles are more likely to be realized with proper planning and optimization of the BEV fleet. This includes optimizing mining layouts for BEV use, charging infrastructure design, and management of onboard energy storage systems.

Jun 25, 2023

By A. C. Burrow, R. P. King

A dynamic model that predicts the variation of carbon content with time in the argon-oxygen decarburization (AOD) process has been developed. The model recognizes three distinct zones in the AOD vessel: the tuyere region in which the blown oxygen reacts very rapidly with the metal components in the molten alloy; a region in which bubbles of inert gas and oxide drop lets rise through the molten alloy; and a zone in which the slag layer can interact with the molten alloy. The process is dynamically controlled by the rate at which dissolved oxygen, produced on the surface of rising oxide droplets, and dissolved carbon diffuse through the molten alloy to react at the surface of the rising bubbles. The rate at which carbon and oxygen react on the bubble surface is assumed to be intrinsically very fast. Predicted decarburization rates compare reasonably well with rates measured in the AOD vessel at Middleburg Steel and Alloys. The model has been developed primarily to allow development of a time-optimal blowing stategy for the AOD vessel.

Jan 1, 1990

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Felicity Lloyd, Stuart Kearns, Roger McLimans

The metamorphic terrane of southwestern India is a geological environment containing ilmenite source-rocks, transport drainage systems, and resultant beach sand deposits that contain altered ilmenites greater than 60wt% TiO2. As such, this environment provides a geological laboratory, from source to deposit, for the investigation of ilmenite origin, alteration, and geochemical character. Ilmenite samples from potential source rocks, river sands, and beach sands all show degrees of alteration and a variety of alteration textures (iron leaching) producing leucoxene (here defined as >70 <90wt% TiO2) and progressing to rutile (here defined as >90wt% TiO2). Distinct alteration textures are specific to different source rocks and are used together with trace element geochemistry as provenance criteria. Ilmenites are classified on the basis of their trace element content. In India, the ilmenites are classified principally according to the Mg, Nb, and Mn content and this signature defines potential source rocks, even where the ilmenite is altered to a TiO2 content of 70wt%. The trace element data may fingerprint source rocks whose ilmenite is more prone to iron leaching and that criterion has application in exploration for higher-grade ilmenites.

Jan 1, 2005

By Graham Taylor, Mandy Agnew

Hardpans developing in tailings storage facilities (TSF) in Australia have been investigated in relation to Acid Rock Drainage (ARD) generation. This research had three main aims. Firstly it was to obtain an understanding of the physical and chemical characteristics of tailings residues which support the in-situ formation of cemented layers and hardpans. Secondly it was to examine how effective hardpans are at reducing ARD generation, and thirdly it was to investigate the promotion of hardpan formation to inhibit ARD and pollutant generation. This paper presents the data collected during investigations into the effectiveness of hardpans to reduce ARD generation. Three basic types of hardpans have been identified and examined: laterally extensive surface hardpans, laterally extensive cemented layers; and laterally discontinuous hardpans developing in locations of seepage. Their mineralogy, morphology, lateral extent, depth and rate of formation are dictated by sulfide and gangue mineralogy and content, milling and depositional techniques of the tailings and the climate. As the sulfides oxidise, acid and heavy metals are generated, while gangue mineral degradation is enhanced, adding to elemental loads. These liberated ions are then available for precipitation of secondary mineral cements through concentration during evaporation. In TSFs where hardpan development is restricted by mineralogy, grain size or climate, hardpan formation can be enhanced in seepage zones (eg. seepage from waste rock dumps) where tailings are exposed to seepage waters laden with heavy metals and sulfate. The effectiveness of hardpans in the inhibition of ARD generation is dependent on reducing oxygen diffusion and water infiltration into the underlying tailings. A reduction in water infiltration will diminish the transport of contaminants developed during sulfide oxidation and subsequent reactions. Water and gas movement through the hardpans at the CSA (Cu, Zn, Pb) and Elura (Pb, Zn, Ag) mines has been investigated. Permeability tests indicate the hardpans have reduced the infiltration rates by 10 to 100 times that of the fresh tailings. Oxygen diffusion rates were calculated and were shown to be up to 1000 times lower in hardpans than in fresh tailings. Such decreases are explained by persistent elevated &apos;degrees of saturation&apos; within the hardpans. These conditions were verified using a conceptual model of sulfide oxidation reactions, which allowed comparisons of diffusion coefficients with modelled and observed depths of oxidation within the tailings impoundments.

Jan 1, 2000

By Ching L. Wu, Bolek Chytrowski, Peter Frobenius, Dale Roberts

During the past few years, the first stage of the Waste Isolation Pilot Plant, (WIPP) which consists of an exploratory shaft, a ventilation shaft, shaft stations, access drifts and test rooms, has been under construction. Construction of the first stage is scheduled to be completed in the summer of 1983. The U.S. Department of Energy (DOE) is constructing the WIPP facility to demonstrate the feasibility of disposing of defense-related nuclear waste in the bedded salt deposits of the Delaware Basin near Carlsbad, N.M. The project promises to be a proving ground for underground nuclear waste storage facility design and construction. The completed underground plant will extend over an area of 647,500 m2 (160 acres), and 1,360,500 metric tons (1,500,000 tons) of salt will be excavated. The first stage of the project, the Site and Preliminary Design Validation (SPDV) Program, provides for full-scale construction of the major components of the underground facility. Shaft construction and underground development are described. Rock bolt installation is performed as required for roof control. Geotechnical instrumentation is installed to monitor the behavior of underground openings. Direct observation of the constructed shafts, shaft stations, and underground openings is expected to confirm the adequacy of the underground design and allow full-scale construction of the first U.S. underground nuclear waste storage facility to proceed.

Jan 1, 1983