Search Documents

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

By Kot F. Unrug

In the premining stage of engineering design, the only available data are obtained from core drilling. It is often not sufficient for a realistic design of strata control. During the development, an access to the geological formation is created, enabling in situ testing. Obtained data can be utilized accordingly to improve preliminary design. The available methods for testing are described with emphasis on their application for a longwall system. The optimum design ensuring continuous operation of the high output longwalls is critical because their downtime is very expensive. Optimization of ground control measures also has the potential for substantial savings by elimination of unnecessary support.

Jan 1, 1994

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Vincent A. Scovazzo

The Pennsylvania Joint Coal and Gas Committee Gas Well Pillar Study of 1956 is the bases for well protection pillar design in the US and many other countries. An update was necessary because the well construction common to the gas and coal industries as well as mine configurations, mine depth, and extraction thickness have changed considerably since 1956. As initially envisioned the update would involve a similar empirical study that formed the basis of the initial investigation. However, there are no records of any gas or oil well failures related to coal mining since 1956 when mines followed the initial recommendation, making an empirical study problematic. Thus, the study had to be more analytical, which in return required at least some fundamental research into the behavior of the interaction of coal mining and oil and gas wells. A call to industry about research they have undertaken resulted in obtaining excellent research on the subject from three companies; Alpha Natural Resources, Inc., CONSOL Energy Inc., and Range Resources. These research projects were initially undertaken for internal use and not previously published. John T. Boyd Company reanalyzed these studies and determined how their results would affect protective pillar designs. These research projects pointed to the importance of horizontal movement and shear caused by subsidence and the strength of pillars and their foundations. The importance of geology is important in understanding horizontal shear, ground movement, and floor strength. The failure modes of casing and pipe needed to be understood so the threshold of these movements and stresses could be determined.

Jan 1, 2013