Search Documents

By Robert R. French

Commercial grade gypsum beds up to 16 feet thick is present in southwestern Indiana. The major deposits are found at a depth of 350 feet to more than 500 feet below the surface. The ore body averages about 75 to 95 percent gypsum. Two companies are currently exploiting a deposit which underlies an area of several square miles near Shoals, in Martin County. Another deposit has been located in southwestern Owen County but has not been developed. The Indiana Geological Survey is currently drilling in Greene County and is considering further exploratory work in Perry end Dubois Counties.

Jan 1, 1965

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965

By Roger Bell

Most modern mines can profit from improvements in information handling. Recording systems in many cases were designed to satisfy certain necessary legal requirements, but not specifically to provide management information. As a consequence, the top managements of these properties work with cost data and production information that is dated, lacking in detail and clouded with supposition. It is the intent of this paper to describe an information system for a mine-plant complex in terms of the type of data, application areas and the existing equipment technology that may be applied to improve this situation. The economics of information processing and data handling will not be discussed in detail. This paper is based on the premise that information is something of value and that information processing like a manufacturing operation works for and is subject to management control. Information, the product, must be of quality, and the cost must be favorable in terms of its use.

Jan 1, 1965

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By K. W. Vincent

This paper, deals with the beneficiation of a low grade Western phosphate to ore. More specifically it summarizes the results of a study made to optimize a scrubbing step in the process, and to provide firmer data for use in plant design. The deposit is situated about 30 miles northeast of Pocatello, Idaho, in the Fort Hall Indian Reservation. It is a bedded deposit and throughout most o the orebody includes three contiguous layers of phosphatic material which differ in P205 content. The J. R. Simplot Company, as operator for a Simplot-FMC joint venture, mines the ore selectively by open pit methods The lower bed containing a nominal 30% P205 is shipped to the Simplot Company fertilizer complex near Pocatello; the middle layer averaging about 24% P205 supplies the FMC elemental phosphorus plant also near Pocatello, The top layer averaging around 16% P205 and designated as mill grade shale is stockpiled for future beneficiation. This paper is concerned with some aspects of the processing of this low grade shale.

Jan 1, 1965

By Paul Soros

A major share of the increase in the energy demands of Ontario province in the next decade will be supplied by bituminous coal mined in the U,S, To be competitive with alternative sources of energy, it is essential that the delivered cost of coal, inclusive of all transportation charges, be kept at a minimum. The Bessemer aid Lake Erie Railroad Company and the Pittsburgh and Conneaut Dock Company are currently building a shiploading terminal at Conneaut, Ohio, to service this tonnage, together with expected increases in coal consumption in the Eastern Lake Erie - Lake Ontario area, (see Fig, 1).

Jan 1, 1965

By Harley G. Pyles

Rotary Percussion drilling has shown great improvement over rotary drilling, when hard roof is encountered. In addition, Rotary Percussion drills have eliminated the need for air drills in many applications. Improved drilling rates have been achieved but roof bolting is still a bottleneck in many operations and the demand for further improvement will continue. Drilling rates beyond current performance is limited by the capabilities of existing drill steels and bits to resist increased horsepower input. The most apparent immediate solution to improved drilling is to increase the strength and rigidity of the drill steels. Drilling experience indicates that a l-1/2" diameter or 1-5/8" diameter hole can be drilled as rapidly or 'more rapidly than the standard 1-3/8" diameter hole. Greater torque and thrust capacities can be achieved through the use of larger O. D. and I. D, steels, however, this is only possible if the larger hole sizes can be made allowable. Large diameter anchorage shells can be made available at a slight extra cost.

Jan 1, 1965

By P. F. Mataich

"Why bother with computer control?" This question and others like it have been heard over and over again by those who have tried to convince operating men that there are sound merits to installing a process control computer. At IMC we have done a great deal of thinking and talking about computer control. In the course of these discussions the operating people have asked a number of questions about computer control. These questions and our answers to them make up the main part of this article. Obviously, the answer as to whether or not to go into computer control will be an individual problem conditioned by your company's circumstances. What I hope to do here is raise some questions, give you an idea of our thinking on the subject, and lay out some general guidelines for you to consider.

Jan 1, 1965

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By Adrian C. Dorenfeld

The concentrator of Bonneville Ltd.* at Wendover, Utah, processes a feed obtained by, solar evaporation of a brine containing sodium and potassium chlorides with minor amounts of impurities. Salable potassium chloride concentrateis produced from this feed in two steps: flotation with amine reagents to concentrate the potassium chloride, and washing of the concentrate with fresh water to reach final grade. In the flotation step emphasis is placed on recovery, whereas the washing step has as its objective the production of salable grade (in excess of 60 percent K20 equivalent), with recovery being important but secondary Ideally, flotation should give maximum recovery at a concentrate grade which will permit washing to salable grade with a minimum recovery loss, thereby maximizing over-all recovery. Except for this relationship, flotation and washing are two separate and distinct operations.

Jan 1, 1965

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By J. B. Moritz

From the beginning, man has concerned himself with the task of controlling the elements and forces about him so as to provide a better and easier life. In the accomplishment of this task, he is required to utilize in the best way possible the resources which are available to him. In many cases, the available resources must bee refined before they are in a useable form. Many products in the mining industry fall into this category, as some form of refinement is generally needed to produce a saleable product. Over the years man developed more efficient ways of extracting the resources from earth through the use of electrical and mechanical devices. A reduction in manual labor, which is a by-product of increased efficiency through machines, has also been enjoyed. The combination of man's senses and new devices has also enabled man to reach a high level of control in the refinement process. Control of a process through machinery and man's senses has been termed an "art." Until recently man's senses (sight, feel) were the only method available for making measurements simply because suitable measurement devices (instruments) were not available. Even today some items cannot be measured and man's senses must be used. However, the development in our instrument laboratories tends to indicate that time will eliminate this. In recent years, control of many processes has been reduced to a science and part or all of the art eliminated. This does not imply that process art should be degraded; however, when a process is reduced to a science, uniformity of the product from day to day is attained. Decreased processing time and more efficient use of additives and raw materials are other benefits that result from control of a process when it is reduced to a science.

Jan 1, 1965

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By Barry Hunsaker

I cannot help but be reminded, as I stand here today, of my boyhood years and heritage, both of which are inextricably tied to this very valley and are, in a: bay, apropos of the theme of this Keynote Session. I remember the scarcity of people. For example, 48, 000 in Phoenix and 436, 000 in the State in 1930 and 65,000 in Phoenix and 499, 000 in the State in 1940. Today Phoenix boasts a population of over 500, 000 and the State a population of 1, 500,000. I remember the' lack of facilities, goods and services, including gas and electric power. I recall stories of my grandfather who had the freighting or teaming contract to haul all the supplies and generating equipment, by wagon mind you, up the old Apache Trail to Roosevelt Dam. . .a three day trip from the nearest railhead which, by the way, was not Phoenix, for it did not merit a railhead on those days, but the village of Maricopa approximately 25 miles south of Phoenix. I remember chopping firewood, heating wash water on an open fire in a No. 3 wash tub at the rear of the house and doing my school homework by the light of a kerosene lamp just 25 to 35 years ago within what is now a large metropolitan area

Jan 1, 1965

By H. W. Seany

Over the years since the initial experiments with underground concreting were made in 1956, attesting to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the, mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other advantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 1, 1965

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965