Search Documents

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

The choice between EPB - and Slurry Shields is influenced by the following factors: grain size distribution, cohesiveness, occurence of boulders, occurence of gas, feasibility of soil separation and muck disposal, and settlement properties of the soil. The simple equation cohesive soils = EPB Shields and non cohesive soils = Slurry Shield is very often superimposed by other facts. For example, the occurence of a large amount of boulders in weak cohesive soils, where the application of roller discs is not recommendable, may lead to the use of a Slurry Shield with a rock crusher, thus accepting the disadvantage of a sophisticated separation plant; whereas the occurence of contaminated groundwater or gas may exclude the use of a Slurry Shield. In the following examples the choice of a Slurry Shield or EPBS will be explained and justified with regard of the above factors.

Jan 1, 1995

By G. M. Smith

Several significant past and present producers of high grade and bulk tonnage gold ore from southeastern California and southwestern Arizona can be empirically and genetically linked to regional peraluminous magmatism which occurred during the late Cretaceous and early Tertiary. Geological relationships and geochemical characteristics from the Fortuna Mine area will be described and compared to those of the Tumco Mines area. Each of these historical gold producers is viewed as a morphologic end member in otherwise genetically linked metallogeny. Cold-quartz veins at Fortuna can be directly linked to peraluminous pegmatites both physically and mineralogically. Silica-magnetite±spidote±garnet rock which occurs as relatively barren, discontinuous, foliation- parallel horizons at Fortuna, but as high grade gold ore at Tumco, is interpreted as replacement of calcareous units during the same episode of peraluminous magnatism responsible for the gold vein mineralization. Whole rock and trace element data from pagmatites and aplites of the Fortuna and Tumco areas, together with data from the Gunnery Range batholith of southwestern Arizona, indicate that the magma series (after Keith, 1984) responsible for the gold metallogeny is peraluminous calcic, and is quite rich in sodium.

Jan 1, 1987

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007

By Kenneth J. Leib, Laurie Wirt, M. Alisa Mast

Chemical-constituent loads were determined for an alpine stream in southwestern Colorado that is affected by natural acid drainage from weathering of hydrothermally-altered rock and from acidic metal-rich discharge from abandoned mines. Base-flow loads were compared to storm-related loads using a tracer-dilution approach. A rainstom occurred during the tracer injection, providing the opportunity to measure metal loads before, during, and after storm runoff. Chemical-constituent loads during the storm increased by 1 to 2 orders of magnitude relative to base-flow conditions. The increase in loads was related to two distinct periods; (1) a flush of higher concentrations that occurred soon after rainfall began, and (2) the peak of storm runoff. The initial flush-having no measurable change in discharge--contained the highest loads of trace metals and dissolved iron. The chemical character of peak runoff was distinctly different, as evidenced by the highest loads of total and dissolved major elements and total iron.

Jan 1, 2000

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By R. V. Hunter, J. F. T. Agapito

Introduction Significant increases in extraction ratio on the order of 6% to 8%, equivalent to as much as 142 t/m (48 st per ft) of panel, have occurred at the Big Island trona mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-lying trona beds at depths of 250 m and 260 m (820 ft and 853 ft) in the Green River Formation in southwestern Wyoming. Conventional room-and-pillarmining originally was conducted in panels with extractions of 5 8% to 60%. The use of yield pillars has allowed the panel extraction in increase to 66%. Continuous machine mining was introduced, with a 64% extraction ratio using long, narrow pillars and wide rooms. Further improvements in resource recovery seem feasible in light of present mining experience. The rock mechanics program consisted of field instrumentation to determine the pillar and roof response hole locations. to mining and computer modeling to evaluate the stability of various layouts, which were then adopted for mining. Mining background Stauffer Chemical Co.&apos;s Big Island mine and refinery are located 40 km (25 miles) northwest of Green River, WY. Underground mining operations supply trona, a sodium mineral, to the refinery to produce soda ash. The room-and-pillar method is used to mine two 3 to 3.6 m (10 to 12 ft) thick, flat-laying seams at depths of about 250 to 260 m (820 to 850 ft). Mine production in 1986 was 2.3 Mt (2.5 million st). These were supplied through both conventional and continuous machine mining sec-

Jan 1, 1989

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel project, a U.S. EPA/ DOJ CSO Long Term Control Plan Project. The system will provide at least 10.3 million gallons of storage in a 16.5-foot finished ID and 6,660-foot-long rock tunnel. The system will reduce both overflow volume and number of overflow structures on the Cuyahoga River. The project includes deep drop shafts and more than 3,000 linear feet of 48 to 96-inch I.D. sewers installed by trenchless construction methods. This paper will discuss the project background, ground conditions, and other challenges overcome during the design phases.

Jun 13, 2023

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By L. W. Stanger, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Gold mineralization at the Mercur Mine was controlled primarily by structure and secondarily by lithology in Mississippian-age sedimentary rocks. Gold was localized where Sevier-age high angle northeast-striking faults are intersected by younger northwest-striking fault zones. The Lulu Graben is a northeast- striking fault zone composed of a south-dipping master fault coupled with subsidiary or antithetic faults. The Twist Fault zone, a sinuous, low-displacement , north-striking zone of fracturing, bisects the graben. Large- tonnage disseminated ore bodies formed east of the Twist Fault zone within silty, thin-bedded, bioclastic carbonates. West of the Twist Fault zone, gold was restricted to rock near peripheral faults surrounding a subvertical collapsed pipe developed within the graben. An overlying thick carbonaceous shale capped the ore zone. Presence of abundant limited- displacement faulting and of hydrothermal jasperoid is associated with cartonate-hosted disseminated gold. Conversely, increased fault displacement and widespread brecciation are associated with reduced dissemination of gold into normally receptive carbonates.

Jan 1, 1990

By L. You

Theoretical and analytical analyses of three mitigative measures- plane fitting method, trenching, and tension cable led to the development of a total protection plan to eliminate or reduce damages to the residential structures subjected to surface movements caused by underground longwall mining. The protection plan was applied to twelve residential houses and two external garages. The success rate is overwhelming. This paper describes the methods employed for protection and results of those case studies.

Jan 1, 1986

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Feb 24, 1997

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

By T. T. Gronfors

The excavation process and equipment used for excavation join firmly each other. By changing the process or method, the construction of equipment may be altered essentially. It has been possible to develop a wholy new type of hydraulic boom for tunnelling, when only parallel drilling instead of V-cut is used. The utilization of controlled blasting has made small holes more desirable. So the controlled blasting has had an influence on the selection of drill steel equipment and in this way also influenced the construction of the equipment.

Jan 1, 1970

By Philip K. Chan

Batu Hijau is a new copper and gold mine located on the island of Sumbawa in the Republic of Indonesia. This paper details the design and construction of the Batu Hijau overland conveyor, one of the most challenging efforts of the project. The 1.8 m wide, 5.6 km long conveyor has a design capacity of over 10,000 mtph and carries primary crushed ore through the steep mountains of Sumbawa, which necessitated a 160 m vertical downhill section, a 75 m vertical uphill section, ten vertical curves and one horizontal curve.

Jan 1, 2000

By Frank W. Bowdish

During the early 1960&apos;s, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978