Search Documents

By D. A. Gulley, L. J. MacDonnell, William A. Vogely

INTRODUCTION Environmental impacts are most commonly associated with air and water pollution. Not- withstanding this fact, to many people the primary disruption caused by mineral extraction is the change in the character of the locale. That is, the environmental impact of mining includes, but is not limited to, the generation of residuals. The dramatic transformation of wilderness or rural land often creates strong reactions to mineral development. Thus, the basic issues of land use management are a useful addition to environmental discussion. In this section, we take up a discussion of federal, state, and local land use management regimes, along with a brief introduction to the potential role of economic analysis. Elsewhere in this volume, land management issues are discussed from other orientations, and the interested reader may wish to look there as well. Locatable Minerals on Federal Lands Legislation and Administration: Access to hard-rock minerals on the public lands is governed by the General Mining Law of 1872. This law declares that "valuable mineral deposits in land belonging to the United States . . . are hereby declared to be free and open to exploration and purchase . . . ." In order to initiate rights, prospectors are required to physically stake claims of specified sizes and shapes following basic procedures set by federal law which may be supplemented by the individual states. Rights to these claims are protected at the exploration stage so long as actual possession is maintained and diligent exploration activity is underway. If a valuable mineral deposit is discovered on the claim, the claimholder earns the exclusive right of possession as against private parties so long as the claim is properly maintained. To maintain this exclusive right the claimholder must per- form $100 worth of labor or improvements, known as assessment work, on each claim every year and make related annual filings with the U. S. Department of the Interior. If the existence of a valuable mineral deposit can be demonstrated, and other legal requirements are met, the claimholder may receive a patent giving full title to the claimed land, including the surface in most cases. The purchase price is either $2.50 or $5 .OO per acre. The Mining Law has remained largely un- changed by legislative amendment during its now more than 100-vear existence. However, while the law itself has not changed, its interpretation and administration have changed considerably. Written at a time of rapid western expansion of the U.S. following the Civil War, the intent of the law was to promote mineral development by inviting unrestricted prospecting and by selling the lands containing mineral deposits at a minimal charge. As federal land policy shifted from one of rapid disposal into private ownership to one of retention and management for a number of uses, mineral patenting requirements have been administered more strictly. The most critical issue concerns what must be demonstrated to establish the existence of a valuable mineral deposit. The so-called "prudent man" standard was established in the case of Castle v. Womble (19 L.D. 455 (1894)):

Jan 1, 1985

By Charles E. Mergentime, J. Marshall Dean

Mergentime/Loram's extension of the Washington, DC Metro Subway System includes construction of dual 1,770-foot tunnels in soft ground, a crossover structure, a fan structure and pumping station, and other related work. This paper describes the overall construction requirements of the Contract, including subsurface conditions; Mergentime's value engineering of the tunneling and compressed air contract requirement; selection of the tunnel boring machine and backup equipment; installation of the compressed air plant; the manufacture, use and evaluation of the tunnel liners; and the tunneling performances during construction of the first tunnel.

Jan 1, 1985

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By Alfred Jr. Petrick, William A. Vogely

INTRODUCTION The scope of mineral finance extends beyond the economic aspects of property evaluation to all of those activities involving acquisition and utilization of funds with an objective to optimize the value of the firm. It must, therefore, en- compass consideration of the overall financial goals of the firm, decisions involving external versus internal growth and domestic versus foreign investments, management of working cap- ital, efforts to minimize the cost of capital, and decisions with regards to the instruments of long- term debt and equity financing. The scope of this section is limited to considerations of special interest to the mineral or petroleum engineer, which include the following aspects of mineral finance: (1) The technical aspects of mineral or coal property or oil and gas reservoir evaluation which provide the basis for estimation and forecasting of revenues and costs. (2) Estimation and forecasting of costs and prices in a inflationary economic environment. (3) Calculation of cash flows which model .. , the investment in minerals, coal or oil, and gas. Such models require assumptions as to the timing of cash flows, escalation of capital and operating costs, base prices, and escalation, the tax regime, royalties, division of profits and the economic aspects of loans. (4) The role of discount rate in the economic analysis of an investment which requires consideration of the opportunity costs of the firm, cost of capital, risk premiums. (5) Risk analysis including application of the concepts of conditional net present value, expected value, and risk preference as well as the application of the techniques of sensitivity and simulation. (6) Selection of application criteria for in- vestment decision making. (7) Capital structure with particular reference to the effect of debt financing. (8) Consideration of sources of funds utilized by the minerals industries. (9) Long-range planning including portfolio analysis. This section is limited to principles, methodologies, and trends in mineral investment, finance, and long-range planning in the United States with a perspective from the year 1984. Consideration of the key concepts is supplemented by case examples of investment risk analysis and financial structure. Important factors affecting mineral investment evaluation during the 1980s include volatile metals prices, cost inflation, and the introduction of techniques requiring the computer and its capacity for improved technical and economic analysis into the hands of those who know most about the industry. The personal computer is replacing the calculator on the desk of the individual analyst and is rapidly becoming a required tool for the study of engineering and economics. Examples of change brought about by the micro-computer include greatly improved techniques of cost estimation, wider application of the computer for project analysis, computer graphics, reserve estimation, geostatistical analysis, mine design and other techniques that capitalize on the ability of the computer to handle

Jan 1, 1985

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By Robert J. Collins

Computer-aided design drafting systems have been employed in plant design for nearly ten years. Current and future systems will include computer-aided engineering as well. This paper will explore the history and development of such systems including computer and workstation hardware, graphics software, and plant design applications software. The paper will also address future systems and will present both the system vendor and the mine mill designer's view. Specific examples of particularly successful applications will be included.

Jan 1, 1985

By N. Cruickshank

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst-prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) micro-seismic activity. Geophysical and engineering methods for detecting these characterisitcs are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1985

By Jerome P. Downey

Treatment of tungsten ore at Anschutz Mining Company's Chicote Grande (Bolivia) operation results in a relatively high grade arsenopyrite byproduct stream. Laboratory and miniplant testwork have been performed at Colorado School of Mines Research Institute to examine the technical feasibility of recovering a marketable arsenic product fr an this source. Process selection was constrained by the remote location of the millsite, which demands an uncomplicated, low maintenance operation. As a result of the research effort, a two-stage roasting/condensing process was developed, featuring the use of an indirect heating method. Arsenic was efficiently extracted and the arsenic trioxide (As203) product consistently exceeded the industrial purity specification of 99.5%. Key process parameters have been secured for extrapolation of the process to pilot or small commercial scale.

Jan 1, 1985

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By M. Hodgson

The redox reactions that occur on pyrrhotite and pentlandite in contact with oxygenated deionized water were examined using voltammetry. Reactions were put forward in which both minerals were progressively hydroxylated to form thermodynamically metastable surface intermediate products. These intermediates were modelled as metal deficient sulphides where a sulphurous layer was coordinated onto the remaining metal sites via polysulphides. Prior to hydroxylation pentlandite exhibited changes in the surface stoichiometry which were not related to pH effects. The formation of polysuiphide-sulphur intermediates were believed to promote collectorless; flotability for the two minerals. Microflotation tests (0.3 g samples) verified that the surface potential and particle size affected the flotation response, excessive oxidation inhibiting the minerals' flotability. Larger scale tests using ore samples (30 g) confirmed that the extent of pulp oxidation, particle size distribution and the presence of frothers affected the flotation response, the findings being in accordance with the postulated model for the hydrophobic species generated on the pentlandite and pyrrhotite surfaces.

Jan 1, 1985

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By R. H. Olson

Pigments are used in two segments of papermaking, as the major component in paper coating formulations and, in small percentages, as fillers in the paper web. Historically, the dominant use has been in coating, however, recent developments have fostered a multifaceted effort to substantially increase the pigment component in the paper furnish. Factors responsible for these developments together with their relationship to recent and forecast changes in papermaking technology are reviewed. Finally, some thoughts are presented on the probable timing and extent of these changes as well as their expected impact on the future demand for the common paper pigments.

Jan 1, 1985

By Robert E. Frey

Regardless of the mechanical design features of a particular air classifier certain basic principles apply. Specifically , there are two forces at work: 1. An air drag force 2. An inertial or centrifugal force. The air drag force has an increasing influence as particles become smaller. A very small low mass particle is easily carried along with an air stream even when turning a corner. Thus, fine particles follow the air away from the classifying zone. Inertial forces increase as the mass of a particle gets larger. Thus oversize particles tend to obey Newton's laws and respond to centrifugal forces or simply continue in a straight path when the airflow changes direction.

Jan 1, 1985

By J. Harrison Daniel

More stringent dust standards, because of quartz in coal, have become a major compliance problem for the coal industry. Reducing quartz levels has become the major focus of the Bureau of Mines dust control research program. Results to date have identified hath the sources of quartz and prospective control technology. Control techniques are being developed for both room-and-pillar and longwall mining underground operations. Techniques include changes in face ventilation, mining cycle modifications, and better roof bolting dust control.

Jan 1, 1985

By L. Adler

When systematically compared to other engineering fields, mining engineering is distinctive in 1) having a total systems concern. 2) dealing with encumbered space and 3) requiring full spectrum practice. The total systems concern results from having to design and then co-ordinate in space and time several major systems: excavating and bulk handling, ground control, life support and normal support. This requirement favors a generalist rather than a specialist approach. In coping with encumbered space especially in underground coal mining, the uncertainties of geologic conditions are compounded by tightness, roughness, remoteness and hazards. Into this difficult setting the total systems * complex is "stuffed," adding congestion and interference. Because of significant ground deterioration a flexible "rapid in-out" approach is usually vital to mining. Full spectrum practice arises from the need to manage, as well as to plan and design, a labor intensive operation. Since market conditions can also fluctuate most aspects of administration are needed in many respects, mining engineering functions relative to civil engineering in a way similar to industrial to mechanical engineering, with encumbered space being crucial. On this basis stress is placed on: 1) personal relations, 2) field work and 3) entrepreneurship, viewing time as money. Specific recommendations for improving engineering, safety and management and leadership are made. Since most new deposits are marginal, by applying these recommendations with high technology they could possibly now be mined on a widespread basis.

Jan 1, 1985

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985