Search Documents

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By T. P. Weldum

INTRODUCTION Cleveland-Cliffs' operations in Michigan have been utilizing fully autogenous grinding for over four decades. This is but one of the key characteristics of the iron ore processing method that was developed for the extremely fine grained, low grade deposits of the region. Liberation size of the hematite and magnetite ranges from about 30 to less than 1 micron. Typical grinding fineness target to achieve silica grade in the concentrate is 80 to 90% passing 25 microns, or a P80 of approximately 20 microns. After primary grinding, the magnetite ore is first upgraded by rougher magnetic separation. It is then ground to final product size, sent through thickener-sizers utilizing selective flocculation, upgraded again by finisher magnetic separation, and then brought to final silica grade by reverse amine flotation. Hematite ore follows essentially the same route, less the magnetic separation stages. Concentrate is filtered and pelletized, along with con- trolled additions of fluxstone, to ready it for shipping. Iron ore pellets on the water of the Great Lakes have a value of approximately 1.5 cents per pound. GRINDING PROCESS DESCRIPTION Details of the Empire magnetite grinding process flowsheet have been presented by Greenwood and Rajala (1992), and more recently by Rose et al. (2002). The Tilden comminution process for either magnetite or hematite is essentially identical, with the exception of some variations in the excess pebble treatment methods (McIvor and

Jan 1, 2004

By D. Yadon, P. Lee, W. Kelly, C. Stilwell

Rico is a small town in an old zinc mining district in a mountain valley of southeastern Colorado. Mine waste rock and mill “tailings” remained after over 100 years of mining in the area, leaving associated surface water and groundwater impacts. Atlantic Richfield Company is proposing an innovative approach, which uses lime precipitation and wetland ponds (semi-natural system, also called treatment lagoon in a wetland setting) to treat adit water in the Rico area. Besides using a non-conventional treatment approach, a non-conventional (non-Superfund) regulatory/administrative approach is being proposed. This paper will focus on the water treatment issues and solutions, as well as describing the innovative “watershed” regulatory process.

Jan 1, 2004

By Walter Küng

The Henderson Coarse Ore Conveying System is a three flight belt conveyor system transporting primary crushed molybdenum ore 24 km (15 miles) underneath the North American Continental Divide. One of the conveyors is 16.8 km (55,200fi) in length with 8,200 kW (11,000 HP) of installed power. The overland conveyor contains 11 vertical curves and 9 horizontal curves, some with radii as small as 1,500 m. he system began full operation in December 1999 and is one of the longest and most complicated belt conveyor systems yet constructed. he design of this conveyor system utilized many innovative engineering concepts including low-energy belt covers, low-resistance idlers, torque-controlled tail drives, combined gravity and active winch take-up systems, small radius horizontal curves and belt turnovers. his paper reviews the start-up of the system, discusses the success of the design and addresses the lessons that can be learned from the first 4 years of operation of this unique conveyor system

Jan 1, 2004

By D. Oyler

The National Institute for Occupational Safety and Health’s(NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tail-gate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Jan 1, 2004

By G. Piegols, J. A. Lombardi

Substantial volumes of cyanide are consumed in precious metals mining due to the purposeful destruction of base metal cyanide complexes and free cyanide to meet surface discharge regulations. This destruction of cyanide resource runs counter to the prevailing social ethic of resource conservation wherein cyanide recovery-and-reuse is considered a more socially responsible cyanide use pattern than systematic cyanide destruction. HW Process Technologies, Inc. (HWPT) has developed membrane based methods for the recovery of cyanide from barren solution as a means to reduce cyanide waste. The HWPT Engineered Membrane Separation (EMS™) system uses state-of-the-art spiral wound membrane elements that are engineered specifically for the treatment of high pH cyanide process solutions. The membranes fully reject WAD CN, SAD CN and most minor metals, and partially reject SCN, Free CN and precious metal cyanide from a high clarity barren solution feed to a small volume EMS™ “concentrate” stream. The EMS™ “concentrate” stream is returned to the process. The large percentage of the EMS™ process feed exits the system as cyanide lean EMS™ “permeate.” The EMS™ permeate, after residual cyanide destruction, polishing, and pH adjustment, is, thereafter, typically suitable for discharge. Separately, the HWPT EMS™-PLS method of cyanide recycling is an internal plant cyanide recovery step that removes base metal cyanides from a pregnant leach solution to a small volume EMSTM concentrate stream. The concentrate stream is then typically processed further for the recovery of metals and recovery-recycling of cyanide. The method makes it economically practical to recover gold from Merrill-Crowe or car-bon plant “fouling” solutions, e.g., those with greater than 400 ppm Cu, as might result from the use of the EMS™ method wherein EMS™ concentrate is constantly thrown back into the mine leach solution pool as part of the free cyanide recycle process, or as might result from the single-pass leach treatment of high copper content ores or concentrates. The EMS™ cyanide recovery method for barren solution treatment is shown to be “economic” for the treatment of clear solutions at the approximately 200 ppm total cyanide level (CNT), and for slurries at the approximately 400 ppm total cyanide level, where economic is defined as a 2 year EMS™ plant payback. The EMS™ plant payback calculation includes the beneficial monetary impacts of gold and free cyanide recycling and the avoided operating cost of cyanide destruction.• The cyanide recovery plant payback period is reduced further when the avoided capital costs for cyanide destruction (EMS™ permeate “clear solution CN destruction polish” only required) and/or metals precipitation are considered.

Jan 1, 2004

Anhydrite-based dam constructions, which have been implemented successfully in other geological formations, were investigated with regard to their suitability in salt mines. The laboratory investigations show that anhydrite-based building materials with suitable additives bind safely in spite of the high temperatures in salt mines which normally pre-vent hydration. The dependence of the compressive strength, swelling behavior, porosity and permeability upon the choice and ratio of binding material components and additives was determined. Based on the results of these investigations, a pilot-scale experiment was carried out at the GSF Research Mine Asse (Germany) using a mixture suitable for the prevailing conditions

Jan 1, 2004

By R. Schmidt

The computational fluid dynamics (CFD) technique was used to analyze and optimize the design of the dynamic air classifier integral to Raymond® Bowl Mills. Flow patterns and particle behaviors were modeled in the RB Bowl Mill equipped with various classifier designs. These CFD simulations resulted in the development of a hybrid turbine classifier that has now been field-tested, yielding significant improvements to both mill throughput and product size distribution. This paper demonstrates the viability of CFD as a tool for air classifier design and as a technique that can be extrapolated for use with other pulverizer and classifier arrangements.

Jan 1, 2004

By S. P. Taite, A. R. Charest, P. D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in southwestern Chihuahua State, Mexico. The prospect was discovered by a Francisco Gold Corp. geologist in1995. El Sauzal was encountered as a result of an extensive grass-root exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas Silver Camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiary age. The mineralization appears to be both structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system including kaolinite, illite, alunite, dickite and pyrophyllite. The deposit’s gold distribution, as recorded from drill-hole data and surface samples, varies from 0.2 to 650.0 g/t. The estimated geological resource, as calculated from an independent study completed in 1998, was 3.0 million oz @ 2.03 g/t including a minable reserve of1.8 million oz @ 3.3 g/t.

Jan 1, 2004

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004

By J. Owens

The methodology of quarrying changed significantly in the Indiana Limestone industry in the sixty years between September 11, 1941, the date of the Pentagon groundbreaking ceremony and September 11, 2001 when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on September 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction (and Indiana Limestone) industry can accomplish when working toward a common goal.

Jan 1, 2004

By Paul W. Patton, Christopher Scott Smith

The use of ceramic-in-rubber pulley lagging on bulk material belt conveyors is increasing. Many of the applications have been on pulleys originally installed with rubber lagging. There is a consensus that the fiction characteristics of the ceramic material are significantly better but the factors quoted vary, possibly because the more complex traction mechanism of the dimpled ceramic elements on the belt is not well understood. In this paper we will report and evaluate field data from a number of field installations to provide a study of actual friction characteristics in successful applications for those who desire reliable data for using ceramic-in-rubber lagging in new conveyor designs.

Jan 1, 2004

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By E. Yuksel

Noted as one of the 20 major economies of the world, Turkey is a semi-arid plateau between the Eurasian and the African continents. With its surface area of 780 thousand sq km, it supports a population of 70 million people. While the mining history of Turkey can be traced back as far as 7 000 B.C., mining currently generates only 2% of Turkey’s gross national product. Turkey has 77 of the 90 principal minerals that are mined world-wide. Currently, some 5 000 mine occurrences including copper, lead, zinc, iron, gold-silver, chromite, sepiolite, mercury, and coal deposits, soda ash, marble, zeolite, feldspar, magnesite deposits, as well as the world’s largest known borate deposits, have been discovered and partially explored.

Jan 1, 2004

By V. Dezelic, D. B. Apel

This paper describes the results of laboratory and field experiments conducted to determine the applicability of Ground Penetrating Radar (GPR) for the assessment of the strata thickness and for the identification of separation between bedding planes in stratified rocks. The knowledge about the extent of such separation in the roof layers and information about roof lithology can be used to determine the roof support requirements for underground mines where stratified rocks are present. The laboratory and field experiments were conducted at the Rock Mechanics Laboratory and the Experimental Mine at the University of Missouri-Rolla. The 1.5 GHz high resolution, shallow depth GPR antenna was used for all of the experiments.

Jan 1, 2004

By William R. Yernberg

What a difference a year makes. One year ago, the iron mining industry and the steelmaking industry in the United States were in trouble. Many companies were in bankruptcy, and talk of plant and mine shutdowns was rampant. At that time, it seemed difficult, if not impossible, to remain competitive with imported steel. In addition, the World Trade Organization declared as illegal the tariffs placed on imported steel. And many questioned the viability of the ironmining and steel industry in the United States. At that time, global economic conditions were the main contributors to the industry’s problems. However, since last year’s meeting, changes in global economics have actually helped the steel industry in the United States. Heavy global demand for steel has caused raw-material shortages worldwide. Much of the increased demand is a result of the economic boom in China. In addition, because of a weak U.S. dollar and higher international freight rates, steel imports into the United States have been reduced to about 50 percent of recent levels. These factors have contributed to a rebirth of the U.S. iron mining and steel industries.

Jan 1, 2004

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By Osvaldo A. Bascur, J. Pat Kennedy

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. The lack of an integrated approach makes the profitability of metallurgical plants lag behind that of other industries despite technical advances that have occurred in recent years. This results in significant deterioration in the ability to maintain a "smart” operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. Combining real-time infrastructure with portal technology is becoming an accepted methodology. This paper introduces real-time portals and team sites to support decision making by work- groups which require both real-time and documentary information from manufacturing assets, vendors, head office and the Internet. Workers get insight from the overall process effectiveness index based on key variables such as losses due to plant availability, performance efficiency and rate of quality. Real-time portals and smart clients are part of any real-time performance management (RtPM) solution. Three case studies in large metallurgical complexes are presented. PLANTS ARE YOUR STRATEGIC HANDICAP Information technology is arguably one of the fastest moving technologies used by the mining/metallurgical industry. However, the business model for managing that

Jan 1, 2004

By J. J. K. Daemen

Mining Engineering education is in trouble, if not in crisis. The most visible signs are the decrease in the number of programs that offer the degree, and the continued difficulties in attracting students to the discipline. Unless these trends are reversed, the future of the profession is uncertain, at best. Remedies have been proposed, and some are drastic. They range from consolidating mining engineering education into one or two national schools, to cooperative regional programs, to distance education programs, and to proposals to limit mining engineering to a graduate degree or specialization only. These alternatives deserve serious attention and merit discussion. I hope that one alternative that will remain on the table is the classical and traditional “School of Mines”. A reasonable number of such schools are needed to provide the educational diversity and the critical mass to maintain accreditation and professional registration for their graduates. Most importantly, such an approach is most likely to assure the continued existence of mining engineering as a profession. It also provides the best educational framework to teach mining engineers. However, such Schools are vulnerable, highly susceptible to university budget pressures, and probably can survive only with strong external support.

Jan 1, 2004