Search Documents

By M. F. Dibble

Borehole mining, as a viable concept for recovering deep sedimentary mineral resources, historically has been long on promise but short on results. Application of the technology seems best suited for recovery of Miocene phosphate resources on the East Coast of the US. These deposits are potentially enormous in scope and underlie sections of the coastal plain and the near offshore continental shelf. The landside portion of these deposits is generally too deep to mine using conventional open pit methods. Recovery of these minerals requires development of alternative mining systems. A significant proportion of the offshore resources appear to occur at depths below the practical limits of cutter suction dredges and may even exceed the limits of bucket ladder dredges. In most cases, these deposits are covered by overburden that must he removed and redeposited before the mineral section can be mined. The depth, thickness, composition of overburden and environmental sensitivity of a particular location would greatly impact mining system selection. It is probable that dredging would not be an environmentally acceptable mining method in many of the areas underlain by this phosphate rock. In cases such as these, new processes such as borehole mining must be evolved or the resource will remain undeveloped. A borehole mining test program, using an existing prototype borehole system, successfully extracted Miocene phosphate in northeast Florida in 1984-1985. The top of the main mineral zone was 80 m (261 ft) below the surface. Based on the results of this test program. plus subsequent laboratory testing and engineering studies, a new prototype borehole mining system was designed in 1986. This design incorporated several innovations of offering potentially higher productivity and lower power consumption than was achieved with the previous test unit. Economic restraints at that tine prevented the actual construction and testing of this new design.

Jan 1, 1992

By D. B. Sikka

Porphyry type copper ± molybdenum deposits typically occur in the Phanerozoic rocks and have been well documented. During the past two decades a number of porphyry type Cu ± Mo deposits which range in age from 1055 ± 35 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India, Namibia and Zambia. Kalanjkhand porphyry copper deposit M. P., India which is estimated to contain 789 million tonnes averaging 0. 83 percent Cu (millhead-grade); 0.004 percent Mo; 0.2 gm/t Au; 6 gm/t Ag and a cap of 7.532 million tonnes of oxide are averaging 0.8 percent Cu. The economic potential of the expanded copper mining milling, smelting and refining complex to be built in the future at Kalanjkhand, which is the largest porphyry copper deposit discovered to date in the Precambrian rocks of the world is presented.

Jan 1, 1992

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

By R. Riding

Degussa Corporation's peroxide-assisted leaching (PAL) process was evaluated in the batch concentrate leach circuit at Hecla Mining Company's Republic Unit. The product leached in this batch circuit is a high grade gold-silver sulfide (predominately pyrite) flotation concentrate. The primary objectives of the test program were to determine the effects of dilute hydrogen peroxide addition on leaching kinetics, sodium cyanide consumption and precious metals recovery. The results of the testing demonstrated that using dilute hydrogen peroxide produced the following benefits: - 1. Batch leach time requirements decreased by 80%. - 2. Sodium cyanide consumption in concentrate leach reduced by 55%, which translated to an overall plant reduction of 20%. - 3. In the concentrate leach process, gold recovery was increased by 1 to 2%. Because of the excellent metallurgical results achieved with the use of dilute hydrogen peroxide, as well as an economic incentive, PAL has become standard practice in the concentrate leach circuit operation. A complete description of the Republic PAL plant evaluation and performance is provided in this paper. In addition, process chemistry considerations in regard to the role of hydrogen peroxide are discussed.

Jan 1, 1992

By Steven F. Hoerger

Newmont Gold Company is the largest producer of gold in North America. Accurate resource estimates are critical to planning the mining in a year of over 90,000,000 t (100,000,000 tons) of mill, leach and waste grade material, from which over 47 t (1,500,000 oz) of gold are recovered. Resource estimates are updated frequently to take advantage of new drilling, improved geologic understanding and additional production reconciliations. At Newmont Gold, indicator kriging is the primary method being used to create resource estimates. Indicator kriging (IK) is a well accepted method of resource estimation; however, many details of the IK process which are critical to producing a useful resource estimate have not been well documented. An IK model must have several characteristics in order to be a useful resource estimate: the model must take into account geologic features of the mineralization; model creation cannot require too .much time; the model must accurately reflect the effects of selective mining; the model must be stored in an easily accessible format; and the model must be useable with a variety of cutoff grades. This paper will show how Newmont Gold implements the IK process in order to achieve these goals.

Jan 1, 1992

By J. S. Walstrom

Debate on an appropriate, acceptable method of regulating mine and mineral processing wastes has been ongoing since Congress passed the Resource Conservation and Recovery Act (RCRA) on October 21. 1976. Final regulatory determination on which mineral processing wastes are excluded from the RCRA hazardous waste regulations under the Bevill amendment was made by the U.S. Environmental Protection Agency on June 13, 1991. Regardless of whether a mining or mineral processing facility?s waste stream(s) lost or maintained its exclusion status under the Bevill amendment, that facility can expect more stringent regulation of affected waste streams. These more stringent regulations will be added to an already complex regulatory maze, which includes the Clean Air Act (CAA), Clean Water Act (CWA), Safe Drinking Water Act (SDWA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), Superfund Amendments and Reauthorization Act (SARA), and Toxic Substances Control Act (TSCA), as well as state and municipal environmental regulations.

Jan 1, 1992

By J. A. Madonna

Universities and colleges in three countries -Australia, Canada and the United States, recognized the need to establish and reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral exploration companies and private consultants cooperated in the study by providing information regarding their specific training needs for support personnel, the data gathered has been used to identify training area for semi-skilled, skilled and technical personnel in geophysics, including, but not limited to, geo-logical skills, geophysical skills, surveying skills, environ-mental skills, and computer skills. With areas of major educational need defined for geophysical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will he discussed.

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By K. R. Weller, U. J. Sterns, P. S. B. Stewart

Complex sulphide ores usually require very fine grinding of the whole ore stream to achieve adequate liberation. Recent improvements to DSM screens have made this device appear competitive with cyclones in circuits treating these ores. A DSM screen and cyclones were tested in pilot-scale grinding of a copper, lead, zinc ore and the resultant data were used to establish a multi-component simulation model. The model was used to assess the influences of mill environment, circuit flows and pulp densities, final product properties (size, relative size and SG of the values, and liberation characteristics) and a second grinding circuit on capacity and product size distributions, and hence define conditions for which one device is better than the other.

Jan 1, 1992

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By D. E. Ranta, G. H. Giroux, A. W. Randall, D. A. Barr

Zinc-lead ores of the Pine Point District, Northwest Territories, Canada, are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill-hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill-hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1992

By Shuang Shuang Huang, John Fillos

Ozonation was evaluated as an alternative treatment process for leachates of municipal landfills. The study was carried out on leachate from the Fresh Kills Landfill, New York City. The leachate has strong tea color and BOD5 ranging between 90 mg/L and 130 mg/L. The average COD, TOC and NH3-N concentrations were 1800 mg/L , 550 mg/L, and 665 mg/L, respectively. The kinetics of the process were studied in a sparged batch reactor by developing concentration- time profiles for residual color and TOC. Continuous flow experiments were then carried out at two selected contact times. The process was found to be effective in the treatment of leachates for color and TOC removal.

Jan 1, 1992

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By R. J. Miller

The current National commitment to expanding the human presence into the solar system will clearly require major facilities in Earth orbit or possibly on the moon. Such facilities will need large amounts of materials for structural modules, life support, propulsion, and shielding. The heavy transportation costs in fuel required to lift materials from the Earth's surface make a terrestrial-based space system inherently inefficient. A more cost-effective approach would be to provide as much of the required materials as possible from other bodies in space not having the high cost of Earth launch. This paper identifies potential targets for space-based resource utilization, constraints on exploitation, and relative benefits of various sources.

Jan 1, 1992

By Kirk Conway, Richard L. Unger

The U. S. Bureau of Mines conducted a research project to analyze the design of underground mining equipment with respect to ease of maintenance and maintainer safety. The work included a review of maintainability design literature, an analysis of maintenance related accident data, field reviews of equipment designs, and interviews with mine maintenance personnel and equipment manufacturers. Based on the findings, a set of maintainability design recommendations have been prepared. The final recommendations document includes maintainability engineering information for equipment designers, as well as a buyers' guide to aid purchasers of mining machinery in evaluating the maintainability of equipment.

Jan 1, 1992

By Kadri Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. . The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1992

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992