Search Documents

By Rudrajit Mitra, Tien Dung Le, Chengguo Zhang, Bruce Hebblewhite, Joung Oh

"Geomechanical and geotechnical characteristics of coal seam are important parameters that directly affect the cavability of top coal in the longwall top-coal caving (LTCC) method. The impact of these parameters such as coal strength, coal deformation modulus, coal discontinuities and top-coal thickness on cavability has not been fully understood in previous numerical analyses. The limitation and selection of the numerical modelling codes were two of the main reasons. In this paper, detailed caving simulations are performed using a 2D distinct element method (DEM) code, UDEC, to study the effect of various critical parameters on top-coal cavability. The numerical analysis evidently shows that the coal deformation modulus, coal discontinuities, and top-coal thickness have considerable influences on cavability. Coal strength is also a factor but to a lesser extent. The results presented in this paper contribute to the understanding of top-coal cavability in different mining environments and facilitate the development of an advanced cavability evaluation criterion. INTRODUCTION The longwall top-coal caving (LTCC) method was originally developed in the 1950s in the former Soviet Union and France (Tien, 1998). The method was nearly abandoned in Europe after the mid-1980s; however, it has been significantly improved and widely applied in China since the late 1980s. A conceptual model of the LTCC method is shown in Figure 1 in which a thick coal seam is divided into two sections including the lower or cutting section, and the upper or top coal section. The lower section of coal seam is mined by conventional longwall method. Meanwhile, the upper section is recovered by caving through the face support. The LTCC method is considered to be the most viable option for mining general thick seams. Compared to the multi-slice longwall (MSL) method, LTCC has the major advantages (Zhongming, 2001; cited by Vakili, 2009):"

Jan 1, 2017

By M. G. Schuerger

The United States Steel Mining Company, Inc., (USM) Lynch District, operated the No. 37 Mine in the Harlan coal seam, Harlan County, Kentucky, from 19'2 until its sale to Arch of Kentucky in 1984. Overburden depth varied from 400 to 2000 feet and mining height varied from 8 to 12 feet. In 1981, because of deep overburden, high seam height, and previous pillar stability problems, U. S. Steel Research and the Lynch Mining District entered into a joint project to measure longwall pillar stress. Eight gateroad pillars were instrumented with a total of 86 vibrating-wire stressmeters under overburden depths varying from 500 to 1550 feet. Stress-increase measurements were taken during: (1) pillar development, (2) retreat of longwall panel No. 1, and (3) retreat of longwall panel No. 2. Total average pillar stress was approximately three times the pre-mining stress with total stress at an individual meter reading 5.5 times the pre-mining stress. When maximum, measured average pillar stress was compared to pillar strength predicted by several popular pillar design methods, the pillars were found to be stronger than predicted. This paper will summarize the pillar instrumentation program and present the results. Stress distributions, average measured pillar stress, and comparison of measured pillar stress to predicted pillar strength by several design methods will be given.

Jan 1, 1984

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Daniel W. H. Su

This paper presents a retrospective assessment of ground control research and its successful application by CONSOL Energy over the past 25 years. Recognizing the need to improve the understanding of coal pillar design mechanics under shallow, medium, and deep covers, an extensive underground coal pillar instrumentation program was initiated in the mid 1980s. Combined with sophisticated numerical modeling technique and laboratory tests, results from this instrumentation program were used to advance the concept of coal pillar design and to demonstrate that numerical modeling can be used to predict in situ coal pillar strength, especially under non-ideal conditions where interface friction and roof and floor deformation are the primary controlling factors. To evaluate the impact of longwall mining, a 10-year subsidence research program was initiated in 1986 that encompassed surface, subsurface, and underground measurements, as well as a sophisticated numerical modeling technique. Results from the research revealed that interface friction and shearing between rock layers within the overburden had a profound effect on surface subsidence development and the resulting strain. Recognizing the impact of horizontal stresses on CONSOL?s mining operations, extensive horizontal stress measurements were conducted using the USBM Borehole Deformation Gage and the CSIRO Mininfrac system in the mid to late 80s. Roof extensometers and CSIRO HI Cells were used to measure roof displacement and roof stress concentration in longwall headgates and tailgates, which resulted in the definition of right-hand and left-hand longwall panels. Pillar design modifications, combined with cable bolt application and innovative standing support installation, were then successfully employed to mitigate horizontal stress impact on the right-hand longwall headgates and left-hand longwall tailgates. An in-house floor bearing capacity test apparatus was fabricated and employed underground to determine mine-specific floor bearing capacities which, along with other geotechnical parameters, were then used in the mine-specific shield design. To promote caving of thick, massive sandstone immediately behind longwall face supports and to improve face conditions, the hydraulic fracturing technique was successfully employed by CONSOL to pre-fracture the sandstone prior to longwall mining. Face monitoring and numerical modeling confirmed the effectiveness of the hydraulic fracturing technique. A roof geology reconnaissance program was initiated by CONSOL in the early 1990s to improve roof control, safety, and production. Information obtained from the reconnaissance program was used successfully to guide mine planning decisions and daily roof support practices.

Jan 1, 2011

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Brian R. A. Wood

Any defect activity resulting from an applied stimulus on a structure will generate a stress wave which travels in the medium under the laws of acoustics, thus the name of acoustic emission (AE). AE techniques can therefore provide information on the deformation of both surface and below ground structures, Two operating coal mines were monitored from the surface, and both mining activity and post mining microseismic activity were detected. The nature of the detected AE signals demonstrated that there were a range of deformation mechanisms in operation and that some predictive capabilities were possible with the technique.

Jan 1, 1992

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986