Search Documents

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Mustafa Kumral

The study area is located in the Alpine-Himalayan zone in Turkey. Geologically, this is a very complicated region, and the rock units generally are divided into two groups as either allochthonous and autochthonous. Tectono-stratigraphically, the units are Paleozoic quartzite, black limestone, arkosic sandstone, interlaminated radiolarite and Triassic limestone, thick Jurassic limestone, detritic limestone with alternating Eocene Nummulites beds and cream-green marl, Miocene siltstone, and ophiolite. Trachyte, trachyandesite, feldspathoidal trachyandesite porphyry, tuff, and pumice formed by volcanism during the Plio-Quaternary also are present. Recent alluvium and slope detritus locally cover all the other rock units. A number of sulfur outcrops occur in the area. Among them are outcrops at Keciborlu, Yelliyatak Hill, Buyuk, and Kucuk Kukurt Dere. The most important sulfur deposits are found in volcanic tuff and siltstone-marl, and they include highly organic material. Sulfur may accumulate around recent gas diffusions and also as massive formations. The information about local geology and sulfur isotopes shows that the sulfur originated From the crust and probably comes from organic-rich Paleozoic and Triassic units. The sulfur did not move between Triassic and Pliocene time. However. Plio-Quaternary volcanism did cause movement of the sulfur, and this was followed by formation of the secondary sulfur due to post-tectonic thermal activities and the mixing of other surface waters.

Jan 1, 1999

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By Heinrich Schubert

In many unit operations, there are more or less developed turbulent flow conditions. Then, macroturbulence influences the transport phenomena of the particles and microturbulence controls the stresses acting on fluid and solid particles or agglomerates as well as the collisions between particles. Consequently, these conditions have to betaken into consideration for modeling and optimization. The results of corresponding approaches are demonstrated taking classification and flotation as examples. But, at present, extensive simplifying assumptions have to be made.

Jan 1, 1989

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By Yerkezhan Madenova, Kairat Kalmurzayev

This study intends to demonstrate the engineering application of ground penetrating radar (GPR) that would enable site engineers to prevent the high cost of blind drilling. At the tailing dump located in Zhairem Mining and Processing Plant, the challenge of sheet pile driving is encountered due to the indefinite watertight clay layer deposition depth that serves as a protective layer against groundwater contamination. A numerical model of the soil underlying the tailing dump is built using the existing hole data to compare and confirm the existing geological cross sections for three profile lines along the south and southeast parts of the tailing dump. GPR is employed to investigate the subsoil geological structure and detect the watertight clay layer deposition. On the basis of radargrams tied to the existing borehole data in the numerical model, 21 drill hole locations are suggested to assess and confirm the clay layer depth along profile lines at the tailing dump. The drilling results of the suggested holes confirmed the expected depth of the clay layer. It is concluded that GPR is a practical and economic subsurface mapping method that can prevent the high cost of blind digging of the ground and orient the drilling operations effectively.

Jan 12, 2023

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By Th. Petropulos

The Zn-Ag-Pb mineralization zone near Molai (Greece) was explored by more, than 60 drillholes. Promising results led to the decision of additional drillholes in order to confirm the expected spatial extension of the deposit. A multiobjective approach is described which optimizes the location of a set of 5 additional drillholes. The decision is based on estimation errors for grade, thickness and depth of the main ore bearing layer, with respect to cut-off values for grade and thickness. The linear combination of these variables defines a favorability index which is used for mapping optimal drillhole locations. The map shows several clusters of favorable cells. A declustrering algorithm is used to select a representative cell for drilling in each cluster.

Jan 1, 1989

By Douglas E. Rawling

The successful genetic manipulation of T. ferrooxidans is partly dependent on an understanding of the molecular biology of the organism. For optimum controlled expression of foreign DNA in T. ferrooxidans it is important that donor DNA is derived from bacteria that are genetically similar to T. ferrooxidans or placed under the control of T. ferrooxidans transcriptional promoters. Several structural genes and their controlling regions from T. ferrooxidans have been isolated and their DNA sequenced. These include the genes that encode the nitrogenase enzyme (nifHDK genes), glutamine synthetase (glnA gene) and the recA gene. These genes and the identical genes from a wide variety of other bacteria have been compared at levels of DNA sequence, protein sequence. Where possible, gene expression as well as transcriptional control and protein function of the cloned genes were tested in the enteric bacterium Escherichia coli. The two genes involved in nitrogen metabolism were either expressed or possessed the necessary elements for expression in other bacteria. In contrast the recA gene was not expressed in E. coli from its own promoter. The two gene products that would be tested (glnA and recA) were fully functional in E. coli. The relevance of these findings to the genetic manipulation of T. ferrooxidans is discussed

Jan 1, 1989

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, in spite of the low-grade nature of the ore, has become one of the largest production-scale and most profitable non-ferrous metal mines in China. The successful application of hydrometallurgy as well as proper engineering design are the key factors for large-scale development of the Zijinshan gold-copper mine. In this contribution, the practical experience acquired in the development of the Zijinshan gold and copper mines is summarized. This covers most aspects of the production process including mining, beneficiation, ore stacking, heap (bio)leaching, carbon-in-leach, solvent extraction, electrowinning, wastewater and tailing treatments. The authors believe that this practical experience will not only help to promote the development of hydrometallurgy, but can also serve as a model for other gold and/or copper plants around the world.

Jun 3, 2020

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By F. H. Muge

This paper intends to present a general methodology implemented in a software package and which can be applied, whatever the exploitation methods, mining constraints and time basis, to mine planning and production schedulling. Examples are: presented covering the medium-term and short-term planning procedure and the production schedulling for two underground mines located in the South of Portugal (Neves- -Corvo and Aljustrel Mines). Both are complex suiphide orebodies with differ- ent exploitation methods (Neves-Corvo: cut-and-fill; Aljustrel: Long-hole stop- ping).

Jan 1, 1992

By K. Sasaki

Diffusion phenomena in mine airways are important to trace gas and dust introduced into mine ventilation flows. Authors have carried out tracer gas measurements to check mine ventilation using concentration-time curves measured in mine airways, however dispersion mechanism to enhance effective diffusion have not been cleared. A numerical model using discrete tracer points dosed into tube flow has been presented to simulate their movements in consideration of turbulent velocity profile and fluctuation. Numerical simulations have been carried out to predict distributions of dosed points in tube flows with turbulent velocity profile, turbulent intensity profile and Reynolds stress. The numerical simulation results show that a combination of turbulent velocity profile and fluctuation creates extremely large dispersion of points in longitudinal direction and concentration curve with long tail was observed. This dispersion by velocity profile and fluctuation contributes large effective diffusion coefficient compared with original diffusion coefficient dominating in uniform velocity fields. Furthermore, the effect of Reynolds stress on the concentration-time curves is discussed.

Jan 1, 2009

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By Gordon R. Wicker, John A. Cole

Although the evaluation of autoclave oxidation for Getchell ore was begun nearly 40 years ago, its ultimate implementation in 1989 represents the first substantial improvement in the economics of processing this refractory ore. Sulfide ores at Getchell were previously roasted prior to leaching (in the 30's and 60's), resulting in somewhat lower recoveries than are currently realized by autoclave oxidation. Recoveries on the order of 90% are expected from the high-arsenic sulfide ore over the expected 10-year mine life.

Jan 1, 1990

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998