Search Documents

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state, and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Capital cost, operating cost, and present and future regulatory requirements will be primary factors to be considered by engineers. This paper outlines procedures and gives examples of advanced engineering practices that have achieved efficient pollution control systems in the steel and nonferrous industries.

Jan 1, 1968

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By Ronald G. Schmidt

AND SOME RIN UP HILL AND DOWN DALE, KNAPPING THE CHUCKY STANES TO PIECES WI' HAMMERS, LIKE SAE MANY ROAD MAKERS RUN DAFT. THEY SAY IT IS TO SEE HOW THE WARLD WAS MADE. Sir Walter Scott St. Ronan's Well - 1824 In the minds of many, geologic exploration has advanced little since the early nineteenth century. In truth, despite the development and refinement of new and potentially valuable technological tools, the approach or philosophy of the explorationist has received meager attention in professional literature. In many areas, the explorationist relies upon experience, subjective judgement and general intangible inspiration, often traveling together under the misleading pseudonym of "art," in achieving both an exploration plan and in making the myriad day to day decisions necessary to the execution of that plan. Without a solid, objective basis for decisions, exploration under this concept is little more than guesswork largely by intuition, and it is small wonder that many exploration programs flounder in a sea of over-expenditure inefficiency or fail to fulfill their expected goals within the funding which has been provided. From a rational management point of view, such a state of affairs is frustrating and inconsistent with the application of the same scientific principles which are presumed to be the basis for the exploration methods which are used. This somewhat presumptuous point of view cannot be extended as a general condemnation of the many exploration programs which are both technically and economically successful. On the other hand, the

Jan 1, 1968

By Robert N. Morris

Ladies and Gentlemen: It is a distinct pleasure and honor to appear before you representing the railway industry as I do, but there is a much closer personal relationship. I am a graduate Mining Engineer and worked in the coal industry for 15 years prior to becoming a railroader only 4 ½ years ago. I have been a member of AIME most of my adult working life and am currently active in the Washington, D. C. Section. While having been in the railway industry only a short time, I have become involved during the recent period of innovation and development of the new railroad technique known as unit train service. I have had the privilege of helping to work out a number of unit train movements to both electric utility companies and to a major steel concern, handling coal from mines on the Southern Railway to the consuming plants. On Southern, our unit trains are all of what I shall describe as shuttle train operations whereas within the railroad industry today several types of service are characterized as unit train service and many don't offer comparable efficiencies.

Jan 1, 1968

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By F. A. Renninger

The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Few individuals ever have occasion to purchase mineral aggregates for anything other than use for decorative shrubbery beds or walkways. They may, however, buy ready-mix concrete for a new patio, bituminous concrete for a new driveway, concrete blocks, or other building materials for a new room and never realize that the primary ingredients of their purchases are either direct or indirect products of the mineral aggregate industry. The average person driving past an operating crushed stone quarry or an active sand and gravel pit rarely realizes the economic impact the industry, represented by that operation, exercises on the general economy. He is not aware, nor does he really care, that elements of the modern comfortable environment to which he has grown accustomed rely to a great extent on the products of the crushed stone and sand and gravel industries Iron and steel, glass, cement, agriculture, and highway and building construction are but a few of the major industries to whom the products of the mineral aggregate industry are basic. Without these industries or without the stone, sand, and gravel basic to them, most of the major elements of our modern day civilization would be non-existent.

Jan 1, 1968

By L. H. E. Weyher

In a previous paper presented at the 1966 Annual Meeting of AIME we reported our work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal.' The initial evaluation based on that work demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper we presented selected test data that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of our data as follows: ? Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity- versus-pressure drop expressions taken from the literature on classification cyclones.

Jan 1, 1968

By M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. Flotation responses of these minerals in the presence of potassium oleate and sodium silicate are presented and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium¬ bearing minerals such as fluorite from calcite (1,2,3) and scheelite from calcite(24) and apatite(2,5) almost always involve the use of sodium silicate, for example. The mechanisms by which sodium silicate functions as a depressant are still not understood; this fact is probably due to a number of reasons. That is, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species. (6) In addition, the type and concentration of these species depend on the ratio of Na20 to Si02, the concentration of sodium silicate, and the pH of the system. (6) At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant.

Jan 1, 1968

By Robert C. Bacon

The first commercial installation of the Dashaveyor has recently been completed at the White Pine Mine in Northern Michigan. After four years of development work, including prototype testing, and pilot plant operation, this new and unique system is being tested under operational conditions. Many of you may be familiar with the concept through numerous articles which have appeared in the technical press. But this discussion of the system will be simplified and less time consuming with the presentation of a portion of a film showing the Dashaveyor in actual operation. After the movie, I will show some slides which will supplement and clarify it and hopefully lay the basis for questions you will undoubtedly wish to ask.

Jan 1, 1968

By F. Forbes

For many years, the Machinery Division of Dravo Corporation has been designing and constructing bins and hunkers as part of overall plant facilities. We have designed bins to handle a variety of materials including coal, coke, iron ores and concentrates, sintered and pelletized ores, calcined and raw limestone, bentonite, alloys for BOF shops, and even cast iron chips from machining operations. We, along with everyone else in this business, have had our bin problems. The bins either plug, rathole, segregate, wear out, flood the discharge device, or overload it. Surprisingly, sometimes they have worked. As engineers, it has long concerned us that something as important as bin design should be so imprecise and that it has been so conspicuously avoided in research and in literature. In past years, rule-of-thumb design criteria had been to keep the sides of the bins as steep as possible and the outlets of the bin as large as possible. This criteria led to the design of bins with 600 to 700 side slopes and table feeders which were very large. Unfortunately, this meant trying to fit tall, skinny bins into a layout where minimum building height was required for obvious economic reasons. Like everyone else in the industry, we found that this design procedure was expensive and ineffective.

Jan 1, 1968

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By Thomas W. Mitcham

A program of geological research in support of mineral exploration efforts is outlined. Specific goals are stated, approaches to accomplish their attainment are described, and the type of useful results to be expected are outlined. Because mineral exploration or prospecting has intensely practical goals, research in support of it must be applied research, applied to the problem of maintaining or increasing the discovery rate of the exploration effort. To attain research goals, attention to personnel selection, group structure, and program are critically important, and in about that order. A large percentage of the professional personnel should have had experience in mining geology or mineral exploration, and they all should be prospector-oriented. Structuring in the group should be at a minimum, with wide allowance for the kind of independent research which is essential to the nurturing of on-target creativity. The program should be field-oriented, and it should include a wide representation of those subdisciplines of geology which are applicable to mineral exploration. The types of results to be anticipated include improved or new conceptual models for various types of orebodies and their settings from which new ore guides can be derived, new exploration techniques, and the development of a knowledge bank for various aspects of the exploration effort.

Jan 1, 1968

By Thomas P. Meloy

Theoretical development of comminution models has come about in the last 10 years. These models assume that the material being broken is homogeneous and that the compression or energy wave is uniform throughout the specimen. Obviously, this is not the case because most comminuted materials are rocks with either many phases and/or definite grain size. The mathematical models deriving the size distribution of daughter fragments resulting from the comminution of brittle, single particles are of two schools. The first model, proposed by Gilvarry in 1961, was based on the concept of volume, surface, and edge flaw activation. The second, proposed by Meloy in 1960, was based on the concept that the crack density is a function of the energy in the comminution wave. The flaw theory has run into increasing theoretical problems and is now being abandoned. On the other hand, the crack density theory has been expanded and has successfully considered the case where there are inhomogeneities in the comminutive wave. However, the main constraint of a homogeneity in the solid being comminuted has hitherto never been overcome. In this paper, a very general derivation of the crack density model is made for inhomogeneous solids by replacing the assumption of homogeneity with an arbitrary function, P(y), which describes the susceptibility of the material to comminution as a function of position. The restraints on this function, P(y), are very broad and, hence, the derivation is extremely general. General use of the equation derived necessitates a detailed a priori knowledge of both the fracture process and of the physical properties of the material being fractured; this knowledge is expressed in open form as, P(y), the linear probability density that a plane of fracture intersects at point y on an arbitrarily oriented line segment of total length xo through the original particle. From these assumptions, a general expression for the cumulative mass distribution of particles resulting from fracture is then postulated. It is: [ ] where, B(x), is a cumulative mass of material finer than size x, r is the average number of crack,, (y), is defined above and xo is the initial particle size. It is shown that suitable assumptions reduce the expression to the theoretical results of Gaudin and Meloy and to special forms of the empirical equations of Rosin-Rammler, Gaudin and Schuhmann. Semi quantitative agreement is demonstrated by Grimshaw with experimental results of a very complex fracture of heterogeneous sandstone blocks. A need is expressed for more theoretical development of P(y), and a more extensive experimental study of both homogeneous and heterogeneous fracture. The full mathematical derivation is presented for the first time in this paper. The general implications of the equation and its application are also discussed.

Jan 1, 1968