Search Documents

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Fred T. Towne

Recent developments in fine grinding by the means of mechanical impaction are the result of continuing improvements in modern machine construction. This is especially true when related to the bearings and mechanically operated parts of impact mills. These improvements allow manufacturers to increase the speeds of the impacting members Most of the more common forms of size reductions, such as percussion, pressure, friction and sectioning, or cutting were at one time accomplished by human hands. These actions were transferred to machinery. Originally of limited application, their use widened as industrial materials and construction became more sophisticated.

Jan 1, 1965

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By Haydn H. Murray

Kaolin is an important industrial mineral because it exhibits desirable properties in many applications and because of its relatively low cost, Approximately 2,000,000 tons of kaolin from Georgia and South Carolina are processed and used commercially in the United States each year. Strictly defined, the name kaolin is applied to a group of hydrous aluminum silicates of which the mineral kaolinite is the most common. Kaolinite has such desirable properties as natural whiteness, chernical stability, non- abrasiveness, and very fine particle size. Kaolinite particles are characteristically thin, flat, and hexagonal in outline. The particles range in size from submicron to as much as 40 microns (equivalent spherical diameter). In addition to the general properties mentioned in the first paragraph, it is soft, has low viscosity at high solids content in many systems, is readily wet and dispersed in water and some organic systems, and can be produced with a controlled particle size distribution. Some of the important physical constants of kaolin are: specific gravity, 2.60; index of refraction, 1.56; hardness (Mohs scale), 2; fusion temperature, 1850°C; dry brightness, 78-92 percent.1

Jan 1, 1965

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By E. D. Hummer

During the planning phase of the fine coal cleaning addition at the Gary Coal Preparation Plant, careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at 1/4 inch, pumping the minus 1/4 inch raw coal to bowl desiltors for desliming, and then cleaning the disliked raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 foot diameter thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh Today the minus 48 mesh refuse at Gary consists of thickened flotation tailings and thickened spiral classifier overflow. The transportation of large quantities of fine wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds

Jan 1, 1965

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By J. D. Grace

[Screening by centrifugal force is an unique, subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon, gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey materiel along the screen, is the SYMONS V-Screen. This screen was designed by Loren Symons, a member of the family that has contributed so much to the metallic and non-metallic mineral processing industries. Among Symons' other outstanding contribution to these industries are the original Cone Crusher which revolutionized reduction crushing practice, the first high-speed horizontal vibrating screen, the original Rod Deck Screen, and one of the earliest vibrating Bar Grizzlies.]

Jan 1, 1965

By John R. Riede

Most modern crushing and grinding facilities are automated to some degree. Some, of course, have a very minimum of automatic control whereas others utilize very complex control equipment. However, with very few exceptions, the re has not been a new basic control philosophy applied in this field in the past seven years. The philosophy has been broadened in scope and applied to larger plants, some of them with data logging and so- called computer control, but almost always the same tried and proven basic control philosophy is the basis for the control system. New types of control devices to better implement the automatic control have been developed and are continuing to be developed. These devices and their application will be explained and the advantages and disadvantages of each will be discussed. Automatic lubrication of plant equipment is most essential, but this paper will not cover these systems. The use of data logging and computer analysis of the data obtained is fairly recent and it is hoped that by careful analysis of this information that new and better basic control philosophy will be forthcoming. This paper will describe the basic philosophy applied in its simplest form to several types of crushing and grinding equipment, and it will describe how it is being expanded to more complex systems. Some of the economics with regard to first cost, return on investment and maintenance will be covered.

Jan 1, 1965

By Alan English

This paper reviews the process control systems used in early commercial pelletizing plants, traces the development of these systems into present day practice, and briefly outlines advanced automation concepts being considered for future installations. It deals specifically with controls for the balling circuit, pelletizing machines, and related material handling and combustion equipment. The importance of instruments for visual observation and data logging is discussed, and the potential use of computer control is evaluated.

Jan 1, 1965

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965

By Stanley R. Riggs

The rocks exposed in the phosphate district are of Neogene age and consist of clayey quartz and phosphorite sands overlying phosphatic dolomite. The Bone Valley Formation is redefined as a marine phosphorite containing primary phosphorite and abundant terrigenous sediments. It contains a Middle Miocene vertebrate and invertebrate fauna and conformably overlies the Hawthorn Formation containing similar invertebrate fauna. A new, unnamed formation, with Pliocene and Pleistocene fauna and containing reworked phosphorite, overlies the Bone Valley disconformably. Its phosphorite is derived from the subjacent Bone Valley by post-Middle Miocene erosion and deposition in stream channels and marginal marine environments. The Bone Valley contains two main types of primary marine phosphorite. Orthocbemical phosphorite, a direct precipitate of microcrystalline phosphorite (microsphorite), occurs as a cement or binder in thin beds. Allochemical phosphorite consists of clastic phosphorite particles that were originally formed as microsphorite on another part of the shelf. Microsphorite was deposited in a very shallow open marine environment which had an abnormally high phosphorous content caused by upwelling currents. The mechanism of deposition is still in doubt, but organisms probably were a major factor. Soon after deposition, microsphorite was indurated, periodically torn up, and the resulting fragments transported and deposited elsewhere on the shelf. These processes account for a great portion of the clastic phosphorite in the Miocene deposits of Florida. The primary fossil skeletal material is of minor importance.

Jan 1, 1965

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965