Search Documents

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By P. Randall, J. Ickes, S. Chattopadhyay

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (Eh) conditions were performed. Since iron (Fe) is present in large quantities in mining wastes, the effect of Fe on leaching of Hg was also determined. Results show that the Hg concentration increased as the pH of the suspension increased until a pH value of 10.65. Thereafter, the Hg concentration decreased sharply. The Hg concentration, in presence of Fe decreased significantly (1/10thto 1/100th). Kinetics results show a relatively slow rate of leaching in presence of ferric ions. The results obtained from the present study are being used to predict the fate and stability of Hg present in the environment, and will therefore, be useful in dictating the nature and suitability of any remediation treatment.

Jan 1, 2003

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Michel Claisse, R. P. Goel, André J. Rancourt, Kent Murphy

The Malana Hydroelectric Project is a private development located in HimachalPradesh State, India that was commissioned in June 2001. The plant was built and is owned by the Malana Power Company, a subsidiary of the Bhilwara Group of New Delhi. With a total head of 400 m and nominal capacity of 86 MW, the plant is capable of generating 360 GWh annually. The 3,1 km long, 4,0 m diameter power tunnel was designed to be excavated by conventional drill and blast methods. Contrary to traditional practice in India for pressure tunnels of providing a concrete lining, the Malana tunnel was finished mainly with shotcrete. In this way, the tunnel was completed in a period of18 months, a record for recent projects in the Himalayas, and at a cost substantially below that of conventionally lined tunnels. An interesting aspect of the project was the design of the steel tunnel liner linking the power tunnel to the penstock. The length of the liner was fixed finally on the basis of in-situ testing using both hydraulic jacking and doorstopper tests to evaluate the ability of the rock to withstand the internal pressure of4,0 MPa that exist near the downstream end of the tunnel.

Jan 1, 2003

Mining has traditionally been seen as a relatively risky business. Exploration is expensive and the failure rate is high, while start-up costs commonly run to many hundreds of million dollars. To justify the risk and expense, the returns from successful projects must also be high. Accurate estimation of mineral resources and reserves is fundamental to the processes of optimising returns and managing risk in mining developments. Systematic development from initial exploration through a series of development stages enables expenditure and risk to be balanced. As a consequence, large scale modern mine are more akin to manufacturing businesses. This paper examines the life history of a mineral reserve estimate from the perspective of a large mining company against a background of modern estimation and reporting requirements. It will also touch on what constitutes, in the author's opinion, `best' practice in reserve estimation, and how this concept can be spread more widely. [Abstract to be re-written and reduced to 100 words]

Jan 1, 2003

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By Stuart M. Lipofsky, Norm Hutchins

The Metropolitan Water District of Southern California has undertaken the Lake Mathews Outlet Facilities project to replace the existing outlet facilities. In the late1990s, consulting engineers for the District determined that the Lake Mathews Outlet Facilities were susceptible to a catastrophic failure during a seismic event. To ensure a reliable supply of water to Metropolitan’s customers in the Los Angeles area, the District decided to construct new outlet facilities. This Project consists of excavating a large diameter junction shaft, a 6.10 m (20 ft.) horseshoe tunnel, three short 4.88 m(16 ft.) horseshoe bypass tunnels, and a large excavation within a cofferdam that were all driven in difficult rock conditions. Additionally, a new concrete outlet tower was constructed and connected to the existing tunnel by the new bypass tunnels and through the junction shaft. The J.F. Shea Co., Inc. of Walnut, California, is currently finishing the construction of the Lake Mathews Outlet Facilities Project for Metropolitan. The large diameter junction shaft is 50.60 m (166 ft.) deep, excavated 16.15 m (52 ft.) in diameter and lined with a61 cm (2´-0?) thick steel reinforced concrete lining to a finished diameter of 14.63 m (48ft.). The shaft was excavated full face with one stationary shaft three-boom jumbo, modified for the large diameter. The shaft also consists of four sets of gate guides extruding from the shaft wall towards the center of the shaft that provide the ability to operate up to four mechanical gates at any time, to open or close each tunnel. This paper will present the junction shaft excavation and concrete construction techniques, including the innovative slip form method utilized to construct the junction shaft.

Jan 1, 2003

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly, resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 MPa (3,000 psi) as compared to a surface cleaned at 0.7 MPa (100 psi).

Jan 1, 2003

By F. Dudouit, M. M. Mohkam, F. Renault

The Pannerdensch Kanaal Tunnel is part of Holland’s Betuweroute high speed freight railway project linking Rotterdam to inland of Europe. It comprises of twin tunnels, 1620 m long each, with 8.6 m inner diameter. The Tunnel alignment is situated mainly in sandy formations and under high hydrostatique pressure. The over burden cover varies from relatively high to very low, sometimes much smaller than the diameter. One of the special features of the Pannerdensch Kanaal Tunnel is that, over some 250 m, the twin tunnels are to be bored in a back?lled sandpit. Some 490 000cubic meter of sand has been placed and compacted by vibro-?otation to refill the sandpit. The tunneling machine is a 9.8 m slurry shield manufactured by Herrenknecht. Tunnel lining is precast concrete consisting of seven plus one key universal segments. Other than the special feature of boring through re?lled sand, constraints such a slow overburden while crossing under Pannerdensch Kanaal and some lagoons, as well as high liquifaction potential of sandy formations, render this job very unique of the type. Fine studies were conducted in heading’s stability. And, confinement pressures were determined considering different risks of liquefaction and blowout problems. Both tubes have been successfully bored. Several sections have been monitored. The results are quite interesting and in accordance with contract technical conditions.

Jan 1, 2003

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By J. Willison

Over the past decade, the coal mining industry has faced the difficult task of remaining profitable in the midst of declining market prices. Historically, the industry has been quite capable of meeting this challenge by various means. As total costs to mine and market coal continue to increase, new methods of tackling the problem must be implemented. Studies have shown that although many options exist to influence both inby and outby costs, the greatest potential remains in addressing costs at the coal face. Mining operations can positively effect a change in their profitability by either reducing costs, or by increasing production to in turn lower their net cost per man-hour. Original equipment manufacturers can play a key role in both options through the introduction of new technology that permits higher extraction rates, as well as other advantages leading to lower cost coal. A leading advancement over the past 30 – 40 year period has been the advent of progressively higher voltages to operate the mining equipment. This advance enables higher power transmission for a given cable size, operation at lower amperages resulting in less voltage fluctuation, and reduced heat on the cable and electrical components.

Jan 1, 2003

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices that minimize soil compaction will produce better results when forestland is the intended postmining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees. Since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree-survival rate. It is believed that these two soil-compaction parameters may ultimately be used to predict tree-survival rates on reclaimed surface mined lands.

Jan 1, 2003

By K. N. Han

Copper and nickel are extracted from their elemental state, complex sulfides, ores, and other materials such as scrap by leaching them with a solution containing halogen salts - bromine/bromide, and/or iodide/iodine, oxygen and sodium or potassium nitrate. This US patented process is extremely effective yielding 98% recovery in15 minutes for the treatment of chalcopyrite and pentlandite in an autoclave at a temperature of 100°C - 150°C.

Jan 1, 2003

By D. E. Walsh, J. T. Hollow, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Because of their gold value, carbon fines are collected by a filter press. Samples of the carbon fines show that they consist of 20% to 30% carbon, 70% to 80% grit and 0.17 to 0.68 g/kg (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in the form of recrystallized free gold grains, with the balance being the adsorbed gold on the carbon. High recoveries of gold and carbon were obtained from the fines in laboratory tests using froth flotation, with a high rejection of the grit. More than 95% of gold and 90% of carbon can be recovered by three stages of gold flotation followed by two stages of carbon flotation. Key words: Gold recovery, Activated carbon, Flotation

Jan 1, 2003

By J. S. Gardner, R. Woolacott, P. D. Robinson

In 1917, U.S. Coal and Coke Company, a subsidiary of U.S. Steel, opened Mine 31 and built the community of Lynch, Kentucky. For the time this was truly a major engineering accomplishment. It was documented in Howard N. Eavenson’s 1939 AIME paper, “Coal Through the Ages.” In 1996, Arch Coal donated the Portal 31 property to Harlan County for public use. In 2003 the Southeast Education Foundation, Inc. and the Kentucky Coal Museum plan to open the Portal 31 Exhibition Mine to the public to tell the story of Kentucky coalmining through the decades. This presentation will summarize the history of the project, efforts to bring it to reality, the engineering problems, and the challenges of providing a safe environment for visitors.

Jan 1, 2003

By M. Cambridge

During the latter part of the twentieth century exploitation of mineral resources, and gold mining in particular, experienced a resurgence in Europe, with major mining houses and many junior companies involved in exploration and subsequent mine development. Gold projects in particular were actively encouraged and exploration programmes and permitting studies initiated in more than 15 countries, both within the European Union (EU) and the former eastern bloc. During the initial period, governments in many countries provided active support. Following a series of negative environmental mining incidents in the latter part of the century public opinion, often ill-informed, led to political pressure to withdraw governmental assistance. This in turn resulted in the revocation of exploration licenses, and ultimately to the failure to develop a number of potentially world-class mines within the region. Despite these setbacks, gold production in Europe continues, and is probably higher now than 20 years ago. The mining industry is currently coming to terms with both changing attitudes of governments, and the increase in scope and prescriptive nature of legislation. Recent experiences, particularly in Greece and Turkey, exemplify the problems faced by the industry in the region, which are causing major mining companies to reconsider future activities in Europe. The paper presents an overview of European gold mining and its environmental performance in the context of international practice, new legislation, and public perception of mining generally. The rationale of governments in withdrawing support for the industry is questioned, and the feasibility of achieving sustainability where there is no level playing field globally is reviewed. The question is posed to governments, regulators and mining companies alike as to whether there is a future, not only for gold mining, but for the minerals industry in general, within the EU.

Jan 1, 2003

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for the removal of copper from heap-leach solutions without mobile organic phases are a current mining industry need. To satisfy this need, a selective, high-capacity, durable solid material is required. The Idaho National Engineering and Environmental Laboratory (INEEL) developed a set of materials based on current solvent-extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, the author's strategy anchors the chelators to a nonpolymeric solid substrate through the use of a custom-designed linker molecule. The fundamental synthetic routes to these materials have already been established, and attachment to the solid surfaces have been achieved in an efficient manner. The author's continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper-capturing capabilities.

Jan 1, 2003