Search Documents

Knowledge of initial ground pressures or in-situ stresses and mechanical properties and geological conditions is of great importance in drivage and maintenance of a mine roadway. Field measurements of the in-situ stresses and the geological and mechanical properties have been carried out. However, these methods are really impractical in using in underground mines. Alternatively, back analysis method using measured displacements during drivage of roadway can be used. The paper presents discussion on some problems in applying inverse formulation of back analysis to a roadway driven in an in- homogeneous rock mass. The back analysis is formulated by 2-0 finite element method. The inverse procedure is carried out using a microcomputer, but for the multi-rock layer, a larger computer or a main-frame computer is used due to an iterative procedure.

Jan 1, 1990

By Khamis Y. Haramy

This paper summarizes ground control studies of longwall panel entry systems in two Western U.S. coal mines. Presented are comparisons of in situ pressure change measurements and assessments of chain pillar and entry behavior under a wide range of cover. Results indicate that no one entry system design is universally applicable, and that site-specific factors need to be considered for panel entry design. Relationships between overburden depth, face advance, and magnitude and location of the forward abutment are discussed for western operations. In addition, analysis indicates that use of yield pillars may reduce or eliminate some stress-related problems that plague longwall panel entry design.

Jan 1, 1989

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Nines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemnisoate link forces. This concept has been laboratory tested in the Bureau's Nine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By H. Guo

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By Wenbing Guo

The stability of strip pillar is the key to successful strip pillar mining. In analyzing the stability of the strip pillar, the width of yield zone must be determined. The determination of the width of yield zone has been an important subject for researchers. In this paper, the numerical method was used to study the relationship between the width of yield zone in strip pillar and coal recovery ratio. The results showed that as the recovery ratio increases, the width of yield zone increases exponentially. Accordingly, the formula for determining the width of yield zone was updated and the effect of changing coal recovery ratio on strip pillar deformation is presented.

Jan 1, 2006