Search Documents

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By David R. Hanson

Seismic tomographic imaging, based on the same principles as a medical CAT Scan (Computer-Aided-Tomography). has been used for many years in the oil industry for large-scale subsurface stratigraphic characterization. and has most recently been applied to various structure- and stress-related problems in the coal industry. New developments in signal processing have greatly enhanced the speed, resolution, and range of applications of topographic imaging in underground settings, and recent innovations in data acquisition hardware have further increased data reliability and repeatability. Whereas past structure mapping applications relied on Seismic velocity and/or attenuation tomopraphy within an enclosed seismic source gram receiver array, recent developments in "True Reflective Tomography- (TRT TM) have expanded the application of this technology considerably. For example, in-seam TRT TM seismic reflection tray now he used to image structure, and/or old workings from one general location in the mine face areas of mains and panel developments) well ahead of planned developments largely eliminating the need to probe-hole drill on regular intervals. This new reflective technology bas also been combined with traditional cross-hole seismic tomography-providing a comprehensive, powerful tool for velocity attenuation. and reflective imagine utilizing the same source/receiver array data sets (borehole-to-borehole. borehole-to-entry and entry-to-entry). These new developments in data acquisition and image processing have greatly expanded the variety of applications for tomographic site characterization allowing the mine operator considerable flexibility to cost-effectively characterize previously inaccessible areas of the property. This paper presents examples of 2-D and 3-D .seismic topographic imaging applied to (1) the location of old works in Appalachian room-and-pillar operations and (2) the identification of anomalous zones ahead of mining/tunneling developments these applications demonstrate the state-of-the-art in seismic ground imaging using velocity, attenuation. aril reflection techniques land combinations thereon, and further illustrate the flexibility of data acquisition from a variety of tinning arid tunneling settings. Recent examples are presented from projects in the United States and Europe.

Jan 1, 2000

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By Gregory Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-¬injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

Jan 1, 2004

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By Zhanjing Yu

In this paper, an equation is developed to characterize the relationship between the UBC and plate size using a boundary integral approach. The equation was validated by the results from mo& than seventy (70) plate loading tests of different sizes conducted in various underground coal mines throughout the Illinois Coal Basin. The equation indicates that the UBC decreases as the plate size increases. The fundamental solution for this boundary integral problems is the Boussinesq equation. The load exerted by the plate on the floor surface is assumed to be uniformly distributed. Both normal and tangential loads are considered. It is also assumed that the floor fails in shear in a plate loading test. The equation may provide the mine operators with a useful tool to obtain from a plate load test of any plate size the UBC value required by the regulations.

Jan 1, 1993

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By A. K. Bhattacharyya

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given 'panel and pillar' partial extraction geometry was examined by two-dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992