Search Documents

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

Large-scale shear apparatus is designed to investigate the shear hehaviour of simulated soft rock joints under constant normal stifmess condition. Regular saw-teeth profiles having inclinations between 9.5" and 26.5" have been tested. The strength envelope based on these test results indicates that predictions made by Panon (1966) are accurate for the lower asperity angles. However, for higher asperity angles, Patton's model overestimates the shear strength especially in the low to medium normal stress range. In contrast, while Barton's model (1973) is realistic for Constant Normal Load (CNL) condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under Constant Normal Stiffness (CNS) condition. An empirical strength envelope for the prediction of peak shear strength of joints is proposed in this study to account for the change in normal stress and surface degradation during CNS shearing.

Jan 1, 1997

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Charles D. Albright

FMC built its first angle bolter in 1969. This was a single mast unit which could drill holes for conventional bolts or angle holes for installing roof trusses. From this drill we learned very quickie that the mast design was an important factor to the success or failure of any angle bolter. The first mast installed on this machine (EXHIBIT 1) was fixed in length with endless chain and hydraulic motor feed. It took less than a shift underground to determine that the fixed length was not going to work. The undulating top created conditions where the mast was too long to be positioned at a 450 angle. Several mast designs were tried and discarded before we felt we had the answer to our problems. (EXHIBIT 2} We developed a mast that would extend or retract without moving the position of the drill unit. This allowed the operator to "wedge" the mast between the floor and roof before starting his drill feed. This arrangement worked exceptionally well, but unfortunately the demand, as perceived by our Sales Department, for angle bolters did not materialize. This unit became an "orphan" and was used by many coal mines until it died a natural death. FMC did not decide to re-enter this market again until 1979. At this time many coal producers were contacted to determine what features should he incorporated into a dual mast angle bolter. From this information we were able to arrive at three main areas of concern that we should consider when designing a new machine. 1. Eliminate overturning moment on drill unit. 2. Provide some sort of steel support near roof line to aid in starting a 15° hole. 3. Dual mast units need a method of raising center of mast rotation to facilitate various mining heights and still maintain a 45° angle and proper distance from rib. I would now like to discuss each of these individually. EXHIBIT 3 indicates the overturning moment resulting from the feed cylinder thrust and the reaction of the drill hit against the roof. To eliminate this moment a mast was designed using two feed cylinders mounted in the plane of the drill center line, thus removing all overturning moments on the drill unit carriage. This mast has been used extensively in vertical drilling with no downtime attributed to wear on mast guides and drill unit supports. The cylinders are designed to provide uniform thrust and feed speed throughout the total stroke. For manufacturing and economic reasons, the final mast design on the first drill was not used for this new drill. A drill steel support mounted on the mast, and positioned by a hydraulic cylinder provides the needed guidance near the roof for starting a hole at a 45° angle. (EXHIBIT 4) This support does not surround the drill steel but simple cradles the drill steel for "collaring" the hole. Once the hole is started, the support can he lowered. The support plate is hinged to allow the drill mast to pass. The advantage of having vertical motion of the center of rotation on a dual mast drill is shown in EXHIBIT 5. Following the criteria recommended by Birmingham Bolt Company, the truss bolts should he at a 45° angle and one fifth of the width of the entry from the rib. Therefore, in an entry 20 ft. wide, the hole should be drilled 4 ft. from the rib and at the 45° angle previously mentioned. With the limitations inherent to dual boom drills, that is, the masts cannot pass each other nor can one mast pass the center line of the machine even if the other is positioned out of the way, it is impossible to accommodate much variation in seam height and maintain the recommended criteria. As shown in EXHIBIT 5, a center of rotation 17 inches above the floor will start a hole 4 ft. and 45°angle at a height of 67 inches. Any height above 67 inches

Jan 1, 1982

By Michael Kelly

Longwall mining is the principal method of underground coal mining in Australia, with 70 million tonnes being produced by longwall mines in 1999. However, the mechanisms that control longwall geomechanics are still not clearly understood resulting in stoppages costing several hundred million dollars per annum The CSIRO has been investigating longwall geomechanics with consultant groups and minesites through several ACARP supported projects since 1994. The research has aimed to improve longwall support design and control methods by defining strata failure mechanisms and their occurrence about underground extraction panels, It also aimed to develop better predictive tools bur a broad range of underground environments. As a result of site studies at more than 8 locations some of the aspects that have been touted to control longwall geomechanics, especially from a 3D aspect are highlighted. These aspects include stress controls, geometry, faulting, depth. longwall width and changes in lithology.

Jan 1, 2000

By Kazem Oraee-Mirzamani

Blasting operations generate seismic effects in underground mines. These effects apply additional dynamic loads on the support system, which should bear both static and dynamic loads. Static loads are caused by the weight of the superincumbent strata, while dynamic loads occur as a result of blasting in the mining area. Identification of the origin and determination of the support system behavior in natural frequencies is crucial in assessing the stability of underground mines. This is because resonance occurs when a support is vibrated with its natural frequencies, which can cause a vibration with the maximum amplitude and subsequently cause extreme deformations. The mechanism of support system deformation during dynamic load displacement has been studied and numerical simulation for the impact of the dynamic loads on stability of supports is carried out using finite element method. The paper introduces a simple technique for improving stability and safety of mining operations. Results obtained and the methodology adopted in this research can help mining design engineers make decisions on adequate support for active mining operations.

Jan 1, 2011

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By John L. Edwards

The underground coal mines in the Lake Macquarie area of the Newcastle Coalfield, New South Wales, Australia are constrained by surface subsidence restrictions as low as 150 mm. The mining environment is shallow, generally between 100 m and 200 m, often multi-seam and commonly overlain by residential development or tidal waters. Most mines use partial or panel and pillar extraction techniques to meet the subsidence restrictions and allow maximum resource recovery. This paper gives an overview of the results of a recent two year government funded research project aimed at developing a mechanistic, geomechanically based mine design criteria for subsidence control. Three extraction layouts were monitored in detail to assess the relationship between mining geometry, pillar behaviour and surface subsidence. Pillars at each site were instrumented with stress cells, convergence monitors and extensometers. Field data was used to initially calibrate, and subsequently, verify stress and displacement predictions made by the three-dimensional displacement discontinuity code, SUBSOL. Back-analysis of the modelling results indicate SUBSOL's capability as a tool to satisfactorily predict surface subsidence magnitudes and pillar loads for alternative pillar and panel layouts.

Jan 1, 1993

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By G. Herget

To improve quality control of roof conditions, a program was carried out at Elliot Lake uranium nines in Ontario, Canada to test a portable TV camera system. This camera has a 29 mm diameter probe and is capable of identifying crock locations, crack width and approximate dip direction. The extent of fractures to the roof was checked with the aid of a vacuum system by placing packers in various boreholes and checking for communication. The removal of some rock bolts indicated an increase in fracture extent.

Jan 1, 1982

By Thomas L. Vandergrift

Multiple-scam mining is becoming more common in the United States, especially in the East, where primary reserves arc being depleted, forcing mining companies to develop secondary seams, Although mine engineers and planners are aware of the basic effects of seam interaction and generally follow guidelines for columnizing entries and avoiding load abutments, mine design earn greatly benefit bum more quantitative estimates of scam interaction effects. This paper presents case studies from two eastern mines subject to seam interaction effects where pre-mining stresses were quantified: the Mingo Logan Coal Company's Mountaineer Alma A Mine, and Peabody Group's Lightfoot No. 2 Mine. In each of these mines. mining is being carried out within 60 to 90 ft of overlying longwall and pillar panels under maximum cover of about 1,100 ft As part of overall mine planning and design efforts al these mines. NSA Engineering performed numerical modeling analyses using the non-linear boundary-element code MULSIM/NL Input parameters were calibrated by modeling areas where ground conditions resulting from seam interaction were well documented. By incorporating actual cover loading based on topography and seam dip, and the integrity of remnant, gate road, arid harrier pillars in the overlying mines, the pre-mining vertical stress in the underlying scants was estimated based on the pre-mining stress, plans for mains, gate road, bleeder, and pillar panels were developed. Although mining experience in these areas has beers somewhat limited to date, she designs developed as a result of these analyses have so far proven successful.

Jan 1, 2000

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982