Search Documents

By Robert C. Jones

The Henderson Mine, a new large scale underground development, is being developed by AMAX. The mine site is located about 50 miles west of Denver, Colorado, adjacent to the east side of the Continental Divide. The mine's three access shafts are in a narrow alpine canyon at an elevation of 10,400 feet. The ore body of molybdenite is to the south of the shafts, 3,000 feet below the surface of nearby Red Mountain. The ore extends over 800 feet vertically and is about 1,700 feet by 2,200 feet horizontally. The eastern and southeastern boundaries of the deposit are still to be defined at the present time. Development mining is advancing at the mine site on a three shift, seven-day basis at the rate of about 2,000 feet per month. About twelve miles of heading have been driven at the present time, and work to sink No. 3 Shaft has started. Development mining was begun in 1967 with the sinking of No. 1 Shaft. This shaft is fully concreted, 23 feet in diameter and 2,441 feet in depth. It is the mine ventilation exhaust conduit. It is also used for development muck hoisting, stand-by mine water pumping and secondary access to the 8,035 foot level. This level is the mine exhaust ventilation level and was mined principally by conventional rail mining methods. From this one station at the 8,035 foot elevation a 5% ramp was driven to the initial production horizon at 8,100 feet with diesel rubber tired mining equipment. Subsequent mining has been entirely by mobile diesel equipment at the mine site.

Jan 1, 1974

By M. R. Leonard

It is estimated that between 5 and 15 pounds of solid waste are generated monthly by each individual. Finding a final resting spot for such waste is an important matter. In the "good ole days," dumps of every description and condition were available. Not so now. Almost all states have adopted and are enforcing strict regulations regarding the disposition of solid waste. Many companies, owing to the nature of their business, have potentially good waste-disposal sites available. Cleveland Quarries Company falls in this group; but in spite of our having state and county permits, opposition by the local community denied us the opportunity to provide a needed local service.

Jan 1, 1974

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By John Conway, Gerald Bennett, John Herrick

Research efforts which have led to reduced resin bolting costs at White Pine Mine are described. Key factor was development of the capability to drill small holes (1 1/8 in. diam) in the hard (20,000-30,000 psi) White Pine roof rock. Economic data comparing the 1 1/8 in fully-grouted Resin Bolt to the conventional 1 3/8 in fully-grouted bolt is also included. The development of a method which allows the Resin Bolt to hold itself in the hole thus removing the requirement for the operator to break his "work momentum" while he stops and waits for the resin to set is also described. This technique increased bolter productivity by 23% in a recent full-scale unit test.

Jan 1, 1974

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By Jacob Feld

Introduction The best way to eliminate the possibility of rapid excavation in tunnel work is to start an argument between Owner Engineer and Contractor. And arguments are readily started when work is progressed without a frank open agreement on the rules of the game. Fifty years ago a tunnel contractor took a job to excavate and line a tunnel, providing all labor and materials under the guidance and continuous instruction of the Engineer who provided all survey work, checked each new heading and set the lines for the next round of drill holes, usually designed and ordered protective measures, kept record of progress and controlled payment for the work. In my first job in a tunnel, muck cars were loaded by hand and hauled by donkeys. Progress was, at today's criteria, not rapid. The Contractor or in the case of a large concern, his executive field representative was always at the site, knew most of his men by name, and there was a mutual feeling of respect between him and the Engineer in charge of the work. Misunderstandings were cleared up when they came up, expeditiously and fairly, even though satisfaction was not always expressed. The Owner came for the ground breaking and usually for the holing through shot. The Owner had full reliance on the Engineer's ability and integrity. The Engineer recognized the Contractor's expertise in being able to man the job and produce results.

Jan 1, 1974

By M. S. Walton

A conference attended by a limited number of invited participants was held last September in Denver under the auspices of the Underground Construction Research Council of ASCE funded by the National Science Foundation (RANN) to explore the problem of accelerating the transfer of advanced geophysical technology, used principally in the petroleum exploration industry, into more effective and widespread use in subsurface investigations for underground construction. There are technological problems, but technical difficulties and unfavorable ratios of benefits to costs are not the major obstacles. The problem centers on the complex way in which potential net benefits are translated into effective incentives to innovate for each actor in the complex web of individual, corporate and institutional entities involved in the planning, designing, building, funding, operation and ownership of major underground construction projects. The entities responsible for site investigation, design concepts and specifications do not directly bear the risks of unanticipated costs and failures, nor directly gain from savings. The conventional unit-price construction contract is strongly implicated in blocking innovation. Problems of risks and incentives, more than technical feasibility, must be solved before large investments in technical adaptation and adoption can occur.

Jan 1, 1974

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974

By M. E. Poad, Donald Ross, G. G. Wadell

Because of the "energy crisis" emphasis has been placed on bringing coal mines into full production faster. To accomplish this, more is involved than a rapid excavation system. Mine design should have the freedom within the law to customize as mining conditions dictate as long as the maximum safety of the miner is insured. A year ago, safety was the most prominent "social-human factor"--now, safety and energy self-sufficiency are primary to our national policy. The Single Entry research program as designed satisfies both. It investigates the hypothesis that a single-entry system, for longwall development, supported in the center by open cribs and divided by a fire-resistant partition, can be regarded as being equivalent to or better than a multi-entry system. This paper provides an explanation for the use and advantages of a single entry system in development for longwall mining, explains the problems anticipated with single entries and presents the research approach needed to evaluate and solve the problems. Under study are ground control, ventilation, fire and explosions, emergency procedures, and industrial hazards. Described are measurements data on crib and roof bolt loads as entry heading advances and longwall abutment load is superimposed, stress field determinations and preliminary structural analysis of the double and single entry, and methane liberation and ventilation records as entry advances. Some of the mine operation problems and waivers of mining laws will be discussed. This project is a complete system study having progressed approximately two years in a five-year program.

Jan 1, 1974

By L. W. Saperstein

One of the most critical skills developed by underground coal miners is the ability to interpret natural warning signals in terms of impending roof failure. A miner receives a variety of signals which can be called warning and which can be classed broadly by sense: aural, visual, and tactile. This paper concentrates on those signals which are airborne and audible. These signals are creaks, cracks, pops, groans, snaps, booms, tears, rips, and other assorted pulses which emanate from the roof strata, coal pillars, and artificial support in response to the stresses induced by the mine opening. These pulses are sometimes referred to as "talk". Although it is clear that miners rely on roof talk to assess the roof's stability, it is not clear of what roof talk is composed. It has been described in a variety of figurative ways, but has not been scientifically characterized. As will be shown shortly, the purpose of this research is very specific. The ramifications, however, are very broad, and are, indeed, still being followed.

Jan 1, 1974

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By Samuel Sigman, Martin M. Cooper

A basic ingredient for rapid tunnel excavation is material handling. In construction of tunnel projects in urban areas material handling requires additional input to maximize performance. Urban projects share the same problems experienced in all tunnel construction and they must be dealt with. Howeve.., Urban constraints add a larger dimension. APPLICATION ENGINEERING A MUST A word of caution. To achieve increasing speed of excavation in tunnels whether in Urban areas or elsewhere will require much creative thought and energy. It would be a false premise to assume that major breakthroughs will result from this conference, or shortly thereafter, or to hope that a success here or there can translate into a universal solution. The reality, as we see it is that rapid progress and great economies will accrue on any given project only if effective application engineering is carried through. By all means take advantage of past experiences but, do not at the peril of costly undertaking, blindly accept the program of a successful job elsewhere as automatically suited to your project. Tunnel construction in urban areas is at best a difficult undertaking made more difficult in this period of greater awareness of environment, of conservation and of the quality of living by sophisticated urban communities,. A construction job represents a necessary nuisance to urban communities. To minimize this nuisance many regulatory laws are adopted. These regulations can and do slow down tunnel jobs and pyramid costs.

Jan 1, 1974

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By Russell C. Drew

The United States has long been recognized for its ability to marshall the many tools of its scientists and engineers to meet national threats or crises. Two major World Wars, the Dust Bowl, the Soviet Missile threat, Sputnik, and more recently the Energy Crisis have stimulated military weapons development, massive land reclamation and water management programs, NASA, and the Space Program, Project Independence, and soon a new agency, the Energy Research and Development Administration. While our record of successful responses to these major national concerns lends support to the expectation that we will succeed in dealing with the current energy problem and potential future crises as well, the crisis mode of response is becoming increasingly wasteful of funds and human and natural resources. This waste, while always of a concern, is a more important factor than previously because of the accelerating pace at which the world has been shrinking, relatively, in comparison to its human population and that population's increasing demand for resources, both renewable and nonrenewable. If present growth patterns continue, in the year 2000 there will be two people to feed, clothe, house, and satisfy for every one person that existed in 1970. On a finite planet, with finite land areas, limited resources, and only partial understanding of the means by which future problems can be addressed, one of the major threats to mankind will be scarcity and one of our major challenges will be better management of our resources. The challenge will be to guide Federal investments in R&D that are of sufficient magnitude and in the proper

Jan 1, 1974