Search Documents

By Peter McKenna

A mineral rights holding can ultimately only be turned to account by the profitable mining of ore on that property. The evaluation of South African gold mineral rights properties must therefore be carried out by assuming that they have potential to form part or all of a future gold mine. Such analysis involves the simulation of many of the estimation procedures that are normally carried out in a full feasibility study of a new mining venture but using far less data. This paper describes in detail the evaluation procedures that may be applied to an individual property and then indicates how these techniques can be applied to a whole mineral rights portfolio.

Jan 1, 1989

By John F. MacDonald, John W. Critchfield

This paper describes the shield excavation of twin transit tunnels, through soft ground, in downtown Seattle. The tunnels are 6.5 m (21.25 ft) diameter and 1525 m (5000 ft) long. Initial support consisted of expandable precast concrete segments, followed by a final lining of cast-in-place concrete. Waterproofing was provided by a PVC membrane installed between the initial support and the final lining. During the course of the excavation a variety of methods were used to control the ground and limit settlement. These included deep wells, vacuum well points, eductor wells, chemical grouting, compaction grouting, jet-grout underpinning, and extensive instrumentation.

Jan 1, 1989

By M. P. Juszli

During the 1980's, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being trans-ported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to far-away customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable Just a few years ago.

Jan 1, 1989

By S. Formby, J. Avraamides

Transportation of sodium cyanide from factory to minesite often attracts adverse comment from both the community and government agencies. In Western Australia the transportation of 30% w/w aqueous sodium cyanide solution raised fears in the community concerning the safety of such material in the event of spillage. The Chemistry Centre of Western Australia initiated a study of the effects of such a spill, to determine appropriate short and long term response strategies. Factors which were considered included the rate of hydrogen cyanide gas release under various climatic and soil conditions and the effect of alternative treatments in reducing such emissions. The data collected have been used to plan emergency response procedures.

Jan 1, 1989

By F. W. Pereira

The Montana Talc ore body was discovered in the summer of 1983, in the Gravelly Range, approximately 25 miles south of Ennis, Montana. Initial drilling indicated a plus-million-ton ore body of high-purity talc. Preliminary analyses were performed on the ore cuttings, .including chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. The results indicated the talc was similar to that currently being marketed from Montana and probably would have good commercial value.

Jan 1, 1989

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By John A. Herbst, William T. Pate

Column flotation is emerging as one of the most important new separation technologies of the decade. Attendant to this development is the need for a quantitative understanding of the dynamic characteristics of columns. An understanding of the many important sub-processes occurring in the cell makes possible the development of dynamic simulators for flotation columns which will aid in the design of control systems for dynamic and steady state optimization. This paper presents a dynamic model for the column flotation cell developed from a population balance point of view similar to that which has been successfully applied to conventional flotation cells. In particular, the mixing that occurs within the pulp is modeled with a distributed-volume, mixer-in-series model as an approximation to the axially dispersed plug flow transport that occurs in the cell. This simpler approach avoids the distributed transport model which often leads to mathematical intractability. Other phenomena dealt with are the attachment and detachment of particles from bubbles in the froth and pulp, the transport of water and the bubble volumes with the froth and pulp phases. Simulation of the flotation of an Illinois No. 6 coal in a pilot plant flotation column were performed to test control strategies.

Jan 1, 1989

By B. Elevli

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value (NPV) and overall economic feasibility of a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. The current practice for doing is to do it by hand on the basis of trial and error analysis. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm is developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application on a gold deposit. The results coming from a case study show that the schedules based on the new method provides improved cash flows compare to a manually done production schedules.

Jan 1, 1989

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By M. D. Baker

Coal-water slurry preparation requires fine grinding and cleaning of coal by flotation. Finer grinding leads to increased ball wear and its effect on the surface properties of coal becomes of concern. Marked ball wear tests were performed to study the effects of oxygen, pH, the soluble species of coal and the addition of pyrrhotite on ball wear. The synergistic action of coal and oxygen greatly enhanced the corrosion of mild steel balls during grinding. Electrochemical measurements on a mild steel electrode in coal slurries and SEM observations of grinding ball surfaces were carried out to explore the corrosive wear mechanism.

Jan 1, 1989

By W. C. Goldberg, E. M. Frizzell

Monitoring slope displacement in open-pit mines can help predict collapses and prevent serious damage, injuries, and fatalities. Early detection of movement may indicate the need to modify slope geometry, initiate dewatering if the slope is wet, or consider artificial support measures such as cable bolting. Slope monitoring at the Berkeley pit was carried out with varying degrees of intensity and continuity for about 15 years. Some of the old mine records are still intact and accessible. Slope monitoring data can therefore be collected and published for the benefit of other mine operators. Because prediction of slope failures is empirical in nature, publication of several well documented case studies will be a valuable contribution to the industry. Background - Berkeley pit Open-pit mining of copper from the Berkeley pit, located on the east side of Butte, MT, began in 1955 and ceased in 1982. During that time, about 1 Gt (1.2 billion st) of material were removed to form a pit about 1.8 km wide by 2.1 km long (6000 ft by 7000 ft) at the rim, and 550 m (1800 ft) deep as measured from the high hill on the northwest side. From the south side, the pit only measures 365 m (1200 ft) deep. The Berkeley pit was first owned and operated by Anaconda Minerals Co., and subsequently by Arco. Following its closure in April 1982, the mine began to fill with water. Washington Construction purchased the property in 1986, and Montana Resources Inc. began mining to the east of the Berkeley pit in July 1986. Numerous instances of slope failure were recorded during the course of mining and several intensive geotechnical investigations were conducted in an effort to optimize the mine design. One of the last and most comprehensive studies was initiated in 1977. For purposes of geotechnical analysis, the mine was divided into nine design sectors on the basis of geologic conditions, geographic orientation, and economic importance (Fig. 1). Only two of these sectors - the concentrator and the southeast corner - are considered here. Material properties were obtained from several studies of samples collected from the mine and adjacent areas. The slope was monitored using standard surveying techniques to record the amount of movement in an area. The

Jan 1, 1989

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

By M. Lotfi

The criteria for evaluating equipment operator performance were identified as the changes in reaction time, the changes in physiological responses, and the changes in subjective reporting of stress. Data were collected while the Subjects operated a front-end loader simulator. This report out-lines the components and the tasks generated by the simulator. It explains the simple and basic assumptions underlying the design of the simulator and the methods of data collection. Improvements that can facilitate the collection of data, including the connection of the simulator to a portable personal computer for on site use are discussed. Statistical analysis of data showed significant deterioration in performance. The report concludes that operator performance can be measured and improved. This report shows that the operator tasks can be simulated by means of simple simulators, the complexity of which is determined by the availability of funds and the area of interest of the investigator.

Jan 1, 1989

By John Turner, John A. Gibson, David Cass

Contents A. Introduction B. Description of Robbins Company involvement in several of the English Channel Tunnel projects C. Identification of project requirements and comparison of TBM features D. Description of the manufacturers separate roles in the -235 (T-1) TBM E. T-1 performance to January 15, 1989 F. Summary

Jan 1, 1989

By E. D. Attanasi, M. W. Bultman, J. H. DeYoung

The 1987 recovery in the US mining industry permitted modest increases in exploration expenditures that year (Fig. 1). Favorable market conditions apparently allowed the gains to be sus¬tained in 1988. There was great uncer¬tainty early in the year as to whether world and US economic growth would be a casualty of the October 1987 worldwide stock market crash. By nearly all measures, the performance of the US minerals industry was strong¬. A weak US dollar and the strong growth of worldwide capital spending resulted in in¬creased US exports of con¬sumer and producer durable items as well as strong domes¬tic demand for metals. In fact, 1988 US steel industry exports reached levels not attained since the mid-1970s. It was re¬ported that steel industry labor productivity is now roughly twice the 1981 level. Among metals with signifi¬cant average nominal price increases in 1988 over 1987 levels were copper (43%), alu¬minum (52%0), and zinc (44%). Even though domestic copper production has grown since 1984 by 30% in mining and 24% in refining, em¬ployment in mining and milling is 4% below the 1984 level. Domestic unit costs are reported in the range of $1.10 to $1.33/kg (50 to 60 cents per lb). The US base metals industry is proba¬bly in its best cash position in many years. However, there has not been a large increase in exploration expendi¬tures. This is due mostly to the percep¬tion that worldwide capacity can easily be increased. Industry reports do show that "low cost" copper producers have been buying reserves from weaker com¬panies. The 1987 Society of Economic Ge¬ologists (SEG) survey of exploration activity indicated that 95 cents out of every exploration dollar spent by US and Canadian firms was for base and precious metals (Economic Geology, January 1989). Press reports, though, make it clear that most of that spending was targeted for precious metals. US claim staking data (Fig. 2) rein¬forces this suspicion. The apparent lag in new claim filings in Alaska and phe¬nomenal growth in filings in the lower 48 states suggests that exploration is directed at relatively low risk targets. In the conterminous 48, more than 40% of the new claims were made in Nevada, indicating an emphasis on gold (although even Nevada had some base metals exploration). Even with a price decline during 1988, the difference between the gold price and average global "cash" production cost of $7.30/g ($227 per oz) still leaves room for an attractive return (Northern Miner, 1988). Exploration plans and results Metals Economics Group (Halifax) indicated in its 1988 exploration survey that exploration expenditures by US and South African firms would be at about 1987 levels. It also reported that Canadian and Australian firms were ex¬pected to reduce their exploration spend¬ing significantly. Firms in both coun¬tries were caught in changes in tax laws. In Canada, the Mining Ex¬ploration Depletion Allow¬ance (MEDA) once permitted generous tax write-offs to in¬dividuals investing in miner¬als exploration. It was to be replaced in January 1989 with the Canadian Exploration In¬centives Program (CEIP). Although structured and ad¬ministered differently than MEDA, CEIP can provide an equivalent or possibly greater financial incentive for min¬eral exploration, for junior mining companies. In 1987, it is estimated that junior com¬panies accounted for two¬-thirds of the off-property (or grass roots) exploration ex¬penditures in Canada. Australia will revoke the tax exemption for gold in 1990. Australian operators, therfore, were expected to concentrate efforts on speeding up pro¬duction during 1988 and 1989. In 1988, Chile and Mali announced special efforts to attract gold explora¬tion by foreign companies. The Cana¬dian government continues to express concern about the write-off (and drawdown) of base metal reserves. Falconbridge did announce a new initiative to identify additional base metal reserves in the Sudbury district. Discoveries Gold deposits dominated discoveries

Jan 1, 1989

By Xingshen Wang, Xuefeng Liu

This paper introduces the methods of adjustment over air pressure, air quantity and the method of comprehensive adjustment over air resistance during a mine ventilation survey. The method of selection of weight value for the adjustment is discussed. Finally a calculating method in regard to saving computer memory units and speeding up calculating process is described.

Jan 1, 1989

By John C. Braithwaite

Gold production commenced in New Zealand during the gold rush of 1861, and recovery to date is over 900 tonnes, almost 60% of which was alluvial. New Zealand pioneered development of bucket line dredges during the 1880's. The advent of the modern hydraulic excavator and increased gold price led to a resurgence in alluvial production with about one hundred plants in operation in 1988. The processing plants are mainly floating, with throughputs of 50-100m3/hr fed by backhoes of 20-40 tonne operating weight. Some larger plants with more sophisticated recovery systems have commenced over the last few years, with the largest using a 180 tonne backhoe.

Jan 1, 1989