Search Documents

By Raj R. Kallu

Underground gold mines in Nevada are typically hosted in geologic zones with a wide range of geotechnical properties ranging from blocky competent rock to faulted and highly altered soil-like material. Geotechnical engineering design in weak rock utilizes rock mass classification systems as inputs to both empirical and numerical methods. The most common rock mass classification system utilized in the gold mines of Nevada is the easy-to-use Rock Mass Rating (RMR) system; however, in practice it is difficult to apply in weak to very weak rock masses. This paper attempts to improve the sensitivity of RMR in weak rock masses by utilizing W-RMR?a modified procedure for calculating RMR?and evaluates its performance against other methods of determining RMR for predicting in situ moduli. In-situ rock mass moduli were determined using a portable plate loading device (PPLD), and these data were used to quantify the improved sensitivity of the modified RMR versus existing classification systems. The PPLD was designed for performing rapid and economical in-situ deformability tests in a mining environment. Tests were performed at eight sites yielding thirteen rock mass moduli measurements. Statistical analyses indicate Detailed-Discontinuity RMR-89 and W-RMR provide the best correlations to the in-situ moduli compared to other methods of calculating RMR.

Jan 1, 2014

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By Mingju Liu

China has been suffering from coal and gas outbursts since 1950s. Nowadays, the situation has become worse than ever with the need to mine deeper coal deposits at higher production rates in a more complex underground mining environment. In the year 2006 alone, 37 outbursts occurred in underground coal mines with a death toll of 232. This paper describes a case study of an outburst event, which occurred in July 2006 during the shaft development of the Mengjin Coal Mine, Henan Province, China at a depth of 768m below surface. Detailed analysis of the possible causes that led to the occurrence of the outburst is reported. These include the study of complex geological features, gas storage conditions, possible improper technical management practice as well as incomplete prevention and control measures. Based on the case study and the observation of outburst occurrence in China in the year 2007, suggestions have been put forward to help prevent and control future coal and gas outbursts.

Jan 1, 2007

By Thomas M. Barczak

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Clive Chadbourne

Investigations of world wide coal face strata control practice, the study of theoretical calculations and detailed engineering analysis have been combined to design and select a powered roof support suitable for use in conjunction with the extraction of 4.5-m (14.7- ft) of the 7.5-m (24.6-ft) thick Warwickshire Thick Coal Seam. The interface between geotechnical criteria and engineering design has been closely considered along with the following 3 important factors: Firstly, the need to further improve strata control and operational characteristics whilst producing a wall integrated overall face design. Secondly, to enable the supports to be rapidly transported from face to face in roadways driven at the minimum size for operational requirements. Finally, to provide hydraulic power, automatic control and monitoring systems which will improve operations reduce manpower requirements and improve management information. Clear design requirements were determined in order to allow selection on a commercial basis. A method of tendering is described with the subsequent analysis and selection process. In the event oversupply of coal in the UK resulted in the order not being placed. Brief consideration has been given to supports suitable for reserves to be mined In a few year's time where there is potential for extraction well in excess of 4.5-m (1 4.74.

Jan 1, 1994

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009