Search Documents

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Dakota D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a costeffective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Jan 1, 2013

By Michael Jenkins

This paper reviews the history of rock burst research in the Coeur d'Alene Mining District of northern Idaho over the last 30 years. Rock bursting is a problem because of a combination of geological factors in the region--complex structure, high horizontal stresses, and strong, brittle rock that readily stores strain energy. The Bureau of Mines has cooperated with industry to study rock burst phenomenon for many years. Early work focused on methods to mitigate bursting problems within the context of existing mining methods. In the 1970's, researchers began investigating methods for altering or controlling conditions that lead to rock bursts. These control measures become part of the stope development that precedes mining or are changes in the mining process itself. Although, researchers continue to develop microseismic techniques, the major research effort focuses on developing a new mining method to reduce the number and severity of rock bursts in order to improve safety and increase productivity in the Coeur d'Alene Mining District.

Jan 1, 1987

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Axel Preusse

In the Ruhr district, pipelines of public and private infrastructure are made of cast iron, steel, plastics or asbestos cement. Legal framework, technical regulations and normative standards define which pipeline materials may be used for the transmission of which kind of product Thus ground water endangering substances as well as inflammable or explosive products are only permitted to be transported in steel-made pipelines. Ground movements, due to underground mining, are transmitted via the soil to the pipeline and cause extra strain within the steel pipeline (Figure I). In extreme cases durable deformations may occur, characterized by an oval profile or a fold in the pipeline. To avoid or minimize damages, balancing elements are installed into the concerning pipeline, reducing the ground movements which might otherwise cause damages. [ ] The distance between the balancing elements is not arranged by random, but by a calculation method developed in a doctoral thesis [Spielberg, 1999] which represents the actual available standards in science and technology. The calculation method considers all relevant influencing variables with impacts on the movement behaviour of steel pipelines in mining areas, such as technical data of pipeline design (e.g. steel grade, wall thickness, weld seam quality), soil conditions (e.g. friction), laying depths of the pipelines, the operational impacts (working pressure, corrosion) and the mining impacts. As of today, mining has caused no damages to steel pipelines protected by this calculation method.

Jan 1, 2004

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016