Search Documents

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By R. W. Hill

Multiseam mining has been carried out at many collieries in South Africa. It the seams are In close proximity difficult and dangerous mining conditions may arise. In the Witbank area multiseam bord and pillar mining has been carried out, while in Natal where the seams are thinner and of a higher quality, total extraction methods are common. Several combinations of multiseam mining have been carried out. The paper highlights a number of case studies and the strata control problems that can arise.

Jan 1, 1995

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

By Karl Brandt

Longwall panel 580 has recently been retreated in the Zollverein 1/2 seam at a depth of approximately 1000m at Auguste Victoria mine with rectangular rockbolted roadways used for both the maingate and tailgate. Although Auguste Victoria mine has been increasingly using rockbolted support since the mid 1990's. this has previously been restricted to tailgates for single use. This panel represents the first use of a rectangular rockbolted roadway as a maingate at Auguste Victoria mine. As such, it represents a significant change in support strategy. As part of the strategy numerical modelling was used to examine expected behaviour of rockbolted roadways at the site, stress changes during face retreat, the feasibility of adopting rockbolted support for the maingate and the reinforcement pattern required. Monitoring instrumentation was installed in both gates to confirm that the support systems were performing satisfactorily as the gates were driven and as the face was retreated. Although the panel is isolated from others in the Zollverein 1/2 seam, markedly different roadway conditions have been experienced in the two gate roads. Favourable conditions were obtained in the maingate, but particularly difficult conditions were encountered in the tailgate. Previous work for the mine had examined interaction with old workings in other seams and shown a vertical stress of 28MPa for the maingate and up to 45MPa for the tailgate. The values from the earlier work were used in the modelling work described, which showed contrasting results given the different stresses. The difference between the gates can be attributed to the interaction. The paper describes the numerical modelling work, the reinforcement systems adopted, the monitoring results, the interaction effects and the comparison between expectations from the numerical modelling results and the conditions actually experienced.

Jan 1, 2002

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Russell C. Frith

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings arc based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations. Results from the study illustrate periodic weighting cycles of varying severity and these are related to the overlying geology in terms of the strength of individual strata units, their thickness and proximity to the longwall extraction. Several different caving mechanisms are identified which contribute to periodic weighting cycles. The importance of recognising weighting cycles in relation to the operation of the longwall face will be discussed in detail. Longwall support design methods are critically examined in relation to the case histories of the monitoring program. The applicability of the said design methods to Australian coal mining conditions is discussed and an outline of design considerations to facilitate productive longwalling is presented. Overall, the paper only "scratches the surface" of the work currently being undertaken by ACIRL in this area, and the findings of that work.

Jan 1, 1992

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By James J. Scott

Over the past two years research, development ad field tests have been conducted on a new product called the "Scott Cable Sling". This work resulted in the awarding of U.S. Patent No. 4265571 on May 5, 1981, to the inventor. Work on this' project was done by the staff of Scott Mine Technical Services, Inc., and is in keeping with its philosophy of advancing mine grad control technology. Recent acceptance by industry has resulted in volume purchases of the product and indications are that it will gain wide acceptance by the mining industry. The system features flexibility in its application and is useful in both roof and rib control. This paper describes the product, discusses its range of applications and cites specific field examples of its use.

Jan 1, 1981

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017