Search Documents

By Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

Jan 1, 2006

By Damon P. Vandermaat

Coupon testing allows for the rapid understanding of a material?s likely behavior in service conditions, allowing engineers and operators to make informed decisions about the likely service-life of parts when subjected to field conditions. Bend testing has been identified as the best approach for exploring rock bolt susceptibility to stress corrosion cracking (SCC) in underground mining. The bend test specimens used were 2?3 mm thick slivers of steel, cut from the outer edge of a rock bolt. For the specimens, 1350 grade steel was chosen due to its wide use in the industry. The jigs themselves are small assemblies made of stainless steel that are capable of imparting a bending load on the specimens. The jigs were installed at a coal mine located in the Western Coals West of Sydney, Australia, in such a way as to expose the test specimen to water dripping from the mine roof. It is expected that this approach will yield results pointing to the likely SCC mechanisms affecting the service life of rock bolts, as well as demonstrate the jigs? usefulness as an early warning system for SCC. Furthermore, the coupon tests will be correlated against the results of large-scale laboratory tests.

Jan 1, 2012

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Feiya Xu, Syd S. Peng

"As a highly efficient and new surveying and mapping technique, 3D laser scanning technology has been gradually applied to surface subsidence monitoring in mining areas. 3D laser scanning technology was used to monitor the mining subsidence in a coal mining area in this paper. Based on the 3D laser scanning data obtained in March, May, and December 2016 in the studying mining area, the surface subsidence basin and points deformation were acquired. The 3D laser scanning data were compared with that of the conventional surface movement surveying method. The results show that the 3D laser scanning technology could obtain the data of the subsidence basin more efficiently and reflect the true shape of surface subsidence caused by mining. The maximum surface subsidence obtained by 3D laser scanning technology was 3.60m, while the conventional surface movement surveying was 3.56m; the relative observation error between 3D laser scanner and the conventional surface movement surveying was less than 10%. Therefore, it is feasible to apply 3D laser scanning technology to monitor surface subsidence in coal mines.INTRODUCTIONWith the over-exploitation of coal resources, the problem of surface subsidence has become the focus of attention (Peng, 2011; Guo Wenbing, 2012). Setting up observation stations for surface movement was the traditional method to study the characteristic of surface subsidence and its parameters. At present, hundreds of observation stations have been set up in longwall mining, and a large number of measured data have been obtained (Ministry, 2017). However, due to the length of time surveying requires, great workload in the field, the high cost of observation, and difficult protection for monitoring points, conventional observation stations for surface movement have not met the research on surface subsidence. Therefore, as a new surveying and mapping technique, 3D laser scanning technology has been gradually used for surface subsidence monitoring in mining areas (Ma Liguang, 2005). Li Qiu, Qin Yongzhi, and Li Hong (2006) first proposed 3D laser scanning technology in the application of monitoring surface subsidence in 2006. It was showed that the 3D laser scanning technology had obvious advantages in efficiency and accuracy of data acquisition than other methods of deformation monitoring technology of surface subsidence (such as total station, precision level technique, GPS, etc.). Subsequently, Zhang Shu, Wu Kan, and Wang Xiang (2008) and Chen Ranli and Wu Kan (2012) analyzed the feasibility and precision of 3D laser scanning in subsidence monitoring, concluding that the 3D laser scanning can be used to obtain the subsidence basin and the monitoring precision can reach millimeter. Hu Dahe, Wu Kan, and Chen Ranli (2013) introduced the data processing method of 3D laser scanning for surface subsidence in detail. On the basis of a case study, the subsidence basin in subsidence area was obtained, which reflected the shape of mining subsidence basin intuitively and comprehensively. Wang Qisheng, Wu Kan, and Zheng Ruyu (2010) carried out the research on prediction parameters of mining subsidence by using 3D laser scanning data and got the parameters of major influence angle and the offset distance of inflection point. Meng Wanli, Cai Lailiang, and Yang Wangshan. (2017) made a profile analysis for the 3D view of the surface subsidence using 3D laser scanning data and put forward a “Geomagic” method of surface subsidence prediction."

Jan 1, 2018

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Tingkan Lu

To understand the reinforcing mechanisms of the fully grouted resin bolt and clarify its performance in weak roof strata, the field monitoring investigation using instrumented bolts has been conducted in a coal mine. The total time of monitoring was around ten months. In the first 8 month period, the rock bolt performance relates to the initial development of the gateroad and subsequent time dependent strata response. After 8 months, the rock bolt performance relates to the effect of the approaching longwall mining operation, up to the point where the measuring station was destroyed due to the mining operation.

Jan 1, 1998

By Ding Xu Chu

There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.

Jan 1, 1987

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008